2007 Acura MDX mode

When the main menu is blank,
SH-AWD or TIRE PRESSURE,
pressing the SEL/RESET button
changes the display to ‘‘trip meter/
odometer’’ ‘‘outside temperature/
odometer’’ and ‘‘engine oil lif e/
odometer’’.The odometer shows the total
distance your vehicle has been
driven. It measures miles in U.S.
models and kilometers in Canadian
models. It is illegal under U.S.
federal law and Canadian provincial
regulations to disconnect, reset, or
alter the odometer with the intent to
change the number of miles or
kilometers indicated.This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it. There
are two trip meters: Trip A and Trip
B. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
To reset a trip meter, display it, and
then press and hold the SEL/RESET
button until the number resets to
‘‘0.0.’’
CONT INUED
Multi-Inf ormation Display
Trip Meter
Odometer
Inst rument s and Cont rols
75
ODOMETER TRIP METER
——y
y
()-yy

The temperature sensor is in the
front bumper. The temperatu re
reading can be affected by heat
reflection from the road surface,
engine heat, and the exhaust from
surrounding traffic. This can cause
an incorrect temperature reading
when your vehicle speed is under
19 mph (30 km/h). When you start
your trip, the sensor is not fully
acclimatized, therefore it may take
several minutes until the proper
te mperature is displayed.
In certain weather conditions,
temperature readings near freezing
(32°F, 0°C) could mean that ice is
forming on the road surface.
You can adjust the outside
temperature display (see page ).
This
shows the outside Fahrenheit
te mperature in U.S. models, and
Centigrade temperature in Canadian
models.
When
you reset Trip A, average fuel
economy A is reset at the same time.
When you reset Trip B, average fuel
economy B is reset.
In the customizing mode, you can set
Trip A and average fuel economy A
to reset at the same time when you
refuel your vehicle (see page ).
92
91
Outside Temperature
Multi-Inf ormation Display
76
OUTSIDE TEMPERATURE
U.S.
CANADA
——y


y
()-y
y

This shows the estimated distance
you can travel on the fuel rema ining
in the fuel tank. This distan ce is
estimated from the fuel economy
you received over the last several
miles(U.S.) or kilometers (Canada),
so it will vary with changes in speed,
traffic, etc.
This
shows your vehicle’s average
fuel economy in mpg (U.S. model s)
or liter/100 km (Canadian models)
since you last reset the Trip A or
Trip B.
You can customize the Trip A and
AVERAGE FUEL A reset condition
in the multi-information display (see
page ).
This shows the average speed you
are traveling in miles per hour (mph)
forU.S.modelsorkilometersper
hour (km/h) for Can adian models.
To reset the AVERAGE SPEED you
have traveled, press and hold the
SEL/RESET button until the
number resets. This
shows the time passed traveled
since you last reset it. When you turn
the ignition switch to the ON (II)
pos ition, ELAPSED TIME is reset.
If you want to reset the ELAPSED
TIME manually, go to the trip
computer’s ELAPSED TIME display,
andpressandholdtheSEL/RESET
button until the number resets.
You can customize the ELAPSED
TIME reset condition in the multi-
inf ormation display (see page ). 94
92
AVERAGE FUEL A/B
RANGE
A VERA GE SPEED EL A PSED T IME
Multi-Inf ormation Display
Inst rument s and Cont rols
79
——y

