121
VDC AND ASR SYSTEM
FAILURE WARNINGS
In the event of failures the VDC and ASR
systems switch off automatically and the
warning light (A-fig. 145) on the in-
strument cluster turn on glowing steadily.The table below summarises the indica-
tions given by the warning lights in the d-
ifferent operating conditions.In the event of a failure to the VDC or
ASR systems, the car behaves like the
version not equipped with these systems:
at all events, you are recommended to
contact Authorised Alfa Romeo Services
as soon as possible.
Conditions of use System ASR warning VDC warning light ABS warning light EBD warning light
or fault status light on button on cluster on cluster on cluster
Engine starting Lamp On for about On for about On for about On for about
(turning key to MAR) check 4 seconds 4 seconds 4 seconds 4 seconds
Driving inASR on ASR enabled Off Off Off Off
NormalVDC enabled
Conditions ASR off ASR disabled On Off Off Off
Manually VDC enabled
Driving inASR on ASR active Off Flashing Off Off
ConditionsVDC active
that might
ASR off ASR disabled On Flashing Off Off
cause skidding
Manually VDC active
ASR system fault ASR disabled On On Off Off
Fault VDC VDC disabled Off On Off Off
Fault VDC/ASR VDC/ASR disabled On On Off Off
Fault ABS ABS/VDC/ASR disabled On On On Off
Fault EBD ABS/VDC/ASR/EBD disabled On On On On
134
In addition to the notes
and specifications given
below we recommend
that, during the initial period, y-
ou do not drive to full vehicle
performance (for example exces-
sive acceleration, long journeys
at top speed, hard braking etc.).
STARTING
THE ENGINE
IMPORTANT The car is fitted with an
electronic engine lock device. if the en-
gine fails to start see “The Alfa Romeo
CODE system”.The ignition switch is fitted with a safety
device which obliges the driver to return
the ignition key to the STOPposition be-
fore repeating the starting operation if
the engine does not start immediately.
Similarly, when the engine is running,
the device prevents the key being moved
fromMARto the AVV position.
PROCEDURE FOR PETROL
ENGINES
With cold engine:
1) Engage the handbrake.
2) Ensure that the systems and electri-
cal devices, especially if they absorb high
quantities of energy (e.g. heated rear
windscreen), are switched off.
3) Set the gearshift lever to neutral and
fully depress the clutch without pressing
the accelerator.
4) Turn the ignition key to the AVV posi-
tion releasing it as soon as the engine starts.
Never leave the ignition
key in the MAR position
when the engine is
switched off.
5) If the engine does not start immedi-
ately, return the key to the STOPposi-
tion and repeat the operation
With hot engine:
1) Engage the handbrake.
2) Ensure that the systems and electri-
cal devices, especially if they absorb high
quantities of energy (e.g. heated rear
windscreen), are switched off.
3) Set the gearshift lever to neutral and
fully depress the clutch without pressing
the accelerator.
4) Turn the ignition key to the AVV posi-
tion releasing it as soon as the engine starts.
5) If the engine does not start immedi-
ately, return the key to the STOPposition
and repeat the procedure, slightly pressing
the accelerator pedal without pumping it.
Running the engine in
confined areas is ex-
tremely dangerous. The engine
consumes oxygen and produces
carbon monoxide which is a highly
toxic and lethal gas.
WARNING
135
IMPORTANT If it is difficult to start the
engine do not insist with extended attempts
which may damage the catalyzer but con-
tact Alfa Romeo Authorized Services.
PROCEDURE FOR DIESEL
VERSIONS
1) Engage the handbrake.
2) Set the gearshift lever to neutral and
fully depress the clutch without pressing
the accelerator.
3) Turn the ignition key to the MAR
position. the
mwarning light on the in-
strument cluster will turn on.
4) Wait for the
mwarning light to go
off, which will depend on how warm the
engine is. If the engine is very warm the
turning on of the warning light may be so
fast as to go by unobserved.
5) Turn the ignition key to AVV as
soon as the
mwarning light goes off.
Waiting too long would make the glow
plug heating work pointless.IMPORTANT The electric devices that
absorb much energy (air conditioner,
rearscreen heating, etc.) are disengaged
automatically during engine starting.
If the engine does not start at the first
attempt, move the ignition key back to
theSTOPposition before repeating s-
tarting.
If starting is difficult (with the Alfa
Romeo CODE system efficient), do not in-
sist with prolonged attempts.
Only use an auxiliary battery if it is not-
ed that the cause is due to low charge of
vehicle’s battery. Never use a battery
charger to start the engine (see ”If the
battery is flat” in the chapter “In an e-
mergency”).
WARMING THE ENGINE
– Drive off slowly, at medium revs
without accelerating abruptly.
– Do not drive at full performance for
the initial kilometres of the journey. Wait
until the engine coolant temperature is
between 50 and 60°C.
SWITCHING OFF
– Release the accelerator pedal and
wait until the engine reaches idle speed.
– Turn the ignition key to the STOP
position and switch off the engine.
