2006 YAMAHA RHINO 660 Switch

4-19 1. Light switch “OFF/ /”
1. Contacteur d’éclairage “OFF/ /”
1. Interruptor de luces “OFF/ /”
L
H
L
H
L
H
EVU00230
Switches
EVU00240
Light switch “OFF/ /”
Set the switch to “” to turn on the low beam and
the taillights.
Set the switch to “” to turn on the high beam
and the taillights.
Set the switch to “OFF” to turn off all the lights.CAUTION:_ Do not use the headlights with the engine
turned off for an extended period of time. The
battery may discharge to the point that the
starter motor will not operate properly. If this
should happen, remove the battery and re-
charge it. _
L
H
LH
EE.book Page 19 Monday, July 11, 2005 2:32 PM

4-21 1. On-Command four-wheel drive switch “2WD”/“4WD”
2. Differential gear lock switch “LOCK”/“4WD”
1. Contacteur de commande du mode de traction “2WD”/“4WD”
2. Contacteur de blocage du différentiel “LOCK”/“4WD”
1. Selector de tracción integral “2WD”/“4WD”
2. Selector de bloqueo del diferencial “LOCK”/“4WD”
EVU01272
On-Command four-wheel drive and differential
gear lock switches
This vehicle is equipped with an On-Command
four-wheel drive switch “2WD”/“4WD” and a differ-
ential gear lock switch “LOCK”/“4WD”. Select the
appropriate drive according to terrain and the con-
ditions.

Two-wheel drive (“2WD”): Power is supplied to
the rear wheels only.


Four-wheel drive (“4WD”): Power is supplied to
the rear and front wheels.


Four-wheel drive with the differential gear
locked (“4WD-LOCK”): Power is supplied to the
rear and front wheels when the differential gear
is locked (“DIFF.LOCK”). Unlike the 4WD
mode, all wheels turn at the same speed re-
gardless of traction.
EE.book Page 21 Monday, July 11, 2005 2:32 PM

4-25 1. Select lever
2. On-Command four-wheel drive switch “2WD”/“4WD”
1. Sélecteur
2. Contacteur de commande du mode de traction “2WD”/“4WD”
1. Palanca selectora
2. Selector de tracción integral “2WD”/“4WD”
On-Command four-wheel drive switch “2WD”/
“4WD”
To change from 2WD to 4WD, stop the vehicle,
and then set the switch to “4WD”. When the vehi-
cle is in 4WD, the 4WD indicator “” will come
on in the multi-function meter unit display. To
change from 4WD to 2WD, stop the vehicle, be
sure the select lever is set to position
a, and then
set the switch to “2WD”.
EE.book Page 25 Monday, July 11, 2005 2:32 PM

4-27 1. Differential gear lock switch “LOCK”/“4WD”
2. Select lever
1. Contacteur de blocage du différentiel “LOCK”/“4WD”
2. Sélecteur
1. Selector de bloqueo del diferencial “LOCK”/“4WD”
2. Palanca selectora
Differential gear lock switch “LOCK”/“4WD”
To lock the differential gear in 4WD, stop the vehi-
cle, make sure the On-Command four-wheel-drive
switch is set to “4WD”, move the select lever to po-
sition
b, and then set the switch to “LOCK”. When
the differential gear is locked, the differential gear
lock indicator light (“DIFF.LOCK”) will come on
along with the differential gear lock indicator “”
in the multi-function meter unit display. To release
the differential gear lock, stop the vehicle and set
the switch to “4WD”.
WARNING
Always ride at a slow speed when the vehicle
is in 4WD-LOCK, and allow extra time and dis-
tance for maneuvers.
All wheels turn at the same speed when the dif-
ferential is locked, so it takes more effort to
turn the vehicle. The amount of effort is more
the faster you go. You may lose control and
have an accident if you cannot make a sharp
enough turn for the speed you are traveling.
DIFF.
LOCK
EE.book Page 27 Monday, July 11, 2005 2:32 PM

4-29
NOTE:_

When the switch is set to “LOCK”, the differ-
ential gear lock indicator light will flash until
the differential gear is locked.


When the indicator light is flashing, turning
the steering wheel back and forth will help the
differential gear lock to engage.


Riding before the differential gear lock is
properly engaged (e.g., when the indicator
light is flashing) will cause the engine speed
to be limited until engagement is complete.
_
EE.book Page 29 Monday, July 11, 2005 2:32 PM

4-31 1. Horn switch “”
1. Contacteur d’avertisseur “”
1. Interruptor de la bocina “”
EVU01280
Horn switch “”
Press the switch to sound the horn.
EE.book Page 31 Monday, July 11, 2005 2:32 PM

4-63 1. Auxiliary DC jack cap
1. Capuchon de la prise pour accessoires
1. Tapa de la toma de corriente continua
1. Auxiliary DC jack
1. Prise pour accessoires
1. Toma de corriente continua
EVU00380
Auxiliary DC jack
The auxiliary DC jack is located at the right side of
the front panel.
The auxiliary DC jack can be used for suitable
work lights, radios, etc.
The auxiliary DC jack should only be used when
the engine is running.
1. Set the light switch to “OFF”.
2. Start the engine. (See pages 6-3–6-7.)
3. Open the auxiliary DC jack cap, and then in-
sert the accessory power plug into the jack.
4. When the auxiliary DC jack is not being used,
cover it with the cap. Maximum rated capacity for the auxiliary DC
jack:
DC 12 V, 120 W (10 A)
EE.book Page 63 Monday, July 11, 2005 2:32 PM

5-1
EVU01340
1-PRE-OPERATION CHECKS
Before using this vehicle, check the following points:
ITEM ROUTINE PAGE
BrakesCheck operation, free play, fluid level and fluid leakage.
Fill with DOT 4 brake fluid if necessary.5-7–5-9,
8-83–8-91
Parking brakeCheck for proper operation, condition and free play. 8-93–8-95
FuelCheck fuel level.
Fill with fuel if necessary.5-11–5-13
Engine oilCheck oil level.
Fill with oil if necessary.5-15, 8-23–8-33
Coolant reservoirCheck coolant level.
Fill with coolant if necessary.5-17–5-19,
8-47–8-49
Final gear oil/
Differential gear oilCheck for leakage. 5-21, 8-35–8-45
Accelerator pedalCheck for proper accelerator pedal operation. 5-23
Seat beltsCheck for proper operation and belt wear. 5-23
SteeringCheck for proper operation. 5-25
Fittings and fastenersCheck all fittings and fasteners. 5-25
Lights and switchesCheck for proper operation.5-25–5-27,
8-119–8-131
Wheels and tiresCheck tire pressure, wear and damage.5-29–5-35,
8-103–8-105
Axle bootsCheck for damage. 8-51
EE.book Page 1 Monday, July 11, 2005 2:32 PM