2007 BUICK LUCERNE Page 221

Battery Replacement
Under normal use, the battery in your RKE
transmitter should last about four years.
You can tell the battery is weak if the transmitter
will not work at the normal range in any location.
If you have to get close to your vehicle before
the transmitter works, it is probably time to change
the battery.
The REPLACE BATTERY IN REMOTE KEY
message in the vehicle’s DIC will display if the
RKE transmitter battery is low. See “REPLACE
BATTERY IN REMOTE KEY” underDIC Warnings
and Messages on page 221for additional
information.
Notice:When replacing the battery, use care
not to touch any of the circuitry. Static from
your body transferred to these surfaces may
damage the transmitter.To replace the battery in the RKE transmitter do
the following:
1. Insert a at object with a thin edge into the
notch, located below the trunk release button,
and separate the bottom half from the top half
of the transmitter.
2. Remove the old battery, but do not use a
metal object to do this.
98

Ignition Positions
With the ignition key in the ignition, the key can be
turned to four different positions:
Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is in all
the way. If none of this works, then your vehicle
needs service.A (OFF):This is the only position in which the
ignition key can be inserted or removed. This
position locks the ignition and transaxle. It is a
theft-deterrent feature.
B (ACCESSORY):This position lets the radio
and windshield wipers operate while the engine is
off. To use ACCESSORY, turn the key clockwise.
C (RUN):This position is where the key returns
to after the vehicle is started. This position displays
some of the warning and indicator lights.
The battery could be drained if you leave the key in
the ACCESSORY or RUN position with the engine
off. You may not be able to start your vehicle if the
battery is allowed to drain for an extended period
of time.
D (START):This position starts the engine.
A warning chime will sound and the Driver
Information Center (DIC) will display DRIVER
DOOR OPEN when the driver’s door is opened if
the ignition is in OFF, ACCESSORY and the key is
in the ignition. SeeDIC Warnings and Messages on
page 221for more information.
114

Windshield Washer
{CAUTION:
In freezing weather, do not use your
washer until the windshield is warmed.
Otherwise the washer uid can form ice
on the windshield, blocking your vision.
J(Washer Fluid):Press and release this
paddle, located at the top of the turn signal/
multifunction lever, to spray washer uid on the
windshield. The wipers will clear the windshield
and either stop or return to your preset speed. For
more washer cycles, press and hold the paddle.
_(Heated Washer Fluid):The heated
windshield washer uid system, if your vehicle has
this feature, may be used to help clear ice, snow,
tree sap, or bugs from your windshield. Sliding the
switch on the turn signal/multifunction lever to
this position and then releasing it will activate the
heated windshield washer uid system. This
activation will initiate four heated wash/wipe cycles.
The rst heated wash/wipe cycle may take up to
40 seconds to occur, depending on outside
temperature. After the rst wash/wipe cycle, it may
take up to 20 seconds for each of the remaining
cycles. The heated windshield washer uid system
may be turned off at any time by sliding the switch
on the turn signal/multifunction lever to this
position again.
When the heated windshield washer uid system
is activated under certain outside temperature
conditions, steam may ow out of the washer
nozzles for a short period of time before washer
uid is sprayed. This is a normal condition.
Washer Fluid Low Add Fluid will be displayed on
the Driver Information Center (DIC) when the
washer uid is low. SeeDIC Warnings and
Messages on page 221.
166

Electric Power Management
The vehicle has Electric Power Management
(EPM) that estimates the battery’s temperature and
state of charge. It then adjusts the voltage for
best performance and extended life of the battery.
When the battery’s state of charge is low, the
voltage is raised slightly to quickly put the charge
back in. When the state of charge is high, the
voltage is lowered slightly to prevent overcharging.
If the vehicle has a voltmeter gage or voltage
display on the Driver Information Center (DIC),
you may see the voltage move up or down. This
is normal. If there is a problem, an alert will
be displayed.
The battery can be discharged at idle if the
electrical loads are very high. This is true for all
vehicles. This is because the generator (alternator)
may not be spinning fast enough at idle to produce
all the power that is needed for very high electrical
loads.A high electrical load occurs when several of the
following loads are on: headlamps, high beams, fog
lamps, rear window defogger, climate control fan at
high speed, heated seats, engine cooling fans,
trailer loads, and loads plugged into accessory
power outlets.
EPM works to prevent excessive discharge of the
battery. It does this by balancing the generator’s
output and the vehicle’s electrical needs. It can
increase engine idle speed to generate more
power, whenever needed. It can temporarily
reduce the power demands of some accessories.
Normally, these actions occur in steps or levels,
without being noticeable. In rare cases at the
highest levels of corrective action, this action
may be noticeable to the driver. If so, a Driver
Information Center (DIC) message might be
displayed, such as Battery Saver Active or Service
Battery Charging System. If this message is
displayed, it is recommended that the driver
reduce the electrical loads as much as possible.
SeeDIC Warnings and Messages on page 221.
176

