2006 TOYOTA xA Accessories, Audio & Navigation (in English)

PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTIONThe xA Security with RKE is factory-set to unlock the driver’s door when the UNLOCK button is
pressed on the remote control, then unlock the remaining doors when the UNLOCK button is
pressed again within 3 seconds. You may change the programming so all doors will unlock at once
when the UNLOCK button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.Page 16
SCION
SCION
Page 5
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Insertthe key into,
and removeit
from the ignition
switch 2 times.e. Insertthe key into
the ignition and
leave it in.
c. Insertthe key
into, and remove
it from the ignition
switch 1 time.g. Turnthe key from
LOCK to ON 4
times(ending at
LOCK.)h. Removethe key
from the ignition
switch.
i.The tail and marker lights flash 4times, the
buzzer chirps 4 times, and the doors lock
and unlock 4 times.
b. Close,then open
the driver’s door
2 times.f. Closethe driver’s
door.
d. Close, then open
the driver’s door
2 times.
When an alarm is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will lock the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys-
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The xA Security with RKE flashes the vehicle’s tail and marker lights
during REMOTE ARMING and REMOTE DISARMING, as well as during
an alarm. Also, the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the xA Security with RKE activates the vehicle’s horn.
If power tot the xA Security with RKE is disrupted while it is ARMED, an
alarm is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system.
The xA Security with RKE utilizes a PIEZO BUZZER, usually mounted
in the engine compartment, to sounds confirmation “chirps” and tones
for function confirmation and programming step confirmation.
The xA Security with RKE automatically locks your vehicle’s doors when
you turn the ignition key to “ON” or “START”, and unlocks the doors
when you turn the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
xA Security with RKE is approximately 50 feet. Please refer to page 10
for a description of factors that may affect the performance (operating
range) of the remote controls. STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED AUTO-
MATIC DOOR LOCK / UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES FUNCTIONS

PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTION (continued)3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4
SCION
SCION
Page 17
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Press and
releaseboth
LOCK and
UNLOCK
buttons at the
same time.
b. Press and
releasethe
UNLOCK button
once for all
doors unlock.
or Press and
releasethe
LOCK button
once for driver’s
door unlock.e.Open the driver’s
door;
programming is
now complete.
i.The tail and marker lights flash 1time, the
buzzer chirps 1time, and the doors lock and
unlock 1 time.
The xA Security with RKE will arm 30 seconds after the LOCK button on
the remote control is pressed, and DISARM when the UNLOCK button is
pressed. When the LOCK button is pressed, all the vehicle’s doors lock.
When the UNLOCK button is pressed, the driver’s door unlocks*, but if the
UNLOCK button is pressed again within 3 seconds, the remaining doors
unlock.
The xA Security with RKE will automatically RELOCK the vehicle’s doors if
no door is opened within 30 seconds after REMOTE DISARMING, the will
REARM 30 seconds later.
The xA Security with RKE will arm 30 seconds after you close and lock
the vehicle’s doors with the key, and will DISARM when you unlock a door
with the key.
The xA Security with RKE may be programmed to automatically arm 30
seconds after the ignition key is removed, the vehicle exited and the last
door and the trunk are closed, without the necessity of locking the doors.
The xA Security with RKE may be DISARMED with the vehicle’s ignition
key after it was PASSIVELY ARMED.
When the xA Security with RKE has been PASSIVELY ARMED, and
ENTRY DELAY (user-selectable at 0,15, or 30 seconds) will start when a
door is opened before an ALARM is TRIGGERED.
When you lock the vehicle with a central lock switch (while a door is open)
the xA Security with RKE will rm 30 seconds after you close all the doors
and the hatch (if open).
The xA Security with RKE may be DISARMED by inserting the key into
the ignition switch and turning it to “ON”.
Forcibly unlocking or opening a door or hatch while the xA Security with
RKE is ARMED will TRIGGER and ALARM immediately**. (If the system
was PASSIVELY ARMED, the ENTRY DELAY must pass before the
ALARM is TRIGGERED).
The xA-Security utilizes RADAR SENSOR.
The RADAR SENSOR works synchronize with vehicle theft deterrent sys-
tem.If somebody intrudes into the vehicle while the vehicle theft deterrent
system is set, the alarm blows the vehicle's horn intermittently and flashes
the emergency flashers.
Note
To prevent false alarms from triggered in case of following conditions:
•A child or pet is left in the vehicle.
•Any window or moon roof is left opened.
•When parking in the noisy area or in the roof parking.
•The vehicle body or glass is subjected to strong impact from the outside
(such as highly pressurized car wash).
•When transporting by car carrier.
•A cellphone in cup holder or center console covered storage is left in the
vehicle.
•When a bag on the seat in the vehicle,the detection area may change.
While ARMED, the xA Security with RKE monitors the ignition switch. If an
attempt is made to start the vehicle without a key, an ALARM is triggered. REMOTE ARMING /
DISARMING & LOCK-
ING / UNLOCKING
AUTOMATIC
REARMING
KEY
ARMING / DISARMING
PASSIVE
(AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY
DELAY
MANUAL ARMING
IGNITION KEY
DISARMING
POINT-OF-ENTRY
PROTECTION
RADAR SENSOR
IGNITION SWITCH
MONITORING
FEATURES FUNCTIONS* You may program the system to unlock all the doors with one press on the UNLOCK button.
See page 16 for programming instructions.
** The alarm will not trigger if the passenger side door is forcibly unlocked, until the passenger door is
opened.

