2007 BUICK RANDEZVOUS ignition

DIC Vehicle Personalization
The DIC is used to program the choices of
two drivers. The drivers are recognized as
DRIVER 1 or DRIVER 2 in the DIC display. You
will let the DIC know which driver you are by using
your Remote Keyless Entry (RKE) transmitter.
Each RKE transmitter was pre-programmed
to belong to DRIVER 1 or DRIVER 2 and the
corresponding numbers, 1 or 2, appear on
the back of the transmitters. Each transmitter may
be programmed differently for each driver’s
preferences (lights, doors, horn, or activate the
programmed radio stations for driver 1 or driver 2)
using your RKE transmitter.
After you press the LOCK button on your RKE
transmitter and the ignition key is in ON, the DIC
will display the identied driver number. The
vehicle will also recall the vehicle customization
features that were last programmed to correspond
to your RKE transmitter.
If you unlock your vehicle using your key instead
of your RKE transmitter, the DIC will not change
drivers and your vehicle will recall the information
from the last transmitter used.If your vehicle does not have a DIC, you do not
have available the vehicle customization features
using the RKE transmitter.
Entering Programming Mode
To program features, your vehicle must be in the
programming mode. Do the following:
1. Turn the ignition key to ON with the vehicle in
PARK (P).
To avoid excessive drain on the battery, it is
recommended that the headlamps are
turned off.
2. Press and release the MODE button, scrolling
through the DIC messages, until
PERSONALIZATION PRESS SET TO BEGIN
is displayed.
3. Press the SET button and TO SELECT
DRIVER PRESS REMOTE LOCK will appear.
Press the LOCK button on the Remote Keyless
Entry (RKE) transmitter. This identies which
RKE transmitter is being programmed by
displaying PERSONALIZATION FOR
DRIVER 1 or DRIVER 2.
240

4. The program mode message will appear in
the message center as an indication that
your vehicle is ready to begin programming.
5. Follow the instructions given by the DIC.
Headlamp Exit Delay
This feature allows you to customize the
headlamps and parking lamps. This feature can
be programmed to one of the following modes:
OFF:The headlamps and parking lamps will not
turn on at the same instant that the ignition is
turned to OFF.
15:The headlamps and parking lamps will stay
on for 15 seconds when the ignition is turned
to OFF.30:The headlamps and parking lamps will stay
on for 30 seconds when the ignition is turned
to OFF.
60:The headlamps and parking lamps will stay
on for 60 seconds when the ignition is turned
to OFF.
Your vehicle was originally programmed to
30 second mode. The mode may have been
changed since then. To determine the current
mode, or to change the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until HEADLMP EXIT
DELAY appears in the DIC.
3. Press the SET button until the arrow is before
the mode you prefer.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
United StatesCanada
241

Interior Lighting Delay
The interior lighting delay feature can be
programmed to one of the following modes:
OFF:This feature will not illuminate the interior of
your vehicle when all of the doors are closed.
ON:This feature will continue to illuminate
the interior lamps for 25 seconds after all doors
have been closed so that you can nd the ignition
and buckle your safety belt at night.
Interior lighting delay will not occur while the
ignition is in ON. After 25 seconds, the interior
lamps will fade out. The lamps will fade out before
the 25 seconds if one of the following occurs:
The ignition is turned to ON
All doors are locked using the Remote
Keyless Entry (RKE) transmitter
There is no occupant activity detected for an
illumination period of 25 secondsYour vehicle was originally programmed to ON.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until INTERIOR
LIGHTING DELAY appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
242

Interior Lighting On
The interior lighting on feature can be programmed
to one of the following modes:
KEY OUT:The interior lamps will come on for
about 25 seconds whenever you remove the key
from the ignition.
DOOR:The interior lamps will come on for about
25 seconds when any door is opened.
Interior lighting on will not occur while the ignition
is in ON. After 25 seconds, the interior lamps
will fade out. The lamps will fade out before the
25 seconds if one of the following occurs:
The ignition is turned to ON
LOCK is pressed on the Remote Keyless
Entry (RKE) transmitter
There is no occupant activity detected for an
illumination period of 25 secondsYour vehicle was originally programmed to DOOR.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until INTERIOR
LIGHTING ON appears on the DIC.
3. Press the SET button until the arrow is before
KEY OUT or DOOR.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
243

