2007 CADILLAC CTS V ECO mode

If the airow seems low when the fan speed is at
the highest setting, the passenger compartment air
lter may need to be replaced. For more
information, seePassenger Compartment Air Filter
on page 195andScheduled Maintenance on
page 462.
h(Recirculation):This mode keeps outside
air from coming in the vehicle. It can be used
to prevent outside air and odors from entering your
vehicle or to help heat or cool the air inside your
vehicle more quickly. Press this button to
switch between recirculation and fresh air. Press
the auto button to have the system select the best
air delivery mode for your temperature setting.
Recirculation is not available in the defrost mode
and will automatically turn off after 10 minutes
when defog is selected.
Using recirculation for long periods of time may
cause the air inside your vehicle to become too dry
or stuffy. To prevent this from happening, after
the air in your vehicle has cooled, turn the
recirculation mode off or press the auto button.
((Heated Seats):Press this button to turn on
the heated seats. The button on the left controls
the driver’s seat and the button on the right
controls the passenger’s seat. SeeHeated Seats
on page 10.
QPWRR(Power/Driver’s Temperature):Press
the PWR button located on the driver’s side of
the climate control panel to turn the entire climate
control system on or off. Press the up or down
arrow on the switch to increase or decrease
the automatic temperature setting.
QPWRR(Power/Passenger’s Temperature):
Press the PWR button located on the passenger’s
side of the climate control panel to allow the
passenger’s climate control setting to be different
than the driver’s. Press the up or down arrow on the
switch to increase or decrease the automatic
temperature setting for the front passenger.
A/C OFF (Air Conditioning):Press this button to
manually turn off the air conditioning compressor.
Press AUTO to return to automatic operation
or press the A/C OFF button again.
191

Check Tire Pressure
If your vehicle has a Tire Pressure Monitor (TPM)
system, this message indicates that one or
more of the vehicle’s tires are low. SeeStatus of
Vehicle Systems on page 223for information
on checking your vehicle’s tire pressures. Also,
seeTire Pressure Monitor System on page 405
andInation - Tire Pressure on page 402for
more information.
Check Washer Fluid
When this message appears on the display, it
means that your vehicle is low on windshield
washer uid. You should rell the windshield
washer uid reservoir as soon as possible. See
Windshield Washer Fluid on page 369for
more information.
Competitive Driving (CTS-V)
When competitive driving mode is turned on with
the TC (traction control) button, this message
will be displayed on the DIC. The TC light will be
on when the competitive driving mode is on.
The Traction Control System (TCS) will not
operate while in competitive driving mode. You
should adjust your driving accordingly. Seethe CTS-V portion ofTraction Control System
(TCS) (CTS) on page 293orTraction Control
System (TCS) (CTS-V) on page 295for more
information.
Driver Door Ajar
When this message appears on the display, it
means that the driver’s door was not closed
completely. You should make sure that the driver’s
door is closed completely.
Engine Coolant Hot – AC
(Air Conditioning) Off
This message displays when the engine coolant
becomes hotter than the normal operating
temperature. To avoid added strain on a hot
engine, the air conditioning compressor is
automatically turned off. When the coolant
temperature returns to normal, the air conditioning
compressor will turn back on. You can continue
to drive your vehicle.
If this message continues to appear, have the
system repaired by your dealer as soon as
possible to avoid damage to the engine or
transmission.
236

Top Speed – Fuel Cut Off
This message will appear when the Engine
Control Module (ECM) detects that the maximum
speed for your vehicle has been reached. Your
vehicle’s top speed is based on the top speed
rating of the tires. This ensures that your vehicle
stays in a safe operating range for the tires.
Traction Engaged
This message will appear when the Traction
Control System (TCS) is actively limiting wheel
spin. Slippery road conditions may exist if
this message is displayed, so adjust your driving
accordingly. The message will stay on for a
few seconds after the TCS stops limiting wheel
spin. SeeTraction Control System (TCS) (CTS) on
page 293orTraction Control System (TCS)
(CTS-V) on page 295for more information.
Trans (Transmission) Hot – Idle Engine
This message indicates that the transmission
uid in your vehicle is too hot. Stop the vehicle and
allow it to idle until the transmission cools down
or until this message is removed. See also
Transmission Fluid Hot Message on page 219for
more information.
Trunk Open
When this message appears on the display, it
means that the trunk lid of your vehicle was not
closed completely. You should make sure that the
trunk lid is closed completely.
Turn Signal On
If you drive your vehicle for more than about
1 mile (1.6 km) with a turn signal on, this message
will appear as a reminder to turn off the turn
signal. A multiple chime will sound when this
message is displayed.
DIC Vehicle Personalization
If your vehicle has the Navigation system, see the
Navigation system manual for instructions on
operating the DIC for your vehicle.
Your vehicle has personalization that allows you to
program certain features to a preferred setting
for up to two people. The number of programmable
features varies depending upon which model of
the vehicle is purchased.
242