IMPORTANT After a hard journey, it
is advisable to allow the engine to “get
its breath back” before switching off, run-
ning it at idle speed to allow the tempera-
ture in the engine compartment to cool
down. For versions/markets
where applicable the
warning light m flashes
for about 30 seconds after start-
ing the engine meaning that
there is a fault to the glow plug
warming system, in which case,
contact Alfa Romeo Authorized
Services.
140
– During cold weather even apparently
dry roads may be covered with occasion-
al patches of ice. Pay great attention
therefore when driving on roads which
are in the shade, or where rocks or trees
line the road and on which ice may per-
sist.
IMPORTANT To avoid damaging
tyres do not drive on bare patches of as-
phalt with snow chains fitted to the vehi-
cle. In extreme cases proceed slowly and
remove the chains as soon as possible.
When driving on snow with snow chains
fitted, it might be helpful to turn off the
ASR function of the VDC system (if pre-
sent): in fact, in these conditions, skid-
ding of the driving wheels when moving
off makes it possible to obtain higher
traction.
BRAKES
An efficient braking system is vital to
the safety of the vehicle and its passen-
gers.
To use the brakes correctly and to im-
prove their efficiency and limit wear the
following recommendations should be fol-
lowed:– Do not drive with your foot resting on
the brake pedal.
– Ensure that the brake pedal is not
blocked by the mat or other objects.
– Check the efficiency of the braking
system especially before long journeys.
– Check the handbrake and brake fluid
minimum level warning light
xon the
instrument panel. if the
xwarning light
comes on and stays on when the vehicle
is travelling check that the handbrake is
not engaged. If it is not, stop the vehicle
immediately and check the level of the
brake fluid. If the level is low the anom-
aly affecting the circuit should be rectified
immediately. If the
dwarning light
comes on when the brake pedal is
pressed, this means that the front brake
pads have reached the minimum permit-
ted thickness. Have them replaced as
soon as possible by Alfa Romeo Autho-
rized Services.
– The brake fluid is hygroscopic (i.e. it
absorbs humidity). To prevent the onset
of braking anomalies it should therefore
be replaced every two years regardless of
the kilometres travelled.
SERVO BRAKE
The vehicle is equipped with a servo-
braking system (active only when the en-
gine is running). When the engine is sta-
tionary a greater effort is required to de-
press the brake pedal in order to obtain
the same braking effect.
ANTI WHEEL-LOCK SYSTEM
(ABS)
The vehicle is equipped with an ABS sys-
tem with electronic braking device (EBD),
the following should be heeded:
– A slight pulsing may be felt on the
brake pedal caused by the intervention of
the ABS system.
– The performance of the system, in
terms of active safety, should not induce
the driver to take unnecessary and unjus-
tified risks.
– The conduct of the driver must always
reflect weather, road and traffic condi-
tions.
– Deceleration always depends on the
degree of grip between the tyres and the
road surface. Obviously road holding is
141
greatly reduced when there is ice or snow
on the road. Under these conditions the
stopping distance is increased despite the
use of the ABS system.VDC SYSTEM (VEHICLE
DYNAMICS CONTROL):
The VDC is an electronic vehicle stability
control system which, acting on the torque
and braking the wheels in a differentiated
manner, helps to bring the car back to the
correct course in the event of loss of grip.
When the sensors detect the conditions
that would lead to skidding, the VDC sys-
tem intervenes on the engine and on the
brakes producing a stabilising torque.
BRAKE ASSIST (Brake assist in
an emergency)
This system, that cannot be cut out, rec-
ognizes emergency braking on the
ground of the brake pedal operation
speed and allows to speed up the braking
action.
On versions fitted with VDC system, Brake
Assist is deactivated in the event of VDC
system failure (indicated by the switching
on of the relevant warning light).
The ABS system does not
dispense the driver from
driving carefully, especially when
the road is icy, snowed over or
wet.
WARNING
The car is fitted with an
electronic braking device
(EBD). if the
>andxwarning
lights turn on at the same time, this
means that there is an EBD system
fault; in this case violent braking
may be accompanied by early rear
wheel locking, with the possibility
of skidding. Drive the car extremely
carefully to the nearest Authorized
Alfa Romeo workshop to have the
system checked.
WARNING
The turning on of only
the
>warning light
with the engine running normally
indicates a fault to the ABS system
only. In this case the braking sys-
tem is still efficient, though with-
out the aid of the anti-lock device.
Under these conditions perfor-
mance of the EBD system may be
reduced. In this case too, you are
advised to go immediately to the
nearest Authorized Alfa Romeo
workshop, driving in such a way
as to avoid sharp braking, to have
the system checked over.
WARNING
The system performance
levels, in terms of active
safety, should not induce the dri-
ver to run pointless and unjustified
risks. Driving conduct should al-
ways be suited to the conditions of
the road surface, vision and traf-
fic. The responsibility for road
safety is always and anyway the
vehicle driver’s concern.
WARNING
143
WHEELS
The wheels (rims and tyres) installed in
the factory are those which are most suit-
ed to the characteristics of the vehicle
and guarantee the greatest degree of
safety and comfort under all normal dri-
ving conditions.
Before replacing the rims or tyres in-
stalled on your vehicle consult the table
indicating the permitted types given in
the “Technical specifications” chapter of
this manual or contact Alfa Romeo Autho-
rized Services.
