2006 TOYOTA xA warning

Page 20
SCION
To better understand the features and functions of this security system, please read this Owner’s
Guide completely prior to use. TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION – SECURITY WITH RKE FEATURES
4, 5
OPERATION
ARMING THE SECURITY (except PASSIVE ARMING) 6
DISARMING THE SECURITY (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING 10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION 11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE 14
RADAR SENSOR OFF MODE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION
21
REMOTE CONTROL BATTERY REPLACEMENTINSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to “snap” together.
SCION
Page 1

PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTIONThe xA Security with RKE is factory-set to unlock the driver’s door when the UNLOCK button is
pressed on the remote control, then unlock the remaining doors when the UNLOCK button is
pressed again within 3 seconds. You may change the programming so all doors will unlock at once
when the UNLOCK button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.Page 16
SCION
SCION
Page 5
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Insertthe key into,
and removeit
from the ignition
switch 2 times.e. Insertthe key into
the ignition and
leave it in.
c. Insertthe key
into, and remove
it from the ignition
switch 1 time.g. Turnthe key from
LOCK to ON 4
times(ending at
LOCK.)h. Removethe key
from the ignition
switch.
i.The tail and marker lights flash 4times, the
buzzer chirps 4 times, and the doors lock
and unlock 4 times.
b. Close,then open
the driver’s door
2 times.f. Closethe driver’s
door.
d. Close, then open
the driver’s door
2 times.
When an alarm is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will lock the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys-
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The xA Security with RKE flashes the vehicle’s tail and marker lights
during REMOTE ARMING and REMOTE DISARMING, as well as during
an alarm. Also, the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the xA Security with RKE activates the vehicle’s horn.
If power tot the xA Security with RKE is disrupted while it is ARMED, an
alarm is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system.
The xA Security with RKE utilizes a PIEZO BUZZER, usually mounted
in the engine compartment, to sounds confirmation “chirps” and tones
for function confirmation and programming step confirmation.
The xA Security with RKE automatically locks your vehicle’s doors when
you turn the ignition key to “ON” or “START”, and unlocks the doors
when you turn the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
xA Security with RKE is approximately 50 feet. Please refer to page 10
for a description of factors that may affect the performance (operating
range) of the remote controls. STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED AUTO-
MATIC DOOR LOCK / UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES FUNCTIONS

ALARM INFORMATIONPANIC MODE OPERATIONWhen you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM
the P
ANIC
ALARM
by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC
ALARM
:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC
ALARM
at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM
TRIGGER
during the P
ANIC
ALARM
, the
regular A
LARM
takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa-
tion.
PANIC
Page 10
SCION
SCION
Page 11
MISCELLANEOUSDOOR AJAR WARNINGThe xA Security with RKE will sound a five second D
OOR
AJAR
WARNING
when you attempt to
R
EMOTE
ARM
the system while a door is open. To stop the warning tone, either close the open door,
or press and release the UNLOCK button on the remote control. To A
RM
the system, press the
LOCK button again.
Note: The D
OOR
AJAR
WARNING
will not sound when the hatch is open; the doors will lock,
but the system will not ARM
until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKINGThe xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or
“LOCK”. If you start the vehicle while a door is open, the system will not lock the doors; you must
lock them manually.
How the xA Security with RKE automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro-
gramming instructions.REMOTE CONTROL RANGEThe maximum range for the xA Security with RKE’s remote controls is 50 feet. However, several
factors that may affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
*As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.WITH ALL THE DOORS
CLOSED
, TURN THE KEY TO
THE“ON”
OR“LOCK”
POSITION
...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY
.
WHEN THE KEY IS TURNED
BACK TO THE
“ACC”
OR
“LOCK”
POSITION
...
ALL THE DOORS ARE
UNLOCKED
.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
MARKER LIGHTS
FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
1
1
1
1
PRESS THE
LOCK BUTTON
ON THE REMOTE
CONTROL
,
OR...
PRESS THE
PANIC BUTTON
AGAIN
, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL
, OR...
LOCK THE DOORS
WITH THE KEY
, OR...
UNLOCK A DOOR OR THE
TRUNK
WITH THE KEY

