2007 CADILLAC CTS V reset

Change Engine Oil
This message indicates that the life of the engine
oil has expired and it should be changed and
that your vehicle is due for service. See your
dealer. SeeEngine Oil on page 346and
Scheduled Maintenance on page 462for more
information.
When you reset the Change Engine Oil message
by clearing it from the display, you still must
reset the engine oil life system separately. For
more information on resetting the engine oil
life system, seeEngine Oil Life System on
page 349. If you clear this message from the
display, it will not re-appear.
Change Trans (Transmission) Fluid
(Automatic Transmission)
This message indicates that the life of the
transmission uid has expired and it should be
changed. SeeScheduled Maintenance on
page 462andRecommended Fluids and
Lubricants on page 473for the proper uid and
change intervals.When you reset the Change Trans Fluid message
by clearing it from the display, you still must
reset the transmission uid life monitor separately.
For more information on resetting the transmission
uid life monitor, seeAutomatic Transmission
Fluid on page 353.
Check Brake Fluid
This message will display if the ignition is in ON to
inform the driver that the brake uid level is low.
Have the brake system serviced by your dealer as
soon as possible. SeeBrake System Warning
Light on page 205andBrakes on page 371
for more information.
Check Gas Cap
When this message appears on the display, the
gas cap has not been fully tightened. You
should recheck the gas cap to ensure that it is on
and tightened properly. See “If the Light Is On
Steady” underMalfunction Indicator Lamp
on page 209for more information.
235

Service Charging System
This message will display when a problem with
the charging system has been detected. Have your
vehicle serviced by your dealer.
Service Electrical System
This message will display if an electrical problem
has occurred within the Powertrain Control
Module (PCM) or the ignition switch. Have your
vehicle serviced by your dealer.
Service Fuel System
The Powertrain Control Module (PCM) has
detected a problem within the fuel system when
this message appears. Have your vehicle serviced
by your dealer.
Service Idle Control
A problem with the idle control has occurred when
this message displays. Have your vehicle
serviced by your dealer.
Service Stability System
If your vehicle has StabiliTrak®, this message will
be displayed if there has been a problem
detected with StabiliTrak
®.
If this message comes on while you are driving,
pull off the road as soon as possible and stop
carefully. Try resetting the system by turning the
ignition off and then back on. If this message
still stays on, or comes back on again while you
are driving, your vehicle needs service. Have
the StabiliTrak
®system inspected by your dealer
as soon as possible. SeeStabiliTrak®System
on page 297for more information.
Service Steering System
Your vehicle may have a speed variable assist
steering system. SeeSteering on page 298.
This message will be displayed if a problem is
detected with the speed variable assist steering
system. When this message is displayed, you may
notice that the effort required to steer the vehicle
increases or feels heavier, but you will still be able
to steer the vehicle.
239

On all vehicles, features such as climate control
settings, radio preset settings, exterior lighting
at unlock, remote lock and unlock conrmation,
and automatic door locks have already been
programmed for your convenience.
Some vehicles have additional features that can
be programmed including the seat and outside
rearview mirror position.
If your vehicle has the ability to program additional
personalization features, the driver’s preferences
are recalled by pressing the unlock button on
the Remote Keyless Entry (RKE) transmitter,
1 or 2, or by pressing the appropriate memory
button, 1 or 2, located on the driver’s door. Certain
features can be programmed not to recall until
the key is placed in the ignition. To change feature
preferences, see “Entering the Personalization
Menu” following.Entering the Personalization Menu
To enter the feature programming mode, use the
following procedure:
1. Turn the ignition to ON, but do not start the
engine. Make sure an automatic transmission
is in PARK (P) or a manual transmission
has the parking brake set.
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on
the driver’s door armrest. The DIC display
will show either Driver 1 or 2 depending
on which button was selected.
3. Press the PWR/VOL knob to turn the radio on.
4. Press the TUNE/SEL knob once to access the
main menu of the DIC.
5. Turn the TUNE/SEL knob until SETUP is
highlighted.
243

Exiting the Personalization Menu
To exit the personalization portion of the SETUP
menu, press the CLR button once you have
nished making your selections. You will return to
the main audio screen.
If a 15 second time period has elapsed with no
selection made, the SETUP menu will be
exited automatically.
Audio System(s)
Determine which radio your vehicle has and then
read the pages following to familiarize yourself
with its features.
Driving without distraction is a necessity for a
safer driving experience. SeeDefensive Driving on
page 286. By taking a few moments to read this
manual and get familiar with your vehicle’s
audio system, you can use it with less effort, as
well as take advantage of its features. While your
vehicle is parked, set up your audio system by
presetting your favorite radio stations, setting the
tone and adjusting the speakers. Then, when
driving conditions permit, you can tune to
your favorite stations using the presets and
steering wheel controls if the vehicle has them.
{CAUTION:
This system provides you with a far greater
access to audio stations and song listings.
Giving extended attention to entertainment
tasks while driving can cause a crash and
you or others can be injured or killed.
Always keep your eyes on the road and
your mind on the drive — avoid engaging
in extended searching while driving.
Keeping your mind on the drive is important for
safe driving. Here are some ways in which you can
help avoid distraction while driving.
While your vehicle is parked:
Familiarize yourself with all of its controls.
Familiarize yourself with its operation.
Set up your audio system by presetting your
favorite radio stations, setting the tone, and
adjusting the speakers. Then, when driving
conditions permit, you can tune to your favorite
radio stations using the presets and steering
wheel controls if the vehicle has them.
258