For Driver Information Center messages related to
URPA, seeDIC Warnings and Messages on
page 221.
If the bumper is damaged, your URPA system
may not work properly. Take the vehicle to
your dealer to repair the system.
Accessory Power Outlet(s)
The accessory power outlets can be used to plug in
electrical equipment such as a cellular telephone or
CB radio.
Your vehicle may have up to three power outlets
depending on the type of front seat you have.
If your vehicle has front bucket seats with a center
console, you will nd two outlets inside the rear
storage compartment. An extra power outlet
can be found in the ashtray.
Your vehicle may have a small cap that must be
pulled down to access the accessory power outlet.
If it does, when not using the outlet be sure to
cover it with the protective cap.
Notice:Leaving electrical equipment on for
extended periods will drain the battery. Always
turn off electrical equipment when not in use
and do not plug in equipment that exceeds the
maximum amperage rating.Certain electrical accessories may not be
compatible to the accessory power outlets and
could result in blown vehicle or adapter fuses. If
you experience a problem see your dealer for
additional information on the accessory power
outlets.
Notice:Adding any electrical equipment to
your vehicle may damage it or keep other
components from working as they should. The
repairs would not be covered by your warranty.
Do not use equipment exceeding maximum
amperage rating of 20 amperes. Check with
your dealer before adding electrical equipment.
When adding electrical equipment, be sure to
follow the proper installation instructions included
with the equipment.
Notice:Improper use of the power outlet can
cause damage not covered by your warranty.
Do not hang any type of accessory or
accessory bracket from the plug because the
power outlets are designed for accessory
power plugs only.
181

If the airbag readiness light stays on after you
start the vehicle or comes on when you are driving,
your airbag system may not work properly.
Have your vehicle serviced right away.
{CAUTION:
If the airbag readiness light stays on after
you start your vehicle, it means the airbag
system may not be working properly. The
airbags in your vehicle may not inate in
a crash, or they could even inate without
a crash. To help avoid injury to yourself
or others, have your vehicle serviced right
away if the airbag readiness light stays on
after you start your vehicle.
The airbag readiness light should ash for a few
seconds when you turn the ignition key to RUN.
If the light does not come on then, have it xed so
it will be ready to warn you if there is a problem.
If there is a problem with the airbag system in your
vehicle, the Service airbag message will appear
on the DIC display. SeeDIC Warnings and
Messages on page 221for more information.
Passenger Airbag Status Indicator
Your vehicle has the passenger sensing system.
Your overhead console has a passenger airbag
status indicator.
When the ignition key is turned to RUN or START,
the passenger airbag status indicator will light ON
and OFF, or the symbol for on and off, for several
seconds as a system check. Then, after several
more seconds, the status indicator will light either
ON or OFF, or either the on or off symbol to let you
know the status of the right front passenger’s frontal
airbag and seat-mounted side impact airbag.
If the word ON or the on symbol is lit on the
passenger airbag status indicator, it means that
the right front passenger’s frontal airbag and
seat-mounted side impact airbag are enabled
(may inate).
United StatesCanada
198

If the traction control system is manually turned
off, this light will come on and the TRACTION
CONTROL OFF message will appear on the DIC.
When the system is active, the light will ash
while the system is limiting wheel spin or assisting
you in controlling the vehicle. You may also feel
or hear the system working. This is normal.
SeeTraction Control System (TCS) on page 283
andDIC Warnings and Messages on page 221
for more information.
StabiliTrak®Indicator Light
This warning light
should come on
briey when the
engine is started.If the warning light does not come on then, have it
xed so it will be ready to warn you if there is a
problem. This light may come on after you rst start
to drive and the STABILITRAK NOT READY
message will appear in the Driver Information
Center (DIC). SeeStabiliTrak
®System on
page 284for more information.
If the light stays on, or comes on when you are
driving a SERVICE STABILITRAK message
will appear in the DIC. This indicates that there
may be a problem with the StabiliTrak
®system
and your vehicle may need service. When
this warning light is on and the SERVICE
STABILITRAK message appears on the DIC,
the system will not assist you in controlling
the vehicle. Adjust your driving accordingly.
When the system is active, the light will ash
while the system is assisting you in controlling the
vehicle. You may also feel or hear the system
working. This is normal.
SeeStabiliTrak
®System on page 284andDIC
Warnings and Messages on page 221for
more information.
203

Tire Pressure Light
This light comes on
briey when you turn
the ignition to RUN.
It will also come on when one or more of your
tires are signicantly underinated.If your vehicle has a Driver Information Center
(DIC), a CHECK TIRE PRESSURE message will
accompany the light. SeeDIC Warnings and
Messages on page 221for more information.
Stop and check your tires as soon as it is safe to do
so. If underinated, inate to the proper pressure.
SeeTires on page 385for more information.
This light will ash for about 60 seconds and then
stay on if a problem is detected with the Tire
Pressure Monitor system.
SeeTire Pressure Monitor System on page 393
for more information.
205