ALARM INFORMATIONPANIC MODE OPERATIONWhen you are confronted by a threatening situation, you may call attention to your vehicle by press-
ing the PANIC button on the back of the remote control. Unless you D
ISARM
the P
ANIC
ALARM
by
one of the described methods, it will continue for 60 seconds, then stop.
To activate the P
ANIC
ALARM
:
Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds.
The headlights flash repeatedly for 60 seconds.
The tail and marker lights flash repeatedly for 60 seconds.
The interior lights turn on for 60 seconds.
To disarm the Panic Alarm:
Do one of the following shown below.
You may activate a P
ANIC
ALARM
at any time, except when the key is in the ignition switch and
turned to the “ON” position. If the system detects an A
LARM
TRIGGER
during the P
ANIC
ALARM
, the
regular A
LARM
takes over. See ALARM INFORMATION on pages 12 and 13 for additional informa-
tion.
PANIC
Page 10
SCION
SCION
Page 11
MISCELLANEOUSDOOR AJAR WARNINGThe xA Security with RKE will sound a five second D
OOR
AJAR
WARNING
when you attempt to
R
EMOTE
ARM
the system while a door is open. To stop the warning tone, either close the open door,
or press and release the UNLOCK button on the remote control. To A
RM
the system, press the
LOCK button again.
Note: The D
OOR
AJAR
WARNING
will not sound when the hatch is open; the doors will lock,
but the system will not ARM
until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKINGThe xA Security with RKE is programmed to automatically lock your vehicle’s doors when you turn
the ignition key to “ON” or “START”, and unlock the doors when you turn the key back to “ACC” or
“LOCK”. If you start the vehicle while a door is open, the system will not lock the doors; you must
lock them manually.
How the xA Security with RKE automatically locks and unlocks the doors:
This feature may be defeated by changing the system’s programming. Refer to page 18 for pro-
gramming instructions.REMOTE CONTROL RANGEThe maximum range for the xA Security with RKE’s remote controls is 50 feet. However, several
factors that may affect your remote control’s actual performance, include, but are not limited to:
The remote control’s battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the system’s antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
*As the REMOTE CONTROL’s battery becomes weaker, the LED indicator becomes dimmer.
When you notice the LED becoming dimmer, you should replace the battery.WITH ALL THE DOORS
CLOSED
, TURN THE KEY TO
THE“ON”
OR“LOCK”
POSITION
...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY
.
WHEN THE KEY IS TURNED
BACK TO THE
“ACC”
OR
“LOCK”
POSITION
...
ALL THE DOORS ARE
UNLOCKED
.
THE HORN SOUNDS
FOR
60 SECONDS
HEADLIGHTS FLASH
FOR
60 SECONDS
MARKER LIGHTS
FLASH
FOR
60 SECONDS
TAIL LIGHTS FLASH
FOR
60 SECONDS
INTERIOR LIGHTS TURN ON FOR
60 SECONDS
1
1
1
1
1
PRESS THE
LOCK BUTTON
ON THE REMOTE
CONTROL
,
OR...
PRESS THE
PANIC BUTTON
AGAIN
, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL
, OR...
LOCK THE DOORS
WITH THE KEY
, OR...
UNLOCK A DOOR OR THE
TRUNK
WITH THE KEY