QSCANR:Press the SCAN button to enter
scan mode. SCAN appears on the display.
Press the up arrow to scan to the next station.
The radio goes to a station, plays for ve seconds,
then goes to the next station. Press this button
again to stop scanning.
To scan preset stations, press and hold SCAN for
more than two seconds until you hear a beep
and PSCAN appears on the display. The radio
goes to the rst preset station stored on your rm
keys, plays for ve seconds, then goes to the
next preset station. Press SCAN again to
stop scanning presets.
The radio only scans stations with a strong signal
that are in the selected band.
LOCAL/DISTANT Selection:With this feature you
can set the radio to search for local stations or
stations that are further away for a larger selection.To set this feature to LOCAL or DISTANT, perform
the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until SEEK LOCAL
or SEEK DISTANT appears on the display.
3. Press the TUNE/SEL knob to select either
LOCAL or DISTANT.
4. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
To search for stations, press the SEEK up or down
arrows. If the system is set to LOCAL, SEEK
appears in the display and seeks to stations with
strong signals only. If the system is set to
DISTANT, D-SEEK appears in the display and
seeks to stations with weak and strong signals.
263

Setting Preset Stations
Up to 30 stations (six FM1, six FM2, and six AM,
six XM1 and six XM2 (if equipped)), can be
programmed on the six numbered rm keys, by
performing the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, or AM, or
XM1 or XM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered rm
keys for two seconds until you hear a beep.
The set preset station number appears on the
display above the rm key that it is set to.
Whenever that numbered rm key is pressed
for less than two seconds, the station that
was set returns.
5. Repeat the steps for each rm key.
To set the preset stations with an equalization
setting, DSP (digital signal processing)
setting, or a program type (PTY) setting, see
each of these features later in this section.
When a preset station is selected, once one of
these additional settings is selected, the
preset station remembers each setting and it
remains active, until the setting is selected
off for that preset station.AUTOSTORE PRESETS:To set the preset
stations automatically, perform the following steps:
1. Turn the radio on.
2. Press BAND to select FM1, FM2, or AM.
3. Press the TUNE/SEL knob to enter the
main menu.
4. Turn the TUNE/SEL knob until AUTOSTORE
PRESETS appears on the display.
5. Press the TUNE/SEL knob to select.
AUTOSTORE appears on the display.
The radio automatically searches the band
and selects and stores the six radio stations
with the strongest signal. The stations are
stored by signal strength, not sequential order.
The set preset station number appears on
the display above the rm key that it is set to.
Whenever that numbered rm key is
pressed for less than two seconds, the station
that was set returns.
6. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
When battery power is removed and later applied,
you do not have to reset your radio presets.
264

PRESETS HOME/AWAY:This feature gives you
the ability to store two different kinds of station
presets. HOME can be used for stations available
where you live and AWAY can be for stations
available outside of your local broadcasting area.
To set preset stations for home and away
perform the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until PRESETS
HOME/AWAY appears on the display.
3. Press the TUNE/SEL knob to select. HOME
or AWAY appears on the display.
4. Press the CLR button to exit the display. To
return to the original display, repeatedly press
the CLR button or wait for the display to
time out.
Follow the manual or automatic steps previously
listed for setting the preset rm keys for both home
and away.Setting the Tone (Bass/Treble)
To adjust the bass, midrange, and treble, perform
the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until
BASS-MID-TREBLE appears on the display.
3. Press the TUNE/SEL knob to enter the tone
settings.
4. Press the TUNE/SEL knob to scroll through
the settings.
5. Turn the TUNE/SEL knob to increase or to
decrease the bass, midrange, or treble. If a
station is weak or noisy, decrease the treble.
6. Press the TUNE/SEL knob to set the
adjustment.
7. Press the CLR button to exit the display.
To return to the original display repeatedly
press the CLR button or wait for the display to
time out.
265

AUDIO EQUALIZER:This feature allows you to
select customized equalization settings. To choose
an equalization setting (EQ0 through EQ5),
perform the following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until EQUALIZER
appears on the display.
3. Press the TUNE/SEL knob to set the
equalization setting. The equalization setting
appears on the display.
4. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
The equalization settings are preset to
EQ0 (Normal), EQ1 (Pop), EQ2 (Rock),
EQ3 (Jazz), EQ4 (Talk), and EQ5 (Country).Adjusting the Speakers (Balance/Fade)
To adjust the balance or fade, perform the
following steps:
1. Press the TUNE/SEL knob to enter the
main menu.
2. Turn the TUNE/SEL knob until
BASS-MID-TREBLE appears on the display.
3. Press the TUNE/SEL knob to enter the tone
settings.
4. Press the TUNE/SEL knob to scroll to
BALANCE or FADER.
5. Turn the TUNE/SEL knob to adjust the
BALANCE to the right or the left speakers and
the FADER to the front or the rear speakers.
6. Press the TUNE/SEL knob to set the
adjustment.
7. Press the CLR button to exit the display.
To return to the original display, repeatedly
press the CLR button or wait for the display to
time out.
EQ0 does not appear on the display when in
this mode.
266