2007 CADILLAC CTS V light

The main components of the instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on page 194.
B. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 171.
C. Recongurable Steering Wheel Controls (CTS)
(If Equipped) or Message Center Controls
(CTS-V). SeeRecongurable Steering Wheel
Controls (SWC) (CTS) on page 169or
Message Center (CTS-V) on page 215.
Steering Wheel Climate Controls (CTS).
SeeSteering Wheel Climate Controls (CTS) on
page 196. Traction Control Disable Button
(CTS-V). SeeTraction Control System (TCS)
(CTS) on page 293orTraction Control
System (TCS) (CTS-V) on page 295.
D. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 198.
E. Windshield Wiper Lever. SeeWindshield
Wipers on page 173.
F. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 168.
G. Audio (Base Audio System) or Audio/Navigation
System (If Equipped). SeeAudio System(s)
on page 258orNavigation/Radio System
on page 279.H. Voice Recognition Button (If Equipped).
See Navigation System Supplement.
I. Audio Volume Knob and Source Button
(CTS Only). SeeAudio Steering Wheel
Controls (CTS) on page 279orAudio Steering
Wheel Controls (CTS-V) on page 280.
J. Storage Compartment or Ashtray (If Equipped).
SeeAshtray(s) and Cigarette Lighter on
page 188.
K. Transmission Shift Lever. SeeAutomatic
Transmission Operation on page 122or
Manual Transmission Operation on page 126.
L. Accessory Power Outlet or Cigarette Lighter
(If Equipped). SeeAccessory Power Outlet(s)
on page 186orAshtray(s) and Cigarette
Lighter on page 188.
M. Climate Control System. SeeDual Climate
Control System on page 189.
N. Glove Box. SeeGlove Box on page 159.
Traction Control Disable Button (CTS).
SeeTraction Control System (TCS) (CTS) on
page 293orTraction Control System (TCS)
(CTS-V) on page 295.
167

4. Scroll through the SETUP menu by turning
the knob.
5. When CONFIGURE SWC KEYS appears on
the display, press the knob once to select it.
6. Scroll through the buttons (1, 2, 3 or 4). Press
the knob to select the desired number.
7. Choose a new function for the control by
scrolling through the list of available functions.
8. Once you have highlighted your choice, press
the knob once to select it.
The control you selected is now programmed
with the function you selected.
9. Press the CLR (CLEAR) button to exit each
menu. To program another control, repeat the
procedure.
If your vehicle has the Navigation system, do the
following:
1. Press the MAIN button located to the lower
left of the display.
2. Press the multi-function button next to the
Setup prompt at the right of the display.3. Press the multi-function button next to Prog
SWC located at the right of the screen.
4. Turn the TUNE/SEL knob to scroll through the
available functions.
5. Once the function desired is highlighted, press
and hold the multi-function button next to the
control you want to program (1, 2, 3 or 4).
The buttons are located at the right of
the display.
When a control is successfully programmed,
the function you selected will appear next
to the number of the control at the right of
the display.
6. Press the multi-function button next to the
Back prompt to exit each menu. To program
another control, repeat the procedure.
When a control is programmed with a function,
that function cannot be used with any other control.
It becomes available again only when another
function is programmed to the control.
170

Turn Signal On Chime
If the turn signal is left on for about 1 mile (1.6 km),
a warning chime will sound and the TURN
SIGNAL ON message will appear on the Driver
Information Center (DIC) display. See “Turn Signal
On” underDIC Warnings and Messages on
page 232for more information.
Headlamp High/Low-Beam Changer
Push forward on the turn signal/multifunction
lever to change the headlamps from low to high
beam. Pull the lever back and then release it
to change from high to low beam.
If you turn the vehicle off with the high beams on,
the high beams will be on the next time you
start your vehicle.
This light on the
instrument panel cluster
will be on, indicating
high-beam usage.
Flash-to-Pass
This feature allows you to use the high-beam
headlamps to signal the driver in front of you that
you want to pass.
Pull and hold the turn signal/multifunction lever
toward you to use this feature. When you do this,
the following will occur:
If the headlamps are off, in low-beam or in
Daytime Running Lamps (DRL) mode, the
high-beam headlamps will turn on. They will
stay on as long as you hold the lever
there. Release the lever to turn them off.
If the headlamps are in high-beam mode, they
will switch to low beam. To return to
high-beam, push the lever away from you.
172

If your vehicle is in cruise control when the
Traction Control System (TCS) begins to limit
wheel spin, the cruise control will automatically
disengage. SeeTraction Control System (TCS)
(CTS) on page 293orTraction Control System
(TCS) (CTS-V) on page 295andStabiliTrak
®
System on page 297. When road conditions allow
you to safely use it again, you may turn the
cruise control back on.
Setting Cruise Control
{CAUTION:
If you leave your cruise control on when
you are not using cruise, you might hit a
button and go into cruise when you do not
want to. You could be startled and even
lose control. Keep the cruise control switch
off until you want to use cruise control.
1. Move the cruise control switch to on.
2. Get up to the desired speed.3. Press in the set button at the end of the lever
and release it.
4. Take your foot off the accelerator pedal.
This light on the
instrument panel cluster
will come on while
cruise control is on.
177

