2007.5 Peugeot 307 SW Dag Owner's Manual

114
CHECKS
CHECKS
Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the handbrake
should be adjusted, even
between services.
Have the system checked by a
PEUGEOT dealer.
Air filter and passenger
compartment filter
Particle emission filter
(Diesel)
It is imperative that the particle emis-
sion i lter is maintained in accordance
with the manufacturer's servicing sche-
dule, by a PEUGEOT dealer. Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Disc and drum wear status
For any information relating to
the wear status of the surfaces
of the discs and drums, contact a
PEUGEOT dealer. Only use products recom-
mended by PEUGEOT or
products of equivalent qua-
lity and characteristics.
To ensure best performance from
components as important as the
power steering and the braking sys-
tem, PEUGEOT selects and offers
quite specii c products.
To prevent damage to the electrical
units, high pressure washing to clean
the engine compartment is strictly

prohibited .
Oil filter
Used products
Avoid all prolonged contact of the
used oil with the skin.
Brake l uid is harmful to health and
very corrosive.
Note: following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional cases,
notice discharges of water vapour
at the exhaust on acceleration. This
has no effect on the behaviour of the
vehicle or on the environment.
Do not dispose of used oil,
brake l uid or coolant into
drains or onto the ground.
Empty the used oil into the
containers provided for this purpose
in the PEUGEOT network.
Battery
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Have the i lter elements
replaced regularly. If you
drive in dusty condi-
tions, change them twice
as often. Brake pads
It may be necessary to check
the thickness of the pads,
even between services.
Handbrake Change the i lter regularly,
in accordance with the ser-
vicing schedule.
Manual gearbox

To check the main levels
and certain components, in
accordance with the manu-
facturer's servicing sche-
dule, refer to the pages of
the servicing booklet which corres-
pond to your vehicle's engine.
This does not require an oil
change. Have the level checked
in accordance with the manu-
facturer's servicing schedule.

114
CHECKS
CHECKS
Where the handbrake travel
is too great or there is a re-
duction in the performance
of the system, the handbrake
should be adjusted, even
between services.
Have the system checked by a
PEUGEOT dealer.
Air filter and passenger
compartment filter
Particle emission filter
(Diesel)
It is imperative that the particle emis-
sion i lter is maintained in accordance
with the manufacturer's servicing sche-
dule, by a PEUGEOT dealer. Brake pad wear depends
on the style of driving, in
particular for vehicles which
are used in town, over short
distances.
Disc and drum wear status
For any information relating to
the wear status of the surfaces
of the discs and drums, contact a
PEUGEOT dealer. Only use products recom-
mended by PEUGEOT or
products of equivalent qua-
lity and characteristics.
To ensure best performance from
components as important as the
power steering and the braking sys-
tem, PEUGEOT selects and offers
quite specii c products.
To prevent damage to the electrical
units, high pressure washing to clean
the engine compartment is strictly

prohibited .
Oil filter
Used products
Avoid all prolonged contact of the
used oil with the skin.
Brake l uid is harmful to health and
very corrosive.
Note: following prolonged operation
of the vehicle at very low speed or at
idle, you may, in exceptional cases,
notice discharges of water vapour
at the exhaust on acceleration. This
has no effect on the behaviour of the
vehicle or on the environment.
Do not dispose of used oil,
brake l uid or coolant into
drains or onto the ground.
Empty the used oil into the
containers provided for this purpose
in the PEUGEOT network.
Battery
At the start of winter, have
your battery checked by a
PEUGEOT dealer.
Have the i lter elements
replaced regularly. If you
drive in dusty condi-
tions, change them twice
as often. Brake pads
It may be necessary to check
the thickness of the pads,
even between services.
Handbrake Change the i lter regularly,
in accordance with the ser-
vicing schedule.
Manual gearbox

To check the main levels
and certain components, in
accordance with the manu-
facturer's servicing sche-
dule, refer to the pages of
the servicing booklet which corres-
pond to your vehicle's engine.
This does not require an oil
change. Have the level checked
in accordance with the manu-
facturer's servicing schedule.

10
115
PRACTICAL INFORMATION
Parking the vehicle

 As far as possible, park the vehi-
cle on level, stable and non-slip-
pery ground.

 Apply the handbrake, switch off
the ignition and engage i rst or
reverse gear (position P for the
automatic gearbox). Access to the spare wheel

 Open the boot.

 Open the l ap using the lug to re-
lease the winch and gain access
to its control nut.

 Unscrew the nut fully, using the
wheelbrace 1 , to unroll the winch
cable.
Tools
The following tools are located:
- in the right-hand trim of the boot,

1. Wheelbrace.

2. Removable towing eye.

3. Socket for anti-theft bolts.
- in the holder in the centre of the spare wheel,

4. Jack with handle.

5. Centralising tool.

6. Bolt cover tool.
CHANGING A WHEEL

10
116
PRACTICAL INFORMATION

 Detach the wheel/holder assem-
bly from the rear of the vehicle.

 Take out the notched hook to re-
lease the wheel, as shown in the
illustration. Removing the wheel

 Slide the holder cover to gain ac-
cess to the tools.

 If necessary, place a chock under
the wheel diagonally opposite to
the one to be changed.

 Remove the trim, using the
wheelbrace 1 , pulling at the valve
passage hole (for vehicles i tted
with steel wheels).

 Loosen the wheel bolts (see §
"Special features of alloy wheels"
for vehicles i tted with alloy
wheels).
Note: you can use the other end
of the tool 6 to unscrew the wheel
bolts.
 Place the jack 4 in contact with
one of the four locating points A
on the sub-frame, the one which
is closest to the wheel to be
changed.

