2006 SUZUKI SX4 transmission fluid

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-41
Transmission Warning Light Circuit Check – Light Remains “ON” at Ignition Switch ON (Non-Euro-
OBD Model)
S6RW0D5104054
Troubleshooting
Transmission Warning Light Circuit Check – Light Does Not Come “ON” at Ignition Switch ON (Non-
Euro-OBD Model)
S6RW0D5104055
TroubleshootingNon operate TCC (lock-
up) systemFaulty torque converterReplace.
Excessive “N”
→ “D” time
lagFaulty oil pumpInspect. If NG, replace.
Faulty forward clutchInspect. If NG, replace.
Faulty one-way No.2 clutchInspect. If NG, replace.
Leakage from “D” range fluid pressure
circuitOverhaul or replace valve body assembly.
Excessive “N”
→ “R” time
lagFaulty oil pumpInspect. If NG, replace.
Faulty reverse clutchInspect. If NG, replace.
Faulty 1st and reverse brakeInspect. If NG, replace.
Leakage from “R” range fluid pressure
circuitOverhaul or replace valve body assembly.
Poor engine brake in
downshift to “2” rangeFaulty O/D and 2nd coast brakeInspect. If NG, replace.
Poor engine brake in
downshift to “L” rangeFaulty 1st and reverse brakeInspect. If NG, replace. Condition Possible cause Correction / Reference Item
Step Action Yes No
1Diagnostic Trouble Code (DTC) Check
1) Check DTC referring to “DTC Check”.
Is there any DTC(s)?Perform DTC Flow to
repair and retry.Substitute a known-
good TCM and recheck.
If OK, substitute a
known-good
combination meter and
recheck.
Step Action Yes No
1Combination Meter Power Supply Check
1) Turn ignition switch ON.
Does other indicator / warning lights in combination meter
comes ON?Go to Step 2. Repair combination
meter power supply
circuit referring to
“Combination Meter
Circuit Diagram in
Section 9C”.
2 1) TCM power and ground circuit check referring to “TCM
Power and Ground Circuit Check”.
Is it in good condition?Go to Step 3. Repair or replace.
3DTC check
1) Check DTC referring to “DTC Check”.
Is there DTC U0073 or U0100?Go to applicable DTC
diag. flow.Go to Step 4.
4Combination Meter Function Check
1) Turn ignition switch ON.
Does A/T selector position indicator show correct select
lever position?Replace combination
meter.Substitute a known-
good TCM and recheck.

Downloaded from www.Manualslib.com manuals search engine 5A-46 Automatic Transmission/Transaxle:
Table for Step 4
DTC P0711: Transmission Fluid Temperature Sensor “A” Control Range / PerformanceS6RW0D5104048
Wiring Diagram
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory.
3) Start engine.
4) Start vehicle and increase vehicle speed to 40 km/h (25 mile/h) for 10 minutes or more.
5) Stop vehicle and check DTC.7 1) Check transmission range sensor referring to
“Transmission Range Sensor Inspection and
Adjustment”.
Are check results satisfactory?“RED/BLK”, “PNK/BLK”,
“RED”, “GRN/ORN”,
“GRN”, “GRN/YEL” or
“LT GRN/BLK” circuit
open or short to ground.
If wires and connections
are OK, substitute a
know-good TCM and
recheck.Replace transmission
range sensor. Step Action Yes No
Te r m i n a l
C07-20 C07-1 C07-8 C07-7 C07-19 C07-18
Select lever
positionP 8 – 14 V 0 V 0 V 0 V 0 V 0 V
R0 V8 – 14 V0 V0 V0 V0 V
N 0 V 0 V 8 – 14 V 0 V 0 V 0 V
D or 3 0 V 0 V 0 V 8 – 14 V 0 V 0 V
20 V0 V0 V0 V8 – 14 V0 V
L0 V0 V0 V0 V0 V8 – 14 V
5V
C06-11
C06-12
LT G R N
ORN
23
12 11
C06C07
[A]
1
I6RW0B510009-03
1. TCM 3. A/T
2. Transmission fluid temperature sensor [A]: Terminal arrangement of TCM connector (viewed from harness side)
DTC detecting condition Trouble area
Transmission temperature sensor signal is no change and
less than 20 °C (68 °F) while vehicle is running at 40 km/h
(25 mile/h) or more in vehicle speed for 10 minutes or more.• Transmission fluid temperature sensor or its circuit
malfunction
•TCM

