2006 YAMAHA SLIDER 50 Owners Manual

SCOOTER CARE AND STORAGE
7
StorageShort-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover.
ECA00015
•
Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
•
To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strongchemicals are stored.Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
"Care" section of this chapter.
2. Drain the carburetor float
chamber by loosening the drain
bolt; this will prevent fuel deposits
from building up. Pour the drained
fuel into the fuel tank.
3. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
4. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit
sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap.
EWA00003
To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turningthe engine over.
5. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
6. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground.
Alternatively, turn the wheels a
little every month in order to
prevent the tires from becoming
degraded in one spot.
7-4

SCOOTER CARE AND STORAGE
77. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
8. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an
excessively cold or warm place
(less than 0 °C or more than 30
°C). For more information on
storing the battery, see page 6-19.
NOTE :
Make any necessary repairs beforestoring the scooter.
7-5

EAU01038
SPECIFICATIONS
Specifications ...................................................................................... 8-1
Conversion table ................................................................................. 8-4
8

SPECIFICATIONS
8
8-1 Model EW50
Dimensions:
Overall length 1,785 mm
Overall width 668 mm
Overall height 1,077 mm
Seat height 787 mm
Wheelbase 1,202 mm
Minimum ground clearance 185 mm
Minimum turning radius 1,800 mm
Weight:
Wet (with oil and a full fuel tank) 81 kg
Engine:
Engine type Air cooled, 2strokes
Cylinder arrangement Single cylinder, vertical
Displacement 49.2 cc
Bore x stroke 40.0 x 39.2 mm
Compression ratio 11.2:1
Starting system type Electric and kick starter
Lubrication system Separate lubrication
(Autolube)
Engine oil:
Type Yamalube 2
or 2 strokes engine oil
Classification Jaso FC or ISO EG-C, EG-D
Capacity 1.3 LFinal transmission oil:
Type SAE 10W30 type SE
Capacity 0.11L
Air filter type:Wet type element
Fuel:
Recommended fuel Regular unleaded gasoline
(RON 91 mini)
Fuel tank capacity 6.5 L
Carburetor:
Type/quantity TK ø12
Manufacturer TEIKEI
Spark plug:
Type / Manufacturer BR8HS / NGK or BR9HS/NGK
Spark plug gap 0.5—0.7 mm
Clutch type:Dry, centrifugal automatic
Transmission:
Primary reduction system Helical gear
Primary reduction ratio 52/13 (4.000)
Secondary reduction system Spur gear
Secondary reduction ratio 42/13 (3.230)
Transmission type V-belt automatic
Operation Centrifugal automatic type
Chassis:
Frame type Steel tube underbone
Caster angle 27°
Trail 90 mm
Specifications

SPECIFICATIONS
8
8-2 Tires:
Front:
Type Tubeless
Size / Manufacturer / model 120/80-12 55L / MICHELIN
/ BOPPER
120/80-12 55J / CHENG SHIN
/ MAXXIS
Rear:
Type Tubeless
Size / Manufacturer / model 130/90-10 61L / MICHELIN
/ BOPPER
130/90-10 61J / CHENG SHIN
/ MAXXIS
Maximum load * 184 kg
Air pressure (cold tire):
Up to 90 kg load*
Front 150 kpa
Rear 150 kpa
90 kg load—maximum load *
Front 150 kpa
Rear 170 kpa
* Total weight of rider, passenger, cargo and accessories
Minimum tire tread depth 1.6 mmWheels:
Front
Type Cast wheel/Aluminium
Size 12 X MT 2.75
Rear
Type Cast wheel/aluminium
Size 10 X MT 3.00
Brakes:
Front
Type Single disc brake
Operation Right hand operation
Type brake fluid DOT 4 or DOT 3
Rear
Type Drum brake
Operation Left hand operation
Suspension:
Front suspension Telescopic fork
Rear suspension Unit swing
Shock absorber:
Front fork type Coil spring/oil damper
Rear shock absorber Coil spring/oil damper
assembly type
Wheel travel:
Front wheel travel 104 mm
Rear wheel travel 100 mm

SPECIFICATIONS
8
8-3 Electrical:
Ignition system type C.D.I
Charging system Flywheel magneto
BatteryModel GM4-3B, YB4L-B, FB4-B
Voltage/capacity 12 V / 4 Ah
Headlight type:Bulb
Bulbs (voltage/wattage x quantity):
Headlight 12V, 35W/35Wx1
Tail/brake light 12V, 5W/21Wx1
Turn signal light
Front 12V, 10Wx2
Rear 12V, 10Wx2
Meter lights 12V, 1.2Wx2
High beam indicator light 12V, 2Wx1
Turn signal indicator light 12V, 2Wx1
Oil level warning light 12V, 2Wx1
Fuel level warning light 12V, 2Wx1
Fuses:
Main fuse 7A

SPECIFICATIONS
8
EAU04513
Conversion table






8-4