 Extend the jack 4 until its base
is in contact with the ground. En-
sure that the centre line of the
base of the jack is straight above
the locating point A used.

 Raise the vehicle

 Remove one bolt and install the
centralising tool 5 in its place.

 Unscrew the other bolts and re-
move the wheel.

10
117
PRACTICAL INFORMATION
Fitting a wheel

 Position the wheel using the cen-
tralising tool 5 to assist you.

 Tighten the bolts by hand and re-
move the centralising tool 5 .

 Partly tighten the bolts using the
wheelbrace 1 .

 Fold the jack 4 and remove it.

 Fully tighten the bolts using the
wheelbrace 1 .

 Replace the wheel trim, starting
by placing the wheel trim notch
opposite the valve, and press it
on using the palm of the hand.

 Put the corresponding tools in the
holder and secure its cover.

 Place the holder on the ground
and align the spare wheel on it.

 Pass the notched hook into the
holder cover.

 Rei t the wheel under the vehicle
tightening the winch control nut
using the wheelbrace 1 .

 Fully tighten and check that
the wheel is horizontally l ush
against the rear l oor .

 Close the l ap using the lug to
lock the winch.

 Store the rest of the tools in the
right-hand trim of the boot. For your safety, always
change the wheel:
- on level, stable, non-slippery ground,
- with the handbrake on and the ig- nition switched off,
- with i rst or reverse gear engaged (position P for the automatic gear-
box),
- with the vehicle chocked.

Never go underneath a vehicle that
is supported only by a jack (use a
ramp).

Never rei t the holder under the
vehicle without the spare wheel.

Do not use a screwdriver in place
of the wheelbrace to unwind or
wind the winch. Recommendations when using
the temporary spare wheel *
Your vehicle may be equipped with a
spare wheel which has a different rim
to the standard wheel.
After use, have it replaced as quickly
as possible.
Observe the following instructions in
order to avoid altering the behaviour
of the vehicle:
- do not exceed
50 mph (80 km/h) ,
- do not i t a wheel trim,
- drive with care,
- check the tyre pressure indicated on the label.
* According to model and country.
After changing the wheel:
- have the correct positioning of the
punctured wheel, the tightening
of the bolts and the tyre pressure
checked by a PEUGEOT dealer
as soon as possible,
- have the punctured tyre repaired and rei t it to the vehicle as soon
as possible,
- have the correct positioning of the spare wheel checked by a
PEUGEOT dealer.
Wheels i tted with the Tyre Under-
Inl ation Detection system
For further information refer to "Tyre
under-inl ation detection" in the safe-
ty section.

10
118
PRACTICAL INFORMATION
Bolt covers
Alloy wheel bolts are covered by
chrome trims.
Use the yellow tool 6 to remove the
trims before slackening the bolts. If your vehicle is i tted with a steel
spare wheel, when i tting it, it is
nor-
mal when tightening the bolts to no-
tice that the washers do not come
into contact with the rim. The spare
wheel is secured by the cone shape
of each bolt.
Fitting snow tyres
If you i t snow tyres mounted on steel
wheels onto your vehicle, it is es-
sential to use special bolts available
from your PEUGEOT dealer.
Special features of alloy
wheels
Fitting the spare wheel
Anti-theft bolts
If your wheels are i tted with an anti-
theft bolt (one per wheel), the chrome
trim must be removed before un-
screwing the bolt using the anti-theft
socket and the wheelbrace.
This anti-theft socket was given to
you on delivery of your vehicle along
with the duplicate keys and the con-
i dential card.
Make a careful note of the code
number engraved on the head of the
anti-theft socket. This will enable you
to obtain a duplicate socket from a
PEUGEOT dealer.

10
119
PRACTICAL INFORMATION
1. Dipped beam headlamps (H1-55 W or xenon bulb).

WARNING: RISK OF ELECTROCU-
TION
Xenon bulbs must be changed by a
PEUGEOT dealer.
2. Main beam headlamps (H7-55 W).

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Press the end of each securing
clip. Change the bulb.
When i tting the new bulb, ensure
that the direction notches are po-
sitioned correctly and the securing
clips are i xed properly.
 Reconnect the connector.

 Rei t the protective cover.
Front lights
In the engine compartment, on the
right-hand side, remove the style
trim * :
- press the centre of each plastic stud A ,
- remove each plastic stud,
- remove the style trim.
When you have i nished, do not for-
get to put everything back in place
correctly:
- position the style trim * ,
- rei t each plastic stud A by press-
ing on it. Handle the bulbs with a dry
cloth.
The headlamps are i tted
with polycarbonate glass
with a protective coating. Do not
clean them with a dry or abrasive
cloth, nor with a detergent or sol-
vent product.
Use a sponge and soapy water.
CHANGING A BULB
* According to engine.

10
120
PRACTICAL INFORMATION
3. Side lights (W 5 W).

 Remove the protective cover cor-
responding to the faulty bulb.

 Disconnect the connector.

 Remove the bulb and change it.
4. Direction indicators (PY 21 W amber).

 Turn the bulb holder a quarter of
a turn and remove it.

 Change the bulb.

Note : in certain climatic conditions
(low temperature, humidity), con-
densation inside the headlamp
glass is normal ; it disappears a few
minutes after the lights are switched
on. 5. Fog lamps (H11-55 W).
Contact a PEUGEOT dealer to have
these bulbs changed.

 Push the repeater forwards and
release it.

 Remove the repeater and change
it.
These can be obtained from a
PEUGEOT dealer.
Amber coloured bulbs, such
as the direction indicators,
must be replaced with bulbs
of identical specii cation and
colour.
Integrated direction indicator side
repeaters.