2007 Acura RL display

The anti-lock brake system (ABS)
helpspreventthewheelsfrom
locking up, and helps you retain
steering control by pumping the
brakes rapidly, much f aster than a
person can do it.When the ABS indicator comes on,
you will also see a ‘‘CHECK ABS
SYSTEM’’ message in the multi-
inf ormation display. If this indicator comes on, the anti-
lock f unction of the braking system
has shut down. The brakes still work
like a conventional system, but
without anti-lock. You should have
your dealer inspect your vehicle as
soon as possible.
You will f eel a pulsation in the brake
pedal when the ABS activates, and
you may hear some noise. This is
normal: it is the ABS rapidly
pumpingthebrakes.Ondry
pavement, you will need to press on
thebrakepedalveryhardbeforethe
ABS activates. However, you may
feel the ABS activate immediately if
you are trying to stop on snow or ice.
Let the ABS work f or you by always
keeping f irm, steady pressure on the
brake pedal. This is sometimes
ref erred to as ‘‘stomp and steer.’’ The electronic brake distribution
(EBD) system, which is part of the
ABS, also balances the f ront-to-rear
braking distribution according to
vehicle loading.
You should never pump the brake pedal.
Anti-lock Brakes (ABS)
ABS Indicator
Driving
353
——
y
y
(yy

The radar sensor is located behind
the Acura emblem in the f ront grille.
If the emblem is covered with mud,
dirt, dead leaves, wet snow, etc., or if
you put a sticker on it, the CMBS will
automatically shut off, and the
CMBS indicator on the instrument
panel will come on. You will also see
a CHECK CMBS RADAR SENSOR
message on the multi-inf ormation
display f or about 5 seconds.Always keep the emblem clean. If it
gets dirty, clean it with water or a
mild detergent. Never use chemical
solvents or polishing powder.Do not allow anything to impact the
radar sensor or the emblem. If either
of these parts receives a strong
impact, turn off the system by
pressing the CMBS of f switch, and
have your vehicle checked by a
dealer. If the f ront grille ever needs
to be repaired, consult a dealer f irst.
There are three bolts on the sides of
the radar sensor. Do not tamper with
these bolts, or you may cause the
system to malf unction. If the f ront emblem or the radar
sensor ever needs to be removed,
take your vehicle to a dealer.
Collision Mitigation Brake System (CMBS)
Radar Sensor
356
EMBLEM
BOLTS
(Do not tamper)
——
y
y
(y
y

When the CMBS is on, the radar
sensor constantly scans for vehicles
ahead of you. This means that
driving on a ro ad with a few or no
vehicles could cause a CHECK
CMBS RADAR SENSOR message to
appear on the multi-information
display. This is normal and not a
cause for concern. The
radar sensor may not always
scan as intended. Here are two
examples:
Thetiresarenotcorrectly
maintained. Always make sure the
tire pressures are correct (see
page ), and that the tires are
the correct size and in good
condition (see Tires on page ).
Your
vehicle is tilted because of a
heavy load in the rear or from
modifications to the suspension.
Do not overload your vehicle (see
Carrying Cargo on page ), and
do not make any modifi cations to
the suspension (see Accessories
and Modifications on page ).
335
333
415 415
Collision Mitigation Brake System (CMBS)
Driving
357
——
y
y
(yy

If the system senses a likely collision
with a vehicle or object ahead of you,
it alerts you with an audible and a
visual alarm.The audible alarm is a constant
beeping sound; the visual alert is an
amber colored BRAKE message that
f lashes in the multi-inf ormation
display. If these alarms come on,
take the appropriate means to
prevent a collision (apply the brakes,
change lanes, etc.).To turn the CMBS off, press the
CMBS OFF switch on the dashboard
f or about 1 second. When you do this,
a beeper sounds, a CMBS indicator
on the instrument panel comes on,
and a CMBS OFF message appears
on the multi-information display. To
turn the system back on, press the
switch again for about 1 second.
Collision Alarm
CMBS OFF Switch
Collision Mitigation Brake System (CMBS)
358
CMBS OFF SWITCH
——
y

y
(yy

The CMBS will automatically
recover when these conditions are
improved.
Any of the conditions below can
cause the CMBS to shut of f . When
the system shuts off, the CMBS
indicator in the instrument panel
comes on, and a CHECK CMBS
SYSTEM message appears on the
multi-inf ormation display f or about 5
seconds.
An abnormal tire condition is
detected (wrong tire size, f lat tire,
etc.).
Extended of f -road or mountainous
driving.
Driving your vehicle with the
parking brake applied.
Driving your vehicle in bad
weather(rain,fog,snow,etc.).
A dirty emblem on the f ront grille.
When you turn the ignition switch to
the ON (II) position, the CMBS is
turned on if it was on previously.
Collision Mitigation Brake System (CMBS)
Automatic Shut Of f
Driving
359
——
y
y
(yy