y
()-yy

When the main menu displays
‘‘Keyless Memory Settings ,’’ you
can customize some vehicle control
settings.
To enter the customizing mode,
press the SEL/RESET button. If
you turn the ignition switch to the
ACCESSORY (I) or the LOCK (0)
position, or move the shift lever out
of Park, the display will change to
the normal screen.
You can customize some vehicle
control settings for ‘‘DRIVER 1’’ and
‘‘DRIVER 2’’ separate ly. If ‘‘DRIVER
1’’ or ‘‘DRIVER 2’’ is not displayed,
cu stomizing is not possible.
To have the driver’s ID detected,
make sure your remote transmitter
is linked to the system (see Keyless
Memory Settings on page ).If
you want the settings as they were
when the vehicle left the factory,
select DEFAULT ALL, as described
on page .
Ref er to the table on the f ollowing
pages about the settings you want to
customize. If you want to change any vehicle
control settings, select CHG
SETTING, then press the SEL/
RESET button.
To change the settings, the ignition
switch must be in the ON (II)
position, and the vehicle must be
stopped with the transmission in
Park. 86
139TM
CONT INUED
Multi-Inf ormation Display
Customize Settings
Inst rument s and Cont rols
83
TM
—

—yy
()-yy

Î
Î
Î Î
Î
Î
Î
Î Î
Î
Menu Item Description
Group Setup Page Setting Option
INTERIOR LIGHT
DIMMING TIME
HEADLIGHT
AUTO OFF TIMER
AUTO LIGHT
SENSITIVITY
AUTO DOOR LOCK
AUTO DOOR UNLOCK
KEY AND REMOTE
UNLOCK MODE
KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK
TIMER
WIPER ACTION Changes
how long (in seconds) the interior lights
stay on after you close the doors and the tailgate.
Changes how long (in seconds) the exterior lights
stay on after you close the driver’s door.
Changes the timing of when the headlights come
on. The headlight switch needs to be in the AUTO
position.
Changes the setting of when to automatically lock
the doors.
Changes the setting of when to automatically
unlock the driver’s/all the doors.
Changes which doors unlock with the remote
transmitter in a first push.
The exterior lights flash each time you press the
LOCK or UNLOCK button. A beeper will also
sound when you press the LOCK button twice.
Changes how long it takes (in seconds) for the
doors to relock and the security system to set after
you unlock but do not open the door.
Changes the wiper operation between two settings
when the wiper switch is in the INT position.
Set/ Cancel all the customized settings as default.
LIGHTING
SETUP
(P.100)
DOOR/WINDOW
SETUP
(P.105)
WIPER SETUP
(P.113)
DEFAULT ALL
(P.86) 101
102
103
106
107
109
110
111
113
86
60 sec
30 sec
60 sec
30 sec
15 sec
MAX
HIGH
MID
SHIFT FROM P
WITH VEH SPD
OFF
IGN OFF
OFF
DRIVER DOOR
ALL DOORS
ON
OFF
90 sec
60 sec
30 sec
INTERMITTENT
WITH VEH SPD
SET
CANCEL 15 sec
0sec
LOW
MIN
: Default setting
SHIFT TO P DRIVER DOOR/ ALL DOORS
Multi-Inf ormation Display
Inst rument s and Cont rols
85
——y


y
()-yy

ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button. When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
CUSTOMIZE ENTRY.
If the setting is not successf ully
completed, ‘‘FAILED’’ is shown f or
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display. To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.
DEFAUL T AL L
Multi-Inf ormation Display
86
——y


y
()-y
y

Û
Ý
ÛÝ
ÛÝ
LANGUAGE SELECTION
ADJUST OUTSIDE TEMP.
DISPLAY
TRIP A & AVG. FUEL RESET
with REFUEL
Here are the six custom settings for
the meter setup:
ADJUST ALARM VOLUME
ELAPSED TIME RESET
AUTO INTERIOR
ILLUMINATION
While METER SETUP is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( / ) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection.
CONT INUED
Meter Setup
Multi-Inf ormation Display
Inst rument s and Cont rols
89
INFO ( / )
BUTTON SEL/RESET
BUTTON
——y

y
()-yy

ÛÝÛÝ
CONT INUED
Adjust Outside Temp. Display
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions:
You can choose this customize item
f rom ‘‘METER SETUP’’ by pressing
the INFO ( / ) button repeatedly.Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ and repeat the procedure
again.
Multi-Inf ormation Display
Inst rument s and Cont rols
91
Canadian models
U.S. models
Canadian models
U.S. models
——y

y
()-yy