2007 Alfa Romeo 166 ABS

158IN THE EVENT
OF A PUNCTURE
Wheel changing and cor-
rect use of the jack and
spare wheel call for some precau-
tions as mentioned below.
Signal the presence of the station-
ary vehicle according to current
regulations: hazard warning lights,
reflecting triangle, etc.
Any passengers should leave the
car, specially if the vehicle is heav-
ily laden, and wait for the wheel
to be changed out of harm of the
traffic.
If parked on a slope or rough road,
place wedges or other suitable de-
vices under the wheels to prevent
the car from rolling. Do not grease
the threads of bolts before in-
stalling them; they might slip out.
WARNING
The spare wheel is specific
to your model of car: do
not use it on another model or use
the spare wheel of other models on
your car. On cars fitted with tyres
215/55 R16 (*), 225/45 R17,
235/40 R18 and spare wheel with
tyre 215/55 R16 (*), since the
spare wheel is different from the
standard wheels, observe the in-
structions for use given below:
– The spare wheel should only be
used in an emergency.
– Use of the spare wheel should
be kept to a minimum. Do not
drive at speeds of over 80 km/h.
– The car will handle differently
when the spare wheel is fitted.
Avoid sudden acceleration or brak-
ing, sharp corners and fast bends.
– Check at regular intervals that
spare wheel pressure is equal to
2.7 bar (2.7 kg/cm
2).
– Two or more spare wheels
should never be used together.
Have the wheel changed repaired
and refitted as soon as possible.
WARNING
On cars fitted with tyres
215/55 R16 (*), 225/
45 R17, 235/40 R18 and spare
wheel with tyre 215/55 R16 (*),
do not apply the wheel cap on the
spare wheel. The spare wheel has
an orange sticker with the main
cautions about use of the wheel it-
self and instructions for use.
The sticker must absolutely never
be removed or covered.
The sticker contains the following
instructions in four languages:
– WARNING! Only for temporary
use 80 km/h max!
– Replace with standard service
wheel as soon as possible.
– Do not cover these instructions.
The vehicle may fall if the jack is
not positioned correctly.
WARNING
(*) Tyre 205/55 R16 for versions/mar-
kets where applicable.

159
Do not use the jack for
higher capacities than
stated on its label.
Absolutely never tam-
per with the inflation
valve. Do not insert
tools of any kind be-
tween the rim and the tyre.Routinely check that the
pressure of tyres and s-
pare wheel is as speci-
fied in the “Technical specifica-
tions” chapter. Raise the car only
laterally. The car must absolutely
never be raised placing the plate
of the workshop lift arm under
the aluminium crossmember of
the rear suspension.CHANGING A WHEEL
Please be informed that:
– The jack mass is 2.100 kg.
– The jack requires no adjustment.
– The jack cannot be repaired, in the
event of breakage it must be replaced by
another original one.
– No tools other than its operating
crank can be fitted to the jackTo change a wheel proceed as follows:
– Stop the car in such a position that it
is not dangerous for the traffic where it is
possible to change the wheel safely.
Where possible, park on a level, compact
surface.
– Engage the handbrake
– Engage 1st gear or reverse. For cars
with automatic gearbox set the lever to
positionP.
– Open the boot.
– Fold forward the boot mat (A-
fig. 1).
– Slacken the ring nut (A-fig. 2) and
remove the spare wheel.
– Take the tool bag (A-fig. 3) and
bring it near to the wheel to be changed.
The jack only serves for
changing wheels on the
car with which it is provided or on
cars of the same model. It must not
be used for other purposes such as
for instance raising cars of other
models. In no case should it be used
for repairs under the vehicle.
WARNING
P4C00057564PGSm
fig. 1

170
Front sidelights
To replace the bulb (Type B – H6W,
6W):
– Remove the engine compartment cov-
er after turning the fastening pins.
– Turn counter-clockwise and remove
the direction indicator bulb holder (A-
fig. 32) without disconnecting the con-
nector to widen the working space.
– Remove the rubber cap (B) by
pulling the tab (C).– Press the two retaining tabs and re-
move the bulb holder (D- fig. 33).
– Remove the bulb (E- fig. 34) from
the bulb holder, pushing it slightly and
turning it counter-clockwise.– Fit the new bulb into the bulb holder,
pushing it slightly and turning it clock-
wise.
– Push the bulb holder down in its seat.
– Fit the rubber cap.
– Fit the direction indicator bulb holder
and lock it by turning it clockwise.
– Refit the engine compartment cover
and secure it by turning the fastening
pins.
A0D0059m
fig. 32
A0D0062m
fig. 33
A0D0063m
fig. 34

