Page 8 of 14

SCIONPage 7
OPERATION
PASSIVE (AUTOMATIC) ARMING & DISARMING
When the xB -Security is programmed to PASSIVELYARM, the system will ARMafter the ignition key
is removed and all doors are closed; you do not need to lock the doors. When you come back to
your vehicle and open a door, you must insert the key into the ignition switch and turn it to “ON” dur-
ing the E
NTRYDELAY(0, 15 or 30 seconds), or an ALARMwill be TRIGGERED. If you lock the doors,
regular ARMINGwill override PASSIVEARMING; there will be no ENTRYDELAY. See the PROGRAM-
MING information on page 12 to activate the PASSIVEARMINGmode, as well as to select the ENTRYDELAYtime.
To P
ASSIVELYARMthe system:
Remove the key from the ignition switch.
Exit the vehicle, and close all the doors. (The system will not
A
RMwhile any of the doors are open.)
After the last door is closed:
The S
TATUSMONITOR’SLED turns on for 30 seconds,
then starts flashing. The system is now ARMED.
To D
ISARMthe PASSIVELYARMEDsystem:
Enter the vehicle through a front door.
The E
NTRYDELAYbegins:
The STATUSMONITOR’SLED turns on (no flashing.)
Insert the key into the ignition switch and turn it to “ON”before the ENTRYDELAYends.*
The LED turns off. The system is now DISARMED.
You may also D
ISARMthe system following any of the methods
described on page 6.
NOTE: If your vehicle’s tail and marker lights turn on for 2 seconds when the ignition key
is turned to “ON”, the T
RIGGERMEMORYwas activated; something TRIGGEREDan ALARMwhile you were away from the vehicle.
* If the E
NTRYDELAYtime elapses before the ignition switch is turned to “ON”, an ALARMwill be
TRIGGERED. To DISARMthe system during an ALARM, insert the ignition key and turn it to “ON”, or
press and release the remote control’s unlock button.
2
1THE SYSTEM ARMS 30
SECONDS AFTER THE
LAST DOOR
IS CLOSED
THE SYSTEM DISARMS
WHEN
YOU INSERT THE KEY
AND TURN IT TO “ON”
SCION
SECURITY
LIGHTS
FOR 30
SECONDS
(PRE-ARM-
ING)
THEN
STARTS
FLASHING
(SYSTEM
IS ARMED)
SCION
SECURITY
TURNS
ON (NO
FLASH-
ING)
DURING
THE
ENTRY
DELAY
21
Page 12 of 14

SCIONPage 11
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE
1. ARMthe system.
Press the LOCK button on the remote control or lock the doors
with the key.
(Remember, the system will not ARM if any door is open.)
2. Wait until the S
TATUSMONITOR’SLED starts flashing.
The LED will flash 30 seconds after the last door or hatch is closed.
3. Move inside the vehicle.
When movement occurs inside the vehicle, an alarm will be triggered
immediately. If sensor detects 2nd movement within 60 seconds after
the 1st warn away alarm trigger, then a regular ALARM activates for 60
seconds.
Note: If you find that the system does not perform as expected, contact
your Toyota dealer for more information.
4. D
ISARMthe system to stop the ALARM.
Press the UNLOCK button on the remote control or use the key to
DISARM the system.
RADAR SENSOR OFF MODE
THE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING:
1. Open the driver’s door .
The LED turns off. The system is now DISARMED.
2. Lock, then unlock the driver’s door inside lock button 3 times,
within 5 seconds.
The LED flash quickly.
3. Close the driver’s door.
4. ARM
THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THELEDIS
BLINKING.THE RADAR SENSOR WILL DEACTIVATE DURING ARMING.
NOTE: IF YOU DISARM THE SYSTEM AFTER YOU SET THE RADAR SENSOROFF, YOU HAVE TO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM
THE SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN.
THE SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF
MODE WHEN DISARMED.
SCION
SECURITY
Page 13 of 14

PROGRAMMING
The xB -Security is factory-set to not PASSIVELYARM. To change the system’s operation for PASSIVEARMINGoperation, as well as adjust the ENTRYDELAYtime, follow the procedure below. For more
information on this feature, please refer to page 7.
PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION1. Before you begin:
Open the driver’s door. Close the remaining doors
and the trunk or hatch. Unlock all doors with the inside
lock switch. Remove the key from the ignition switch.
Start the Programming Procedure. (Complete these steps within 40 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
Page 12 SCION
a. Close the driver’s
door.b.Lockandunlockall
doors3 timesby key
or remote control.
b.Lockthenunlockthe
driver’s door inside lock
button1 time.
a. Close, then Open the driver’s door:
2 times = PASSIVEARMINGOFF
3 times = PASSIVEARMINGON,
0 Sec. ENTRYDELAY4 times = PASSIVEARMINGON,
15 Sec. ENTRYDELAY5 times = PASSIVEARMINGON,
30 Sec. ENTRYDELAY
c. Open and close
the driver’s door.
c. The system locks the
door in 2 seconds; if this
does not happen, start
over. Programming is now
complete. e. Open the driver’s
door.d.Lock, then unlock
the driver’s door
inside lock button
3 times.
2. Insert and remove the key from
the ignition key cylinder 3
times; this must be completed
within 5 seconds.
f. The system locks the door
in 2 seconds; if this does
not happen, start over.g. Unlock the driver’s
door knob.