Reducing Speed While Using Cruise
Control
There are two ways to reduce your speed while
using cruise control:
Press in the button at the end of the lever
until the desired lower speed is reached,
then release it.
To slow down in very small amounts, briey
press the set button. Each time you do this,
you will go about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your
vehicle will slow down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills
depends upon your speed, load, and the steepness
of the hills. When going up steep hills, you mayhave to step on the accelerator pedal to maintain
your speed. When going downhill, you may have to
brake or shift to a lower gear to keep the speed
reduced. Applying the brake or shifting into a lower
gear will take you out of cruise control. If you need
to apply the brake or shift to a lower gear due to the
grade of the downhill slope, you may not want to
use the cruise control feature.
Ending Cruise Control
To end a cruise control session, step lightly on the
brake pedal. If your vehicle has a manual
transmission, lightly tapping the clutch pedal will
also end a cruise control session.
Stepping on the brake or clutch pedal will only end
the current cruise control session. Move the
cruise control switch to off to completely turn off
the system.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
the cruise control set speed memory is erased.
179

Headlamps
The exterior lamp control is located in the middle
of the turn signal/multifunction lever. SeeTurn
Signal/Multifunction Lever on page 171.
O(Exterior Lamp Control):Turn the control
with this symbol on it to operate the exterior lamps.
The exterior lamp control has the following
four positions:
9(Off):Turning the control to this position
turns off all lamps except the Daytime Running
Lamps (DRL).
;(Parking Lamps):Turning the control to this
position turns on the parking lamps together
with the following:
Sidemarker Lamps
Taillamps
License Plate Lamps
Instrument Panel Lights
5(Headlamps):Turning the control to this
position turns on the headlamps, together with the
previously listed lamps and lights.
AUTO (Automatic):Turning the control to this
position puts the headlamps in automatic
mode. AUTO mode will turn the exterior lamps
on and off depending upon how much light
is available outside of the vehicle.
Wiper Activated Headlamps
This feature activates the headlamps and parking
lamps after the windshield wipers have been in
use for about six seconds. For this feature to work,
the exterior lamp control must be in AUTO.
When the exterior lamp control is off or in the
parking lamp position and the windshield wiper
control is in any position except off, the Headlamps
Suggested message will appear on the DIC
display. See “Headlamps Suggested Message”
underDIC Warnings and Messages on page 232
for more information.
When the ignition is turned to OFF, the
wiper-activated headlamps will immediately turn
off. They will also turn off if the windshield
wiper control is turned off.
180

Headlamps on Reminder
A warning chime will sound if the exterior lamp
control is left on in either the headlamp or parking
lamp position and the driver’s door is opened
with the ignition off. SeeLights On Reminder on
page 213for additional information.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
The DRL system will make the turn signal lamps
come on when the following conditions are met:
It is still daylight and the ignition is in ON
or START.
The exterior lamp control is in off or AUTO and
the headlamps are off.
The automatic transmission is not in PARK (P).When DRL are on, only your front turn signal
lamps will be on. No other exterior lamps will
be on. Your instrument panel cluster will not be
lit up either.
When the exterior lamp control is in AUTO and it
is dark enough outside, the DRL will turn off
and the low-beam headlamps will turn on. When it
is bright enough outside, the low-beam headlamps
will go off, and the DRL will turn back on. If you
start your vehicle in a dark garage, the automatic
headlamp system will come on immediately.
Once you leave the garage, it will take about
one minute for the automatic headlamp system to
change to DRL if it is light outside. During that
delay, your instrument panel cluster may not be as
bright as usual. Make sure your instrument
panel brightness lever is in the full bright position.
SeeInstrument Panel Brightness on page 184.
181

If it is dark enough outside and the exterior lamp
control is off, a Headlamps Suggested message
will appear on the Driver’s Information Center
(DIC) display. This message informs the driver that
turning on the exterior lamps is recommended
even though the DRL are still on. Turning the
exterior lamp control to AUTO or to the low-beam
headlamp position will turn off the DRL and
cancel the Headlamps Suggested message.
If the parking lamps or the fog lamps were turned
on instead, the DRL will still turn off and the
Headlamps Suggested message will be displayed.
You can turn it off by pressing the OK button if
you have the Navigation audio system or the
CLR (Clear) button if you have the base audio
system.
To drive your vehicle with the DRL off, turn the
exterior lamp control off. Then turn on the fog lamps
or parking lamps, and the DRL will turn off.
The Headlamps Suggested message will appear on
the DIC display. This will work regardless of gear
position and whether or not the parking brake is set.
As with any vehicle, you should turn on the
regular headlamp system when you need it.Light Sensor
The light sensor for the DRL and AUTO headlamp
feature is located on top of the instrument panel.
If you cover the sensor, it will prevent it from
sensing light, and the exterior lamps or the
Headlamps Suggested message will appear on
the DIC whenever the ignition is on.
182