2006 YAMAHA T135 coolant level

TABLE OF CONTENTSSAFETY INFORMATION ..................1-1
DESCRIPTION ..................................2-1
Left view ..........................................2-1
Right view ........................................2-2
Controls and instruments.................2-3
INSTRUMENT AND CONTROL
FUNCTIONS.......................................3-1
Main switch/steering lock ................3-1
Indicator and warning lights ............3-2
Speedometer unit ...........................3-3
Fuel gauge ......................................3-3
Handlebar switches ........................3-3
Shift pedal .......................................3-4
Brake lever .....................................3-4
Brake pedal ....................................3-5
Fuel tank cap ..................................3-5
Fuel .................................................3-6
Catalytic converter ..........................3-6
Starter (choke) lever ........................3-7
Kickstarter .......................................3-7
Seat ................................................3-7
Helmet holders ...............................3-8
Storage compartment .....................3-8
Sidestand ........................................3-9
PRE-OPERATION CHECKS..............4-1
Pre-operation check list ..................4-2OPERATION AND IMPORTANT
RIDING POINTS................................. 5-1
Starting and warming up a
cold engine ................................. 5-1
Starting a warm engine .................. 5-2
Shifting ........................................... 5-2
Tips for reducing fuel
consumption ............................... 5-3
Engine break-in .............................. 5-3
Parking ........................................... 5-5
General note .................................. 5-6
PERIODIC MAINTENANCE AND
MINOR REPAIR................................. 6-1
Owner’s tool kit ............................... 6-1
Periodic maintenance and
lubrication chart .......................... 6-2
Removing and installing the
cowlings and panel ..................... 6-5
Checking the spark plug ................. 6-7
Engine oil and oil filter element ...... 6-9
Coolant ......................................... 6-11
Cleaning the air filter element ...... 6-13
Adjusting the carburetor ............... 6-14
Adjusting the engine idling
speed ........................................ 6-15
Adjusting the throttle cable
free play .................................... 6-15
Valve clearance ............................ 6-16
Tires ............................................. 6-16
Spoke wheels ............................... 6-18Checking the brake lever
free play .................................... 6-19
Adjusting the brake pedal
free play .................................... 6-19
Adjusting the rear brake light
switch ....................................... 6-20
Checking the front brake pads and
rear brake shoes ...................... 6-20
Checking the front brake
fluid level .................................. 6-21
Changing the brake fluid .............. 6-22
Drive chain slack .......................... 6-22
Cleaning and lubricating the
drive chain ................................ 6-23
Checking and lubricating the
cables ....................................... 6-24
Checking and lubricating the
throttle grip and cable ............... 6-24
Lubricating the brake lever .......... 6-25
Lubricating the brake pedal ......... 6-25
Checking and lubricating the
centerstand and sidestand ....... 6-25
Lubricating the
swingarm pivots ........................ 6-26
Checking the front fork ................. 6-26
Checking the steering .................. 6-27
Checking the wheel bearings ....... 6-27
Battery ......................................... 6-28
Replacing the fuse ....................... 6-29
Replacing a headlight bulb .......... 6-30U5YPE0E0.book Page 1 Wednesday, February 23, 2005 4:22 PM

PRE-OPERATION CHECKS
4-2
4
EAU15603
Pre-operation check list
ITEM CHECKS PAGE
FuelCheck fuel level in fuel tank.
Refuel if necessary.
Check fuel line for leakage.3-6
Engine oilCheck oil level in engine.
If necessary, add recommended oil to specified level.
Check vehicle for oil leakage.6-9
CoolantCheck coolant level in reservoir.
If necessary, add recommended coolant to specified level.
Check cooling system for leakage.6-11
Front brakeCheck operation.
If soft or spongy, have Yamaha dealer bleed hydraulic system.
Check brake pads for wear.
Replace if necessary.
Check fluid level in reservoir.
If necessary, add recommended brake fluid to specified level.
Check hydraulic system for leakage.6-20, 6-21
Rear brakeCheck operation.
Check pedal free play.
Adjust if necessary.6-20
Throttle gripMake sure that operation is smooth.
Check cable free play.
If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.6-15, 6-24
Control cablesMake sure that operation is smooth.
Lubricate if necessary.6-24
Drive chainCheck chain slack.
Adjust if necessary.
Check chain condition.
Lubricate if necessary.6-22, 6-23
U5YPE0E0.book Page 2 Wednesday, February 23, 2005 4:22 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-4
6
EAU18660
NOTE:

The air filter needs more frequent service if you are riding in unusually wet or dusty areas.


Hydraulic brake service
Regularly check and, if necessary, correct the brake fluid level.
Every two years replace the internal components of the brake master cylinder and caliper, and change the brake fluid.Replace the brake hoses every four years and if cracked or damaged.
22*Cooling systemCheck coolant level and vehicle for coolant leakage.√√√√ √
Change. Every 3 years
23*Front and rear brake
switchesCheck operation.√√√√√ √
24Moving parts and ca-
blesLubricate.√√√√ √
25*Throttle grip housing
and cableCheck operation and free play.
Adjust the throttle cable free play if necessary.
Lubricate the throttle grip housing and cable.√√√√ √
26*Air induction systemCheck the air cut-off valve, reed valve, and hose for dam-
age.
Replace any damaged parts if necessary.√√√√ √
27*Lights, signals and
switchesCheck operation.
Adjust headlight beam.√√√√√ √ NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (× 1000 km)
ANNUAL
CHECK
1 6 12 18 24
U5YPE0E0.book Page 4 Wednesday, February 23, 2005 4:22 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-11
6
CAUTION:
ECA10420
Before installing the engine oil drain
bolt, do not forget to install the O-
ring, compression spring, and oilstrainer in position.
9. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.CAUTION:
ECA11620


In order to prevent clutch slip-
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Donot use oils with a diesel speci-
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.


Make sure that no foreign mate-rial enters the crankcase.
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
11. Turn the engine off, and then
check the oil level and correct it if
necessary.
EAU20070
Coolant The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
EAU37510
To check the coolant level
The coolant level should be checked as
follows before each ride. In addition,
the coolant must be changed at the in-
tervals specified in the periodic mainte-
nance and lubrication chart.
1. Place the vehicle on the center-
stand.NOTE:

The coolant level must be checked
on a cold engine since the level
varies with engine temperature.


Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to theside can result in a false reading.
2. Check the coolant level in the cool-
ant reservoir.
Tightening torque:
Engine oil drain bolt:
32 Nm (3.2 m·kgf, 23 ft·lbf)
Recommended engine oil:
See page 8-1.
Oil quantity:
With oil filter element replacement:
0.90 L (0.95 US qt) (0.79 Imp.qt)
Without oil filter element replace-
ment:
0.80 L (0.85 US qt) (0.70 Imp.qt)
U5YPE0E0.book Page 11 Wednesday, February 23, 2005 4:22 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-12
6
NOTE:The coolant should be between theminimum and maximum level marks.3. If the coolant is at or below the minimum level mark, remove cowl-
ing A. (See page 6-5.)
4. Loosen the coolant reservoir cap retainer bolt, and then lift the re-
tainer upward.
5. Remove the coolant reservoir cap, and then add coolant to the maxi-
mum level mark.
CAUTION:
ECA10470

use only YAMAHA GENUINE
COLANT. Using coolan other than
recommended, could cause damage
to oil seal and o-rings, as whell
as to the cooling system.
If water has been used instead
of coolant, replace it with cool-
ant as soon as possible, other-
wise the engine may not be sufficiently cooled and the cool-
ing system will not be protected
against frost and corrosion.