174
Front sidelights
To replace the bulb (Type B – H6W,
6W):
– Remove the engine compartment cov-
er after turning the fastening pins.
– Turn counter-clockwise and remove
the direction indicator bulb holder (A-
fig. 45) without disconnecting the con-
nector to widen the working space.
– Remove the rubber cap (B) by pulling
the tab (C).– Press the two retaining tabs and re-
move the bulb holder (D- fig. 46).
– Remove the bulb (E- fig. 47) from
the bulb holder, pushing it slightly and
turning it counter-clockwise.– Fit the new bulb into the bulb holder,
pushing it slightly and turning it clock-
wise.
– Push the bulb holder down in its seat.
– Fit the rubber cap.
– Fit the direction indicator bulb holder
and lock it by turning it clockwise.
– Refit the engine compartment cover
and secure it by turning the fastening
pins.
A0D0075m
fig. 45
A0D0078m
fig. 46
A0D0079m
fig. 47

191
System/Component Fuse no. Ampere Location
ABI control unit 13 10A fig. 86
ABI control unit – Central locking 19 20A fig. 93
ABI control unit – Front LH power window 18 20Afig. 93
ABI control unit – Front RH power window 3 20A fig. 93
ABI control unit – Rear LH power window 14 20Afig. 93
ABI control unit – Rear RH power window 17 20Afig. 93
ABS control unit 9 5A fig. 86
7 40A fig. 89
3 40A fig. 89
Additional heater (JTD versions) 17 20A fig. 89
13 10A fig. 93
Alarm system (control unit) 12 10A fig. 93
15 10A fig. 93
Alfa Romeo Code System 20 5A fig. 86
16 5A fig. 86
Cell phone (handset) 18 5A fig. 86
5 10A fig. 86
Central locking (ABI control unit) 19 20A fig. 93
Cigar lighter 7 20A fig. 86
Climate control fan 2 30A fig. 89
Climate control unit 19 5A fig. 86
External lights Fuse no. Ampere Location
Brake lights (switch) 9 5A fig. 861 15A fig. 86
Direction indicators 12 10A fig. 93
External lights (control) 5 10A fig. 86
Front fog lights 16 15A fig. 89
Headlights and headlight position
sensor (gas discharge headlights) 6 7.5A fig. 86
IGE control unit:
- brake light switch 1 15A fig. 86
- brake lights 9 5A fig. 86
- headlight spot 11 15A fig. 86
- left side lights 17 10A fig. 86
- rear light units 15 10A fig. 86
- right side lights 8 10A fig. 86
Left dipped beam headlight 12 15A fig. 89
Reversing lights (only versions with
manual gearbox) 13 10A fig. 86
Right dipped beam headlight 10 15A fig. 89
Internal lights Fuse no. Ampere Location
Dashboard light dimmer 5 10A fig. 86
Door mirror control light 15 10A fig. 93
Glovebox light 5 10A fig. 86
Seat warming control light 15 10A fig. 93
Sun visor lights 15 10A fig. 93

207
IMPORTANT - Engine oil
Change the engine oil more frequently
than stated in the Scheduled Mainte-
nance Programme if the car is used pre-
vailingly in one of the following particular-
ly harsh conditions:
– trailer or caravan towing
– dusty roads
– short, repeated journeys (less than 7-
8 km) with an outside temperature of be-
low freezing point.
– engine idling frequently or driving
long distances at low speed (e.g. taxi or
door-to-door deliveries) or in the case of
prolonged inactivity.
IMPORTANT - Air cleaner
Using the car on dusty roads, change
the air cleaner more frequently than stat-
ed in the Scheduled Maintenance Pro-
gramme.
For any doubts about the intervals be-
tween engine oil and air cleaner changes
in relation to how the car is used, contact
Authorised Alfa Romeo Services.IMPORTANT - Fuel oil filter
The variety of the degree of purity of
the fuel oil in commerce may make it
necessary to change the fuel oil filter
more frequently than stated in the Sched-
uled Maintenance Programme. If the en-
gine is “sobbing” it is a sign that the fil-
ter needs changing.
IMPORTANT - Pollen filter
If the car is used frequently in dusty or
heavily polluted environments, you are
recommended to change the activated
carbon filtering element more frequently;
in particular, it should be changed if a
lower flow of air admitted to the passen-
ger compartment is noted.IMPORTANT - Batteries
You are recommended to have the bat-
tery charge conditions checked, prefer-
ably at the onset of winter, to avoid the
possibility of freezing the electrolyte.
This check should be carried out more
frequently if the car is used prevailingly
for short journeys, or if it is fitted with
services that absorb high amounts of cur-
rent permanently with the ignition key
off, especially if installed in the after mar-
ket.
In the case of use of the car in hot cli-
mates or particularly harsh conditions, it
is wise to check the level of the battery
fluid (electrolyte) at more frequent inter-
vals than stated in the Scheduled Mainte-
nance Programme.
IMPORTANT - Remote control
If when pressing the remote control but-
ton of the key, the operating led on the
key flashes briefly only once, the battery
need replacing with other of the same
type.