On all vehicles, features such as climate control
settings, radio preset settings, exterior lighting
at unlock, remote lock and unlock conrmation,
and automatic door locks have already been
programmed for your convenience.
Some vehicles have additional features that can
be programmed including the seat and outside
rearview mirror position.
If your vehicle has the ability to program additional
personalization features, the driver’s preferences
are recalled by pressing the unlock button on
the Remote Keyless Entry (RKE) transmitter,
1 or 2, or by pressing the appropriate memory
button, 1 or 2, located on the driver’s door. Certain
features can be programmed not to recall until
the key is placed in the ignition. To change feature
preferences, see “Entering the Personalization
Menu” following.Entering the Personalization Menu
To enter the feature programming mode, use the
following procedure:
1. Turn the ignition to ON, but do not start the
engine. Make sure an automatic transmission
is in PARK (P) or a manual transmission
has the parking brake set.
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. If your vehicle has memory settings, press the
appropriate memory button, 1 or 2, located on
the driver’s door armrest. The DIC display
will show either Driver 1 or 2 depending
on which button was selected.
3. Press the PWR/VOL knob to turn the radio on.
4. Press the TUNE/SEL knob once to access the
main menu of the DIC.
5. Turn the TUNE/SEL knob until SETUP is
highlighted.
243

4. Press the TUNE/SEL knob once to select the
letter. The letter will then appear on the display.
If you make a mistake, press the CLR button.
This will exit the menu. You can then go
back into the menu and edit the name. You
can also press the TUNE/SEL knob repeatedly
to cycle through all the characters until you
reach the character you wish to change.
5. Repeat Steps 3 and 4 until the name you
want is complete. You can program up to
16 characters.
The name you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle. To program
the next feature, enter the personalization
portion of the SETUP menu following the
instructions listed previously.
Congure Display Keys
This feature allows you to customize the functions
of the four soft keys located to the left and right
of the audio display. See “Congurable Radio
Display Keys” underRadio with CD on page 260
for programming information.
Congure SWC (Steering Wheel
Controls) Keys
This feature allows you to customize the functions
of the four steering wheel controls located on
the left spoke of the steering wheel. See
Recongurable Steering Wheel Controls (SWC)
(CTS) on page 169for programming information.
Remote Recall Memory
If your vehicle has the optional memory package,
you will have this feature. When this feature is
turned on, you can recall any previously
programmed seat and mirror controls when the
unlock button on the Remote Keyless Entry (RKE)
transmitter is pressed.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
245

Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 2. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until AUTO EXIT
SEAT is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark will
appear in the box next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.Twilight Delay
This feature allows you to set the amount of time
you want the exterior lamps to remain on after
you exit the vehicle.
Programmable Modes
Mode 1:0:00 seconds
Mode 2:0:15 seconds
Mode 3:0:30 seconds
Mode 4:1:00 minute
Mode 5:1:30 minutes
Mode 6:2:00 minutes
Mode 7:2:30 minutes
Mode 8:3:00 minutes
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since the vehicle left the factory.
248

To determine the mode to which the vehicle is
programmed or to program the vehicle to a
different mode, use the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until TWILIGHT
DELAY is highlighted.
3. Press the TUNE/SEL knob to scroll through
and select the available delay settings.
If you choose Mode 1, the exterior lamps will
not illuminate when you exit the vehicle.
Only one mode can be selected at a time.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Lights Flash at Unlock
This feature ashes the exterior lamps when the
Remote Keyless Entry (RKE) transmitter is used to
unlock the vehicle. The lamps will ash for about
20 seconds unless a door is opened, the ignition is
turned to ACCESSORY, ON, or START, or the RKE
transmitter is used to lock the vehicle.Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until LIGHTS
FLASH AT UNLOCK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
249

To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until HORN
SOUNDS AT LOCK is highlighted.
3. Press the TUNE/SEL knob to switch back and
forth between on and off.
When the mode is turned on, a check mark
will appear next to the feature name.
If you select this feature to be on, Lights Flash At
Lock will also be on. You can choose Lights
Flash At Lock by itself, but Horn Sounds At Lock
will always have Lights Flash At Lock enabled
when it is selected.
The mode you selected is now set. You can either
exit the programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.Exterior Lights at Unlock
This feature turns on the exterior lamps when the
Remote Keyless Entry (RKE) transmitter is
used to unlock the vehicle. The lamps will remain
on for about 20 seconds unless a door is
opened, the ignition is turned to ACCESSORY,
ON, or START, or the RKE transmitter is used to
lock the vehicle.
Programmable Modes
Mode 1:ON
Mode 2:OFF
Before your vehicle was shipped from the factory,
it was programmed to Mode 1. The mode to
which the vehicle was programmed may have
been changed since it left the factory.
To program the vehicle to a different mode, use
the following procedure:
1. Enter the personalization portion of the
SETUP menu following the instructions
listed previously.
2. Turn the TUNE/SEL knob until EXT. LIGHT
AT UNLOCK is highlighted.
251