If water has been added to the
coolant, have a Yamaha dealer
check the antifreeze content of
the coolant as soon as possible,
otherwise the effectiveness ofthe coolant will be reduced.WARNING
EWA10380
Never attempt to remove the radiatorcap when the engine is hot.
6. Install the coolant reservoir cap.
7. Place the coolant reservoir cap re- tainer in the original position, and
then tighten the bolt to the speci-
fied torque.
8. Install the cowling.
1. Maximum level mark
2. Minimum level mark
1. Coolant reservoir cap retainer bolt
2. Coolant reservoir cap retainer
3. Coolant reservoir capCoolant reservoir capacity (maximum
level): YAMAHA GENUINE COOLANT
0.28 L (0.30 US qt) (0.25 Imp.qt)
Tightening torque:Coolant reservoir cap retainer bolt: 7.0 Nm (0.7 m ·kgf, 5.1 ft ·lbf)
U5YPE0E0.book Page 12 Wednesday, February 23, 2005 4:22 PM

PERIODIC MAINTENANCE AND MINOR REPAIR
6-37
6Engine overheating
WARNING
EWA10400


Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.


After removing the radiator cap retaining bolt, place a thick rag, like a towel, over the radiator cap, and then
slowly rotate the cap counterclockwise to the detent to allow any residual pressure to escape. When the hissingsound has stopped, press down on the cap while turning it counterclockwise, and then remove the cap.
NOTE:If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolantas soon as possible.
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.The coolant level is low.
Check the cooling system
for leakage.
Have a Yamaha dealer checkand repair the cooling system.Add coolant. (See NOTE.)
Start the engine. If the engine overheats again,
have a
Yamaha dealer check
and repair the cooling system.
There is
leakage.
There is
no leakage.
U5YPE0E0.book Page 37 Wednesday, February 23, 2005 4:22 PM

SPECIFICATIONS
8-1
8
Dimensions:Overall length:1945 mm (76.6 in)
Overall width:
705 mm (27.8 in)
Overall height: 1065 mm (41.9 in)
Seat height: 770 mm (30.3 in)
Wheelbase:
1245 mm (49.0 in)
Ground clearance: 140 mm (5.51 in)
Minimum turning radius: 1900 mm (74.8 in)Weight:With oil and fuel:109,0 kg (240 lb)Engine:Engine type:Liquid cooled 4-stroke, SOHC
Cylinder arrangement:
Forward-inclined single cylinder
Displacement: 134.4 cm ³ (8.20 cu.in)
Bore × stroke:
54.0 × 58.7 mm (2.13 × 2.31 in)
Compression ratio:
10.90 :1
Starting system: Electric starter and kickstarter Lubrication system:
Wet sump
Engine oil:Type:
SAE20W40 or SAE20W50
Recommended engine oil grade: API service SF, SG type or higher
JASO MA
Engine oil quantity: Without oil filter element replacement:
0.80 L (0.85 US qt) (0.70 Imp.qt)
With oil filter element replacement: 0.90 L (0.95 US qt) (0.79 Imp.qt)Cooling system:Coolant reservoir capacity (maximum
level) YAMAHA GENUINE COOLANT: 0.28 L (0.30 US qt) (0.25 Imp.qt)
Radiator capacity (including all routes):
0.62 L (0.66 US qt) (0.55 Imp.qt)Air filter:Air filter element:Dry elementFuel:Recommended fuel:Regular unleaded gasoline only
Fuel tank capacity: 4.0 L (1.06 US gal) (0.88 Imp.gal)Carburetor:Manufacturer:MIKUNI
Type × quantity:
VM22 x 1
Spark plug (s):Manufacturer/model: NGK CPR8EA-9/ DENSO U24EPR-9
Spark plug gap:
0.8 –0.9 mm (0.031 –0.035 in)Clutch:Clutch type:
Wet, multiple-disc and centrifugal
automaticTransmission:Primary reduction system:
Spur gear
Primary reduction ratio: 69/24 (2.875)
Secondary reduction system: Chain drive
Secondary reduction ratio:
39/15 (2.600)
Transmission type: Constant mesh 4-speed
Operation: Left foot operation
Gear ratio:
1st:34/12 (2.833)
2nd:
30/16 (1.875)
3rd: 23/17 (1.353)
4th: 23/22 (1.045)Chassis:Frame type: Diamond
U5YPE0E0.book Page 1 Wednesday, February 23, 2005 4:22 PM