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-47
DTC Troubleshooting
DTC P0712: Transmission Fluid Temperature Sensor Circuit LowS6RW0D5104022
Wiring Diagram
DTC Detecting Condition and Trouble AreaStep Action Yes No
1Was “A/T System Check” performed?Go to Step 2. Go to “A/T System
Check”.
2Inspect transmission fluid temperature sensor
1) Inspect transmission fluid temperature sensor referring
to “Transmission Fluid Temperature Sensor Inspection”.
Is result satisfactory?Go to Step 3 Replace transmission
fluid temperature
sensor.
3Check for transmission fluid temperature sensor circuit
1) Turn ignition switch to OFF position.
2) Disconnect valve body harness connector and TCM
connectors.
3) Check for proper connection to TCM at terminals “C06-
11” and “C06-12”. If connection is OK, check circuit for
open, short and high resistance for the following circuit.
• Between “C06-11” terminal of TCM connector and “LT
GRN” terminal of valve body harness connector.
• Between “C06-12” terminal of TCM connector and
“ORN” terminal of valve body harness connector.
Are they in good condition?Intermittent trouble or
faulty TCM. Check for
intermittent referring to
“Intermittent and Poor
Connection Inspection
in Section 00”. If OK,
substitute a known-
good TCM and recheck.Repair “LT GRN” and/or
“ORN” circuit.
5V
C06-11
C06-12
LT GRN
ORN
23
12 11
C06C07
[A]
1
I6RW0B510009-03
1. TCM 3. A/T
2. Transmission fluid temperature sensor [A]: Terminal arrangement of TCM connector (viewed from harness side)
DTC detecting condition Trouble area
Transmission temperature sensor terminal voltage is less
than specified value for 5 minutes or more after starting
engine.• Transmission fluid temperature sensor or its circuit
malfunction
•TCM

Downloaded from www.Manualslib.com manuals search engine 5A-48 Automatic Transmission/Transaxle:
DTC Confirmation Procedure
WARNING!
• When performing a road test, select a place where there is no traffic or possibility of a traffic
accident and be very careful during testing to avoid occurrence of an accident.
• Road test should be carried out with 2 persons, a driver and a tester, on a level road.

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory and start engine and keep for 20 minutes or more.
3) Stop vehicle and check DTC.
DTC Troubleshooting
DTC P0713: Transmission Fluid Temperature Sensor Circuit HighS6RW0D5104023
Wiring Diagram
DTC Detecting Condition and Trouble AreaStep Action Yes No
1Was “A/T System Check” performed?Go to Step 2. Go to “A/T System
Check”.
2Check transmission fluid temperature circuit for ground
short
1) Check continuity between terminal “C06-11” of
disconnected harness side TCM connector and ground.
Is continuity indicated?“LT GRN” circuit shorted
to ground.Go to Step 3.
3Inspect transmission fluid temperature sensor
1) Inspect transmission fluid temperature sensor referring
to “Transmission Fluid Temperature Sensor Inspection”.
Is result satisfactory?Intermittent trouble or
faulty TCM. Check for
intermittent referring to
“Intermittent and Poor
Connection Inspection
in Section 00”. If OK,
substitute a known-
good TCM and recheck.Replace transmission
fluid temperature
sensor.
5V
C06-11
C06-12
LT G R N
ORN
23
12 11
C06C07
[A]
1
I6RW0B510009-03
1. TCM 3. A/T
2. Transmission fluid temperature sensor [A]: Terminal arrangement of TCM connector (viewed from harness side)
DTC detecting condition Trouble area
Transmission fluid temperature sensor terminal voltage is
more than specified value even though engine was running in
“R”, “D”, “3”, “2” or “L” range for 12 minutes after starting
engine.• Transmission fluid temperature sensor or its circuit
malfunction
•TCM

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-49
DTC Confirmation Procedure
WARNING!
• When performing a road test, select a place where there is no traffic or possibility of a traffic
accident and be very careful during testing to avoid occurrence of an accident.
• Road test should be carried out with 2 persons, a driver and a tester, on a level road.