The original rim-tyre match should be
followed when changing tyres.IMPORTANTS (when using a s-
pare wheel different from the
other wheels of the car)
– The spare wheel should only be used in
an emergency.
– Use of the spare wheel should be kept
to a minimum. Do not drive at speeds of
over 80 km/h.
– The car will handle differently when the
spare wheel is fitted. Avoid sudden acceler-
ation or braking, sharp corners and fast
bends.
– Check at regular intervals that spare
wheel pressure is equal to 2.7 bar (2.7
kg/cm
2).
SPARE WHEEL
Cars fitted with steel rims and tyres
215/55 R16 (*) have spare wheel iden-
tical with the standard wheels. Cars fitted
with aluminium alloy rims and tyres
215/55 R16 (*), 225/45 R17 and
235/40 R18 have the spare wheel with
steel rim and tyre 215/55 R16 (*).
(*) For versions/markets where applic-
able tyres 205/55 R16.
The jack should only be
used when changing a
wheel; Do not work under the ve-
hicle when this is only supported
using the jack.
WARNING
While the specified di-
mensions remain un-
changed, for travelling safety and
correct operation of the VDC, ASR
and ABS systems the tyres must
absolutely be of the same brand
and type on all wheels, in perfect
conditions and above all of the
specified type and brand.
WARNING
On cars fitted with tyres
215/55 R16 (*), 225/45
R17, 235/40 R18 and spare wheel
with tyre 215/55 R16 (*), since
the spare wheel is different from
the standard wheels, observe the
instructions for use given below.
(*) For versions/markets where ap-
plicable tyres 205/55 R16.
WARNING
149
Useless loads
Do not overload the boot (especially in
town), as this will heavily affect fuel con-
sumption and stability of the vehicle.
Roof rack/ski rack
Remove the roof rack or ski rack imme-
diately after use. These accessories lower
air drag and adversely affect consumption
levels. For particularly bulky loads the use
of a trailer is preferable.
Electric services
Use electric devices only for the neces-
sary time. Rearscreen heating, additional
headlights, wipers and the heater fan
consume a considerable amount of ener-
gy, increasing the need for current highers
fuel consumption (up to +25% in the ur-
ban cycle).Climate control system
The climate control system is a further
load that weighs considerably on the en-
gine inducing higher consumption levels
(on average up to +20%). Outside tem-
perature permitting, preferably use the air
vents.
Spoilers
The use of spoilers that have not been
certified by Alfa Romeo can adversely af-
fect air drag and fuel consumption.DRIVING STYLE
Starting
Do not warm the engine stationary at i-
dle speed or high speed: in these condi-
tions the engine warms much more slow-
ly, increasing consumption and emissions.
It is therefore advisable to move off im-
mediately and slowly, avoiding high
speeds. This will warm up the engine
more quickly.
Pointless manoeuvres
Avoid revving the engine when waiting
at traffic lights and before switching the
engine off. This, like revving before
changing gear, serves absolutely no pur-
pose on modern cars and increases con-
sumption and emission levels.
Gearshifting
As soon as the road and traffic condi-
tions permit it, engage a higher gear. The
use of a low gear to obtain lively acceler-
ating increases fuel consumption.
In the same way, incorrect use of a gear
increases consumption, emission and en-
gine wear.
152 TOWING TRAILERS
GENERALITIES
The vehicle can be used to tow trailers
after a suitable tow hook has been fitted.
Alfa Romeo retails a tow hook which ful-
fils the safety and legal requirements.
This tow hook should be fitted by Alfa
Romeo Authorized Services which will en-
sure a better result and avoid problems
arising which may jeopardise the body-
work warranty cover.The trailer’s braking system must be
separate from the vehicle’s hydraulic sys-
tem.
The vehicle-trailer match must conform
to the specifications of the road-traffic
laws.
Towing weight refers to the overall
weight of a fully loaded trailer including
all accessories and personal belongings.
To avoid sanctions the overall weight of a
fully loaded trailer should be checked to
ensure that it does not exceed the limits
given in the log book.
The vertical loading on the ball hook
should not in any case exceed the limits
specified in the “Technical specifications”
section.When hooking up a caravan or trailer
check that the maximum towable
weights (given in the log book) and the
maximum load permitted on the vehicle’s
tow hook (given on the label applied to
the structure of the trailer), are above or
equal to the overall weight and loading
on the towing eye.
WARNINGS AND
SUGGESTIONS
Some indications concerning driving
with a trailer are given below:
– Install the specific rear-view mirrors
as specified by law.
– Remember that when towing a trailer
steep inclines are harder to climb.
– When travelling down hill engage a
low gear rather than constantly using the
brake.
– Drive within the permitted speed lim-
its for vehicles with trailers. In any case
the maximum speed should never exceed
100 km/h.
The ABS system with
which the car is fitted
does not control the trailer brak-
ing system. Particular care is
therefore necessary on slippery
surfaces.
WARNING
Under no circumstances
should the hydraulic
braking system of the vehicle be
tampered with to control the
brakes of the trailer.
WARNING