2006 YAMAHA BRUIN 250 oil

8-27
13. Add the specified amount of the recommend-
ed engine oil, then install and tighten the en-
gine oil filler cap.CAUTION:_

In order to prevent clutch slippage (since
the engine oil also lubricates the clutch),
do not mix any chemical additives. Do not
use oils with a diesel specification of “CD”
or oils of a higher quality than specified. In
addition, do not use oils labeled “ENERGY
CONSERVING II” or higher.


Make sure that no foreign material enters
the crankcase.
_
Recommended engine oil:
See page 10-2.
Oil quantity:
Without oil filter element removal:
1.50 L
With oil filter element removal:
1.60 L
EE.book Page 27 Friday, May 27, 2005 5:00 PM

8-29 1. Bolt A (× 6) 2. Bolt B (× 2)
1. Boulon A (× 6) 2. Boulon B (× 2)
1. Perno A (× 6) 2. Perno B (× 2)
14. Start the engine, and then let it idle for seve-
ral minutes while checking it for oil leakage. If
oil is leaking, immediately turn the engine off
and check for the cause.
15. Turn the engine off, and then check the oil
level and correct it if necessary.
16. Install the footboard by installing the bolts,
and then tightening them to the specified
torque.
17. Adjust the brake pedal free play. (See page
8-67.) Tightening torque:
Footboard bolt A:
3.8 Nm (0.38 m·kgf)
Footboard bolt B:
6.5 Nm (0.65 m·kgf)
EE.book Page 29 Friday, May 27, 2005 5:00 PM

8-31 1. Final gear oil
2. Correct oil level
3. Final gear oil filler bolt
1. Huile de transmission finale
2. Niveau d’huile correct
3. Boulon de l’orifice de remplissage du carter de transmission finale
1. Aceite de la transmisión final
2. Nivel de aceite exacto
3. Perno del orificio de llenado de aceite de la transmisión final
EBU11453
Final gear oil
Checking the final gear oil
1. Place the ATV on a level surface.
2. Remove the oil filler bolt, and then check the
oil level in the final gear case.NOTE:_ The oil level should be at the brim of the filler hole. _3. If the oil is below the brim of the filler hole,
add sufficient oil of the recommended type to
raise it to the correct level.CAUTION:_ Be sure no foreign material enters the final
gear case. _4. Install the oil filler bolt, and then tighten it to
the specified torque.
Tightening torque:
Final gear oil filler bolt:
23 Nm (2.3 m·kgf)
EE.book Page 31 Friday, May 27, 2005 5:00 PM

8-33 1. Final gear case cover 2. Bolt (× 2)
1. Couvercle du carter de transmission finale 2. Boulon (× 2)
1. Cubierta del cárter de la transmisión final 2. Perno (× 2)
1. Final gear oil drain bolt
1. Boulon de vidange du carter de transmission finale
1. Perno de drenaje del aceite del cárter de la transmisión final
Replacing the final gear oil
1. Remove the final gear case cover by remov-
ing the bolts.
2. Place the ATV on a level surface.
3. Place a container under the final gear case to
collect the used oil.
4. Remove the oil filler bolt and the drain bolt to
drain the oil.
5. Install the drain bolt, and then tighten it to the
specified torque.
6. Add the recommended final gear oil to the
brim of the filler hole. Tightening torque:
Final gear oil drain bolt:
23 Nm (2.3 m·kgf)
Recommended oil:
SAE 80 API GL-4 Hypoid gear oil
Oil quantity:
0.25 L
EE.book Page 33 Friday, May 27, 2005 5:00 PM

8-35
_CAUTION:
Be sure no foreign material enters the final
gear case. _7. Install the oil filler bolt, and then tighten it to
the specified torque.
8. Check for oil leakage. If oil leakage is found,
check for the cause.
9. Install the final gear case cover bolts, and
then tighten them to the specified torque. Tightening torque:
Final gear oil filler bolt:
23 Nm (2.3 m·kgf)
Tightening torque:
Final gear case cover bolt:
17 Nm (1.7 m·kgf)
EE.book Page 35 Friday, May 27, 2005 5:00 PM

8-45 1. Air filter element
1.Élément du filtre à air
1. Elemento del filtro de aire
1. Air filter element 2. Foam cover
1.Élément du filtre à air 2. Cache en mousse
1. Elemento del filtro de aire 2. Forro de espuma
3. Pull the air filter element out.
4. Remove the foam cover from the air filter ele-
ment.
5. Wash the foam cover gently but thoroughly in
water or solvent.
WARNING
_ When using solvent to clean the foam cover,
always use parts cleaning solvent. Never use
low flash point solvents or gasoline to clean
the foam cover because the engine could
catch fire or explode. _6. Squeeze the excess solvent out of the foam
cover and let it dry.CAUTION:_

Do not twist the foam cover when squeez-
ing it.


Do not apply oil to the foam cover.
_
EE.book Page 45 Friday, May 27, 2005 5:00 PM

8-61

Refill with the same type of brake fluid. Mixing
fluids may result in a harmful chemical reaction
and lead to poor brake performance.


Be careful that water does not enter the brake
fluid reservoir when refilling. Water will signifi-
cantly lower the boiling point of the fluid and
may result in vapor lock.


Brake fluid may deteriorate painted surfaces or
plastic parts. Always clean up spilled fluid im-
mediately.


Have a Yamaha dealer check the cause if the
brake fluid level goes down.
EBU11860
Brake fluid replacement
Complete fluid replacement should be done only
by trained Yamaha service personnel. Have a
Yamaha dealer replace the following components
during periodic maintenance or when they are
damaged or leaking.

Replace the oil seals every two years.


Replace the brake hoses every four years.
EE.book Page 61 Friday, May 27, 2005 5:00 PM

8-77
EBU00570
Cable inspection and lubrication
WARNING
Inspect cables frequently and replace if dam-
aged. Corrosion can result when the outer cov-
ering of control cables becomes damaged.
Cables can also become frayed or kinked. Op-
eration of controls could be restricted, which
could cause an accident or injury. Lubricate the inner cables and the cable ends. If
the cables do not operate smoothly, ask a Yamaha
dealer to replace them.
Recommended lubricant:
Engine oil
EE.book Page 77 Friday, May 27, 2005 5:00 PM