PROGRAMMINGDRIVER’S DOOR/ALL DOORS UNLOCK SELECTIONThe xA Security with RKE is factory-set to unlock the driver’s door when the UNLOCK button is
pressed on the remote control, then unlock the remaining doors when the UNLOCK button is
pressed again within 3 seconds. You may change the programming so all doors will unlock at once
when the UNLOCK button is pressed by following the steps below.
1. Before you begin: 2. Start the Programming Procedure.
Open the driver’s door. (Complete these steps within 40 seconds.)
Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.Page 16
SCION
SCION
Page 5
BRIEF DESCRIPTION–xA SECURITY WITH RKE FEATURES
a. Insertthe key into,
and removeit
from the ignition
switch 2 times.e. Insertthe key into
the ignition and
leave it in.
c. Insertthe key
into, and remove
it from the ignition
switch 1 time.g. Turnthe key from
LOCK to ON 4
times(ending at
LOCK.)h. Removethe key
from the ignition
switch.
i.The tail and marker lights flash 4times, the
buzzer chirps 4 times, and the doors lock
and unlock 4 times.
b. Close,then open
the driver’s door
2 times.f. Closethe driver’s
door.
d. Close, then open
the driver’s door
2 times.
When an alarm is TRIGGERED, the system disables the vehicle’s
starter and prevents engine start until the system is reset (DISARMED).
During an alarm, the system will lock the doors if one is unlocked and
will continue to do so for the duration of the alarm.
The user is notified that an alarm occurred. Upon DISARMING the sys-
tem after an alarm was TRIGGERED, the vehicle’s tail and marker lights
will be turned on, and the BUZZER sounds for 2 seconds.
You may TRIGGER a PANIC ALARM by pressing the PANIC button on
the back of the remote control to draw attention to your vehicle. During
the PANIC ALARM, the head, tail and marker lights flash, and the horn
sounds but the starter is not disabled.
The xA Security with RKE flashes the vehicle’s tail and marker lights
during REMOTE ARMING and REMOTE DISARMING, as well as during
an alarm. Also, the headlights flash during an alarm.
When the system is REMOTE DISARMED, it turns on the interior lights
in the vehicle for 30 seconds, or until the key is inserted into the ignition
switch. It also turns them on during an alarm.
During an alarm, the xA Security with RKE activates the vehicle’s horn.
If power tot the xA Security with RKE is disrupted while it is ARMED, an
alarm is TRIGGERED once power is restored.
This panel houses the flashing LED that indicates the operating status
of the security system.
The xA Security with RKE utilizes a PIEZO BUZZER, usually mounted
in the engine compartment, to sounds confirmation “chirps” and tones
for function confirmation and programming step confirmation.
The xA Security with RKE automatically locks your vehicle’s doors when
you turn the ignition key to “ON” or “START”, and unlocks the doors
when you turn the key back to “ACC” or “LOCK”.
The buzzer sounds for 5 seconds when you attempt to REMOTE ARM
the system while a door is open. You can stop the warning by closing
the door, or by pressing the UNLOCK button on the remote control.
The maximum operating range for the remote controls included with the
xA Security with RKE is approximately 50 feet. Please refer to page 10
for a description of factors that may affect the performance (operating
range) of the remote controls. STARTER DISABLE
FORCED LOCK DURING ALARM
TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION
POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION-CONTROLLED AUTO-
MATIC DOOR LOCK / UNLOCK
DOOR AJAR WARNING
REMOTE CONTROL
TRANSMITTER RANGE
FEATURES FUNCTIONS

Page 20
SCION
To better understand the features and functions of this security system, please read this Owner’s
Guide completely prior to use. TABLE OF CONTENTS
DESCRIPTION PAGE
INTRODUCTION
2
REMOTE CONTROL INFORMATION
THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTION – SECURITY WITH RKE FEATURES
4, 5
OPERATION
ARMING THE SECURITY (except PASSIVE ARMING) 6
DISARMING THE SECURITY (except PASSIVE DISARMING) 7
PASSIVE (AUTOMATIC) ARMING & DISARMING 8
AUTOMATIC REARMING 9
ARMING SUSPENSION 9
MISCELLANEOUS
DOOR AJAR WARNING 10
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10
REMOTE CONTROL RANGE 10
ALARM INFORMATION
PANIC MODE OPERATION 11
ALARM TRIGGERS 12
ALARM DESCRIPTIONS 13
STOPPING AN ALARM 13
RADAR SENSOR INFORMATION
RADAR SENSOR CHECK PROCEDURE 14
RADAR SENSOR OFF MODE 14
PROGRAMMING
PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15
DRIVER’S DOOR/ALL DOORS UNLOCK SELECTION 16, 17
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT
REMOVE THE BATTERY 19
INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION
21
REMOTE CONTROL BATTERY REPLACEMENTINSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can
interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the
battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to “snap” together.
SCION
Page 1

SCION
Page 21
Warning
•
This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do
not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.
•
To prevent accidents from occurring, keep the remote controls’ batteries out of the reach of chil-
dren. In the event a battery is swallowed, consult a physician immediately.
•
Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric
shock may result.
•
When replacing fuses, be sure to use fuses with the same specified capacity (amperage.)
Otherwise, damage to the unit or vehicle, fire or electric shock may result.
•
If an abnormal condition occurs, such as liquids spilling onto the product, or the product
emitting smoke or strange odors, stop using it immediately and consult the dealer from whom
you purchased the product. Continued use of the product before corrective actions are taken
may result in an accident, injury or fire.
•
Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation
may occur.Caution
•
Do not use batteries other than the type specified.
•
When placing batteries into the product, insert them as shown, paying close attention to the
polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and conta-
minate the surrounding area.
•
Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock
or injury may result.
•
Do not allow children to play with the remote controls. Otherwise, the doors may be locked or
unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.
•
If this product is dropped or its case is damaged, disconnect the power supply lead and
contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric
shock may result.