Auto Door Lock/Unlock
The doors will automatically lock when the vehicle
is shifted out of PARK (P). For automatic
unlocking, you can program your vehicle to one of
the following modes:
OFF:When the shift lever is put in PARK (P), the
doors will not unlock automatically.
DRIVER:When the shift lever is put in PARK (P),
only the driver’s door will unlock.
ALL:When the shift lever is put in PARK (P), all
doors will unlock.
Your vehicle was originally programmed to ALL.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Make sure that the AUTO DOOR LOCK
feature is programmed to ON.
3. Press the MODE button until AUTO DOOR
UNLOCK appears on the DIC.
4. Press the SET button until the arrow is before
OFF, DRIVER or ALL.If the auto door unlock feature has been
programmed to DRIVER or ALL, the automatic
door unlock feature can also be programmed
to one of the following modes:
PARK:Unlock when the shift lever is put in
PARK (P).
KEY OUT:Unlock when the ignition key is
removed.
Your vehicle was originally programmed to PARK.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Follow the instructions for programming AUTO
DOOR UNLOCK to DRIVER or ALL listed
previously.
3. Press the MODE button until AUTO DOOR
UNLOCK/PARK KEYOUT appears on the DIC.
4. Press the SET button until the arrow is before
PARK or KEY OUT.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the next
feature available on your vehicle.
244

Delayed Locking
The delayed locking feature can be programmed
to one of the following modes:
ON:Lock your vehicle using the power door
lock switch or the Remote Keyless Entry (RKE)
transmitter while any door is opened, you will
hear three chimes and the doors will not lock.
Five seconds after the last door is closed, all doors
will lock.
Once delayed locking is programmed to ON, you
can do the following:
Cancel the delayed locking by pressing unlock
using the power door lock switch or by fully
inserting the key in the ignition
Override the delayed locking feature by
pressing lock immediately using the power
door lock switch
Let the delayed locking feature complete the
locking of the vehicleOFF:The doors will always lock immediately
when you lock the doors using the power door lock
switch or press LOCK on the RKE transmitter.
Your vehicle was originally programmed to
ON. The mode may have been changed since
then. To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until DELAYED
LOCKING appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
245

Remote Door Unlock
The remote door unlock feature can be
programmed to one of the following modes:
DRIVER/ALL:With the rst press of UNLOCK on
the Remote Keyless Entry (RKE) transmitter,
the driver’s door will unlock, and with the second
press of UNLOCK, within ve seconds of the
rst press, all passenger’s doors will unlock.
ALL:All doors will unlock with every press of
UNLOCK on the RKE transmitter.
Your vehicle was originally programmed to ALL.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until REMOTE DOOR
UNLOCK appears on the DIC.
3. Press the SET button until the arrow is before
DRIVER/ALL or ALL.The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Unlock Feedback
The unlock feedback feature can be programmed
to one of the following modes:
LIGHTS:This mode does the following:
During the day, when the ignition is in OFF
and UNLOCK on the Remote Keyless Entry
(RKE) transmitter is pressed, the headlamps
and parking lamps will ash.
During the night, when the ignition is in OFF,
the headlamps and parking lamps will be
activated for 30 seconds when UNLOCK is
pressed on the RKE transmitter. If you would
like to change the amount of time the
lamps stay on, change the headlamp exit
delay feature.
OFF:The headlamps and parking lamps will not
ash when UNLOCK is pressed on the RKE
transmitter.
246

Exiting Programming Mode
To exit programming mode, do one of the
following:
Shift out of PARK (P).
Turn the ignition key out of ON.
Do not program any commands for one
minute while in the programming mode.
The programming mode message will turn off to
let you know that you are no longer in the
programming mode.
Once you have reached the end of the
personalization features, PERSONALIZATION
SELECTION DONE will appear briey. Then
PRESS SET TO EXIT MODE TO CONTINUE will
appear. Pressing SET will exit you out of the
DIC. Pressing MODE will take you to the beginning
of personalization.
Audio System(s)
Determine which radio your vehicle has and then
read the pages following to familiarize yourself
with its features.
Driving without distraction is a necessity for a
safer driving experience. SeeDefensive Driving on
page 302. By taking a few moments to read this
manual and get familiar with your vehicle’s
audio system, you can use it with less effort, as
well as take advantage of its features. While your
vehicle is parked, set up your audio system by
presetting your favorite radio stations, setting the
tone and adjusting the speakers. Then, when
driving conditions permit, you can tune to
your favorite stations using the presets and
steering wheel controls if the vehicle has them.
250