2006 YAMAHA TTR50 fuel cap

1 - 1
GEN
INFO
DESCRIPTION
EC100000
GENERAL INFORMATION
EC110000
DESCRIPTION
1 Engine stop switch
2 Starter lever (choke)
3 Main switch
4 Front brake lever
5 Throttle grip
6 Start switch
7 Fuel tank cap
8 Fuel tank
9 Rear brake pedal
0 Fuel cock
A Air cleaner
B Drive chain
C Shift pedal
D Front fork
E Reflector (For Canada)
NOTE:

The machine you have purchased may differ
slightly from those shown in the following.
 Designs and specifications are subject to
change without notice.
1
4
7
5
2 6
3
\b
8
EE
0\f
DC B
1

1 - 10
GEN
INFO
CONTROL FUNCTIONS
STARTER LEVER (CHOKE)
When cold, the engine requires a richer air/fuel
mixture for starting. A separate starter circuit,
which is controlled by the starter lever 1, sup-
plies this mixture.
Pull the lever out to open the circuit (for start-
ing) and push the lever in to close the circuit.
1
FUEL TANK CAP
Remove the fuel tank cap 1 by turning
counter-clockwise.
WARNING
Do not overfill the fuel tank. Avoid spilling
fuel on the hot engine.
1
SIDESTAND
This sidestand 1 is used to support only the
machine when standing or transporting it.
WARNING
 Never apply additional force to the side-
stand.
Hold up the sidestand before starting out.1

1 - 11
GEN
INFO
FUEL
Use regular gasoline. Always use fresh, name
brand gasoline.
WARNING
Do not overfill the fuel tank. Avoid spilling
fuel on the hot engine. Do not fill the fuel
tank above the bottom of the filler tube 1
as shown in the illustration or it may over-
flow when the fuel heats up later and
expands.
a Fuel level
CAUTION:
Use only unleaded gasoline. The use of
leaded gasoline will cause severe damage
to the engine internal parts such as valves,
piston rings, and exhaust system, etc.
Recommended fuel: For USA, AUS and NZ: Unleaded gasoline only
For CDN, EUROPE and ZA: Regular unleaded gasoline
only
Fuel tank capacity: Total: 3.1 L (0.68 Imp gal, 0.82 US gal)
Reserve: 0.4 L (0.09 lmp gal, 0.11 US gal)
FUEL

SPEC
2 - 2
Oil capacity:
Engine oil Periodic oil change 0.8 L (0.70 Imp qt, 0.85 US qt)
Total amount 1.0 L (0.88 Imp qt, 1.06 US qt)
Air filter: Wet element
Fuel: Type Unleaded gasoline only (USA, AUS and NZ) Regular unleaded gasoline only
(CDN, Europe and ZA)
Tank capacity 3.1 L (0.68 Imp gal, 0.82 US gal)
Reserve amount 0.4 L (0.09 Imp gal, 0.11 US gal)
Carburetor: Type VM11
Manufacturer MIKUNI
Spark plug: Type CR7HSA
Manufacturer NGK
Gap 0.6 ~ 0.7 mm (0.024 ~ 0.028 in)
Clutch type: Wet, multiple-disc and centrifugal automatic
Transmission: Primary reduction system Spur gear
Primary reduction ratio 67/18 (3.722)
Secondary reduction system Chain drive
Secondary reduction ratio 37/13 (2.846)
Transmission type Constant mesh, 3-speed
Operation Left foot operation
Gear ratio: 1st 39/12 (3.250) 2nd 33/19 (1.736)
3rd 28/23 (1.217)
Chassis: Frame type Steel tube backbone
Caster angle 25.50 °
Trail 34.0 mm (1.34 in)
Tire: Type With tube
Size (front) 2.50-10 4PR
Size (rear) 2.50-10 4PR
Manufacturer (front and rear) CHENG SHIN
Type (front and rear) KNOBBY
Tire pressure (front and rear) 100 kPa (1.00 kgf/cm
2, 14.2 psi)
Brake: Front brake type Drum brake
Operation Right hand operation
Rear brake type Drum brake
Operation Right foot operation
GENERAL SPECIFICATIONS
1
2
3
4
5
6

4 - 10
ENGCYLINDER HEAD
CYLINDER HEAD
Extent of removal: 1 Cylinder head removal
Extent of removal Order Part name Q ’ty Remarks
CYLINDER HEAD REMOVAL
Preparation for removal Seat assembly and fuel tank Refer to “FRONT FENDER, SEAT
ASSEMBLY AND FUEL TANK ” section.
Muffler Refer to “MUFFLER ” section.
Carburetor Refer to “CARBURETOR ” section.
Front wheel Refer to “FRONT WHEEL AND REAR
WHEEL ” section in the CHAPTER 5.
1 Plug cap/spark plug 1/1
2 Crankshaft end cover 1
3 Timing plug 1
4 Camshaft sprocket cover 1
5 Tappet cover 2
6 Camshaft sprocket bolt 1 Refer to “REMOVAL POINTS ”.
7 Timing chain tensioner cap bolt 1
1

4 - 47
ENGENGINE REMOVAL
ENGINE REMOVAL
(4)
NewNew
LS
T R..30 Nm (3.0 m • kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..30 Nm (3.0 m •
kg, 22 ft • Ib)
T R..48 Nm (4.8 m •
kg, 35 ft • Ib)
T R..7 Nm (0.7 m •
kg, 5.1 ft • Ib)
T R..10 Nm (1.0 m • kg, 7.2 ft • Ib)
(3)
10
4
1 6
2
9
3
11
7
5 8
Extent of removal:
1 Engine removal
Extent of removal Order Part name Q ’ty Remarks
ENGINE REMOVAL
Preparation for removal Hold the machine by placing the suitable stand under the frame.
Seat assembly, fuel tank air filter
case cover and air filter case Refer to
“FRONT FENDER, SEAT
ASSEMBLY AND FUEL TANK ” section.
Carburetor Refer to “CARBURETOR ” section.
Muffler Refer to “MUFFLER ” section.
Spark plug cap
Disconnect the AC magneto cou-
plers.
Disconnect the neutral switch
lead.
Starter motor Refer to “ELECTRIC STARTING SYS-
TEM ” section in the CHAPTER 6.