The CMBS indicator normally comes
on under these conditions:
When you manually turn off the
system.
When the system shuts off
automatically.
When you drive in bad weather
(rain, snow, fog, etc.). When
the VSA system indicator
comes on (see page ).
When you turn the ignition switch
to the ON (II) position, the CMBS
indicator should come on f or a f ew
seconds, then go of f . If the
indicator comes on at any other
time and a CHECK CMBS
SYSTEM message appears on the
multi-inf ormation display, there is
a problem with the CMBS. You
can still drive your vehicle, but
CMBS will not be operating. Have
your vehicle checked by a dealer.
If anything covers the f ront grille
(dirt, mud, dry leaves, wet snow,
etc.).
This indicator comes on f or several
seconds when you turn the ignition
switch to the ON (II) position. It also
comesonandstaysonwhenyou
turn the CMBS off by pressing the
CMBS OFF switch.
To turn the CMBS back on, make
sure the vehicle is stopped and the
ignition switch is in the ON (II)
position, then press the CMBS OFF
switch f or about 1 second. 371
Collision Mitigation Brake System (CMBS)
CMBS Indicator
360
CMBS INDICATOR
——
y
y
(yy

Your vehicle is equipped with a tire
pressure monitoring system (TPMS)
that turns on every time you start the
engine and monitors the pressure in
your tires while driving.
Each tire has its own pressure
sensor. If the air pressure of a tire
becomes significantly low, the
sensor in that tire immediately sends
a signal that causes the low tire
pressure indicator in the
instrumental panel and the
appropriate tire position indicator on
thetirepressuremonitoronthe
multi-info rmation display (see page
)tocomeon. For
example, if you check and fill
your tires in a warm area, then drive
in extremely cold weather, the tire
pressure will be lower than
measured and could be underinflated
and cause the low tire pressure
indicator to come on. Or, if you
check and adjust your tire pressure
in cooler conditions, and drive into
extremely hot conditions, the tire
maybecomeoverinflated.However,
the low tire pressure indicator will
not come on if the tires are
overinflated.
When
the low tire pressure indicator
is on, one or more of your tires is
signifi cantly underinflated. The
multi-information display also shows
a ‘‘CHECK TIRE PRESSURE’’
message (see page ). You should
stop and check your tires as soon as
possible, and inflate them to the
proper pressu re as indicated on the
vehicl e’s tire information placard.
Driving on a significantly under-
inflated tire causes the tire to
ov erheat and can lead to tire failure.
Under-infl ation also reduces fuel
efficiency and tire tread life, and may
affect the vehicle’s handling and
stopping ability.
Becausetirepressure variesby
temperature and other conditions,
the low tire pressure indicator may
come on unexpectedly. Refer to page for tire inflation
guidelines.
367 367
415
CONT INUED
Low Tire Pressure
Indicator
Tire Pressure Monitoring System (TPMS)
Driving
365
——
y
y
(yy

CONTINUED
If any of the tires have low pressure,
the multi-information display will
show a ‘‘CHECK TIRE PRESSURE’’
message. You will also see one or
more low pressure tire positions
blinking in the display (see page
).
If
there is a system error with the
TPMS, the multi-info rmation display
showsa‘‘SYSTEMFUNCTION
ERROR’’ message (see page ),
and the tire pressure readings will
not be displayed. You will also see a
‘‘CHECK TPMS SYSTEM’’ message
on the multi-information display (see
page ).
When
all tire pressures are normal,
the multi-information display will
show ‘‘TIRE PRESSURE OK
SYSTEM FUNCTION NORMAL.’’
When any of the tires has low
pressure, the multi-info rmation
display shows a ‘‘TIRE PRESSURE
ERROR SYSTEM FUNCTION
NORMAL’’ message (see page ).
76 79
369 79
Tire Pressure Monitoring System (TPMS)
Tire Pressure Monitor
Driving
367
VEHICLE ICON
——
y
y
(yy