222
– Before doing any work on the electric
system, disconnect the battery negative
terminal.
If after purchasing the car, you wish to
install electrical accessories which need a
permanent electrical supply (alarm,
hands-free phone, radio-navigator with
satellite anti-theft function, etc.) contact
Authorised Alfa Romeo Services whose
qualified personnel, in addition to sug-
gesting the most suitable devices from
Lineaccessori will be able to evaluate the
total electrical absorption, checking
whether the car’s electric system is able
to support the load required or whether a
battery with higher capacity is necessary.
In fact, these devices continue to absorb
current with the ignition key off (car
parked, engine off) and may gradually
drain the battery. IMPORTANT A battery kept at below
50% of its capacity is damaged by sul-
phation, the capacity is reduced and start-
ing is difficult, there is also more possibili-
ty of freezing (this can occur at –10°C).
In the event of a prolonged stop, refer to
“Vehicle inactivity”.
USEFUL HINTS TO EXTEND
THE LIFE OF YOUR BATTERY
To avoid quickly draining the battery
and to preserve its operating conditions
over the course of time, carefully follow
the instructions below.
– The terminals must always be tight-
ened.
– As far as possible avoid keeping ser-
vices on for a long time with the engine
stopped (radio, hazard warning lights,
parking lights, etc.).
– When leaving the vehicle parked in a
garage, make sure that the doors, bon-
net, boot and interior lids are properly
shut to prevent lights from staying on.
The fluid contained in the
battery is poisonous and
corrosive. Avoid contact with the
skin or eyes. The battery should be
charged in a ventilated place away
from naked flames or possible
sources of sparks: danger of ex-
plosion and fire.
WARNING
Never attempt to charge
a frozen battery before
thawing it, the danger of explosion
exists. If it has frozen, always
check that the inside elements are
not broken (risk of short circuit)
and that the body is not cracked,
with the risk of acid coming out
which is poisonous and corrosive.
WARNING

223
– If electrical welding is to be carried
out on the body of the vehicle the elec-
tronic control units must be disconnected
or removed if the work involves the pro-
duction of high temperatures.The total absorption of these accessories
(standard and installed later) must be
0.6 mA x Ah (of the battery), as shown
in the table below:
BatteryMaximum permissible loadless absorption
100 Ah 60 mA
You are also reminded that services with
high current absorption activated by the
user, such as bottle warmers, vacuum
cleaners, cellular telephone, mini refriger-
ator, etc. accelerate the battery drainage
process if they are powered with the en-
gine not running.
IMPORTANT It should also be noted
that improper branches on connectors of
the electric wiring for installing additional
equipment is dangerous, particularly if
safety devices are involved.
ELECTRONIC
CONTROL UNITS
With normal use of the vehicle no par-
ticular precautions need to be taken.
If interventions are to be carried out on
the electrical system or emergency start-
ing the following must be heeded:
– Always switch off the engine before
disconnecting the battery from the electri-
cal system.
– If battery charging is necessary dis-
connect it from the electric system.
– When starting in an emergency only
an auxiliary battery must be used and not
a battery charger.
– Check that the polarity is correct and
that the connections between the battery
and the electrical system are sound.
– Before connecting or disconnecting
the terminals of the electronic units en-
sure that the ignition key is not in the
MARposition.
– Do not check for current in the cables
by short-circuiting the ends.
If additional systems are
to be installed on the ve-
hicle the danger of incorrectly tak-
ing branches from the electrical
wires cannot be emphasized too
strongly especially if devices es-
sential to the safety of the vehi-
cle and its occupants are involved
(ignition, injection, ABS ...). The in-
correct installation of radio sys-
tems, electronic theft alarms, ra-
diotelephones etc. can interfere
with the electronic control units and
compromises the warranty cover.
For these interventions we re-com-
mend that you contact Alfa Romeo
Authorized Services.The loadless
absorption of all the accessories in-
stalled in the after market must
not exceed 20 mA (reading with
the vehicle stationary).
WARNING