INDEXAAir filter element, cleaning..................... 6-13BBattery................................................... 6-28
Brake fluid, changing ............................ 6-22
Brake fluid level, checking .................... 6-21
Brake lever .............................................. 3-4
Brake lever free play, checking ............. 6-19
Brake lever, lubricating ......................... 6-25
Brake pads and shoes, checking .......... 6-20
Brake pedal ............................................. 3-5
Brake pedal free play, adjusting............ 6-19
Brake pedal, lubricating ........................ 6-25CCables, checking and lubricating .......... 6-24
Carburetor, adjusting ............................ 6-14
Care ........................................................ 7-1
Catalytic converter .................................. 3-6
Centerstand and sidestand,
checking and lubricating ..................... 6-25
Coolant.................................................. 6-11
Coolant temperature warning light .......... 3-2
Cowlings and panel, removing and
installing................................................ 6-5DDimmer switch ........................................ 3-4
Drive chain, cleaning and lubricating .... 6-23
Drive chain slack ................................... 6-22EEngine break-in ....................................... 5-3
Engine idling speed............................... 6-15
Engine oil and oil filter element ............... 6-9
Engine serial number .............................. 9-2
Engine, starting a warm .......................... 5-2
FFront fork, checking .............................. 6-26
Fuel......................................................... 3-6
Fuel consumption, tips for reducing........ 5-3
Fuel gauge.............................................. 3-3
Fuel tank cap .......................................... 3-5
Fuse, replacing ..................................... 6-29GGear position indicator lights .................. 3-2
General note ........................................... 5-6HHandlebar switches ................................ 3-3
Headlight bulb, replacing ...................... 6-30
Helmet holders ....................................... 3-8
High beam indicator light ........................ 3-2
Horn switch ............................................. 3-4IIdentification numbers ............................ 9-1
Indicator and warning lights .................... 3-2KKey identification number ....................... 9-1
Kickstarter............................................... 3-7MMain switch/steering lock........................ 3-1NNeutral indicator light .............................. 3-2PParking ................................................... 5-5
Part locations .......................................... 2-1
Periodic maintenance and
lubrication chart .................................... 6-2
Pre-operation check list .......................... 4-2RRear brake light switch, adjusting ......... 6-20Rear turn signal light and
tail/brake light...................................... 6-31
SSafety information ................................... 1-1
Seat ......................................................... 3-7
Shifting .................................................... 5-2
Shift pedal ............................................... 3-4
Sidestand ................................................ 3-9
Spark plug, checking ............................... 6-7
Specifications .......................................... 8-1
Speedometer unit .................................... 3-3
Starter (choke) lever................................ 3-7
Starting and warming up a
cold engine ........................................... 5-1
Start switch.............................................. 3-4
Steering, checking................................. 6-27
Storage.................................................... 7-3
Storage compartment.............................. 3-8
Swingarm pivots, lubricating ................. 6-26TThrottle cable free play, adjusting ......... 6-15
Throttle grip and cable, checking and
lubricating ........................................... 6-24
Tires ...................................................... 6-16
Tool kit..................................................... 6-1
Troubleshooting .................................... 6-35
Troubleshooting charts.......................... 6-36
Turn signal indicator light ........................ 3-2
Turn signal light bulb (front) or
auxiliary light bulb, replacing............... 6-31
Turn signal switch ................................... 3-4VValve clearance..................................... 6-16
Vehicle identification number .................. 9-1
U5YPE0E0.book Page 1 Wednesday, February 23, 2005 4:22 PM