REMOTE CONTROL INFORMATION
THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEMThe 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the
front and a P
ANIC
button on the back .
The xA Security with RKE may be controlled by as many as 4 remote controls, so you may add two
additional remote controls to the two included with your system. Contact your Scion dealer for more
details.
NOTE: This equipment has been tested and found to comply with the limits
for a class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try and correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
PROGRAMMINGIGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCKThe xA Security with RKE is factory-set to automatically lock your vehicle’s doors when you turn the
ignition key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or
“LOCK”. To change the programming of this feature, follow the procedure shown below.
1. Before you begin:
Open the driver’s door.
Remove the key from the ignition switch.
2. Start the Programming Procedure.(Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.
3. Select the Operating Mode and Complete the Programming Procedure.Page 18
SCION
SCION
Page 3
Front Button
Back Button
HOLD TO ACTIVATE
PANIC MODE
OPERATION
SCIONSECURITY
a.Insert the key into the
ignition switch and turn it
from LOCK to ON 5 times
(ending at ON).c.The S
TATUS
MONITOR
’SLED
turns on for 30 seconds.
b. Turnthe ignition
key back to lock.
a. Closethe door =
IG. Controlled Door LocksON
Close,then open and close
the door again= IG. Controlled
Door LocksOFFc.The tail and marker lights
flash once and the buzzer
chirps oncewhen the
system is set for IG door
lock control ON, twicefor
IG door lock control OFF.
If this does not happen,
start over. Programming is
now complete.
b.The tail and marker lights
flash once, and the buzzer
chirpsonce.
1
2
1
2
FLASHES WHEN
BUTTONS
PRESSED
PUSH TO LOCK
DOORS AND ARM
SYSTEM
PUSH TO UNLOCK
DOORS AND DIS
-
ARM SYSTEM

INTRODUCTIONCongratulations on your choice of the xA remote keyless security system to protect your vehicle! To
get the most from the system, we strongly recommend that you read this Owner’s Guide completely
to learn all of its features and functions.
The xA Security with RKE provides the convenience of remote keyless operation, enabling you to
ARM
and D
ISARM
at the same time you remotely lock and unlock the doors. The system provides
comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition
switch monitoring. While A
RMED
, the system will be T
RIGGERED
and sound an A
LARM
when a door is
forcibly unlocked or opened*, or when movement occurs inside the vehicle. During the A
LARM
, the
vehicle’s horn sounds and the headlights, tail lights and front marker lights flash.Also, the vehicle’s
starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the S
TATUS
MONITOR
for this system. Illustrated
below, this panel holds the LED indicator (for the system’s operating status) .
About the ignition-controlled automatic door locking/unlocking function.
The xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the key in the ignition switch to the “ON” or “START” position, and unlock them when you turn the
key back to the “ACC” or “LOCK” position. You may disable this feature by reprogramming the sys-
tem; refer to page 18 for programming information.
*When the system is P
ASSIVELY
(AUTOMATICALLY
) A
RMED
, there is an E
NTRY
DELAY
that will
elapse when a door is opened before an A
LARM
is T
RIGGERED
.
LIGHTS FOR30 SECONDS(PRE-ARMING
)
THEN STARTS
FLASHING(SYSTEM IS
ARMED
)
Page 2
SCION
SCION
Page 19
SCIONSECURITY
REMOTE CONTROL BATTERY REPLACEMENTThe following shows the procedure to replace the batteries in your remote controls. We recommend
that you replace the batteries at least once a year, or when the remote control’s transmitting range
diminishes. You may obtain the replacement battery from your Scion dealer, as well as many retail-
ers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement:
When replacing the battery, be careful not to lose the components.
Take care not to bend or damage the rubber gasket.REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5.Push the battery down and toward you, and hold it
down.
6. Pry the back edge of the battery up and toward you.
SCION
SECURITY
1
2
1
2

Page 20
SCION
To better understand the features and functions of this security system, please read this Owner’s
Guide completely prior to use. TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION – SECURITY WITH RKE FEATURES
4, 5
OPERATION
ARMING THE SECURITY (except PASSIVE ARMING) 6
DISARMING THE SECURITY (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING 10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION 11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE 14
RADAR SENSOR OFF MODE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION
21
REMOTE CONTROL BATTERY REPLACEMENTINSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to “snap” together.
SCION
Page 1

SCION
Page 21
Warning
•
This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do
not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.
•
To prevent accidents from occurring, keep the remote controls’ batteries out of the reach of chil-
dren. In the event a battery is swallowed, consult a physician immediately.
•
Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric
shock may result.
•
When replacing fuses, be sure to use fuses with the same specified capacity (amperage.)
Otherwise, damage to the unit or vehicle, fire or electric shock may result.
•
If an abnormal condition occurs, such as liquids spilling onto the product, or the product
emitting smoke or strange odors, stop using it immediately and consult the dealer from whom
you purchased the product. Continued use of the product before corrective actions are taken
may result in an accident, injury or fire.
•
Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation
may occur.Caution
•
Do not use batteries other than the type specified.
•
When placing batteries into the product, insert them as shown, paying close attention to the
polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and conta-
minate the surrounding area.
•
Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock
or injury may result.
•
Do not allow children to play with the remote controls. Otherwise, the doors may be locked or
unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.
•
If this product is dropped or its case is damaged, disconnect the power supply lead and
contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric
shock may result.

090002-28640700
Rev. A 04/11/05
SECURITY SYSTEM
xA - Security with RKEREMOTE KEYLESS SECURITY SYSTEM
DESIGNED SPECIFICALLY FOR YOUR VEHICLEOWNER’S GUIDE