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory and start engine.
3) Increase engine coolant temperature to about 50 °C (122 °F) and more.
4) Start vehicle and increase vehicle speed to about 20 km/h (12 mile/h) for 10 minutes or more.
5) Stop vehicle and check DTC.
DTC Troubleshooting
Step Action Yes No
1Was “A/T System Check” performed?Go to Step 2. Go to “A/T System
Check”.
2Check transmission fluid temperature circuit for open
1) Turn ignition switch OFF.
2) Disconnect TCM connectors from TCM.
3) Check for proper connection to transmission fluid
temperature sensor at terminals “C06-11” and “C06-12”.
4) If OK, check continuity between terminals “C06-11” and
“C06-12” of disconnected harness side TCM connector.
Is continuity indicated?Go to Step 3. “LT GRN” or “ORN”
circuit open.
3Check transmission fluid temperature circuit for IG
short
1) Cool down A/T fluid temperature under ambient
temperature.
2) Connect TCM connectors to TCM with ignition switch
OFF.
3) Turn ignition switch ON.
4) Measure voltage between terminal “C06-11” of TCM
connector and ground.
Is it 4.6 V or more?“LT GRN” circuit shorted
to power circuit.
If circuit is OK, go to
St ep 4 .Intermittent trouble or
faulty TCM.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
If OK, substitute a
known-good TCM and
recheck.
4Inspect transmission fluid temperature sensor
1) Inspect transmission fluid temperature sensor referring
to “Transmission Fluid Temperature Sensor Inspection”.
Is result satisfactory?Intermittent trouble or
faulty TCM.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
If OK, substitute a
known-good TCM and
recheck.Replace transmission
fluid temperature
sensor.

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-53
DTC P0741 / P0742: TCC Circuit Performance or Stuck OFF / TCC Circuit Stuck ONS6RW0D5104026
DTC Detecting Condition and Trouble Area
DTC P0741
DTC P0742
DTC Confirmation Procedure
WARNING!
• When performing a road test, select a place where there is no traffic or possibility of a traffic
accident and be very careful during testing to avoid occurrence of an accident.
• Road test should be carried out with 2 persons, a driver and a tester, on a level road.

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory.
3) Start engine and warm it up to normal operating temperature.
4) Shift select lever to “N” and “D” range for each 10 seconds.
5) Drive vehicle with 3rd or 4th gear in “D” range and lock-up ON for 2 seconds or longer referring to “Automatic Gear
Shift Table”.
6) Shift select lever to “3” range.
7) Drive vehicle with 2nd or 3rd gear in “3” range, 15 – 30% throttle opening and at vehicle speed of 25 – 40 km/h (16
– 25 mile/h) at least for 1 second.
8) Stop vehicle and turn ignition switch OFF.
9) Repeat Step 3) to 7) one time.
10) Stop vehicle and check DTC.7Check output shaft speed sensor (VSS) gears visually
1) Check output shaft speed sensor gears for the
followings.
• No damage in drive gear on differential case
• No damage in driven gear in output shaft speed
sensor
Is result satisfactory?Intermittent trouble or
faulty TCM.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”.
If OK, substitute a
known-good TCM and
recheck.Replace drive gear and/
or driven gear of output
shaft speed sensor. Step Action Yes No
DTC detecting condition Trouble area
When driving vehicle with 3rd or 4th gear in “D” range,
difference in revolution between engine and A/T input (input
shaft speed) is larger than specification although TCM
commanded TCC solenoid valve to turn ON.• Mechanical malfunction of TCC solenoid valve
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Torque converter clutch malfunction
DTC detecting condition Trouble area
When driving vehicle with 2nd, 3rd or 4th gear in “D” range,
difference in revolution between engine and A/T input (input
shaft speed) is smaller than specification although TCM
commanded TCC solenoid valve to turn OFF.• Mechanical malfunction of TCC solenoid valve
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Torque converter clutch malfunction

Downloaded from www.Manualslib.com manuals search engine 5A-54 Automatic Transmission/Transaxle:
DTC Troubleshooting
DTC P0751 / P0752 / P0756 / P0757: Shift Solenoid MalfunctionS6RW0D5104027
DTC P0751: Shift Solenoid-A (No.1) Performance or Stuck OFF
DTC P0752: Shift Solenoid-A (No.1) Stuck ON
DTC P0756: Shift Solenoid-B (No.2) Performance or Stuck OFF
DTC P0757: Shift Solenoid-B (No.2) Stuck ON
DTC Detecting Condition and Trouble Area
DTC P0751
DTC P0752
DTC P0756
DTC P0757Step Action Yes No
1Was “A/T System Check” performed?Go to Step 2. Go to “A/T System
Check”.
2 1) Check TCC solenoid valve for operation referring to
“Solenoid Valves (Shift Solenoid Valves and Timing
Solenoid Valve) Inspection”.
Are they in good condition?Clean fluid passage or
replace valve body
assembly.Replace TCC solenoid
valve.
DTC detecting condition Trouble area
3rd gear ratio is detected although TCM command is for 2nd
gear while vehicle running at 20 km/h (12 mile/h) or more in
“D” range after engine being warmed up.• Mechanical malfunction of shift solenoid valve-A
(No.1)
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Mechanical malfunction of automatic transaxle
(clutch, brake or gear etc.)
DTC detecting condition Trouble area
2nd gear ratio is detected although TCM command is for 3rd
gear while vehicle running at 20 km/h (12 mile/h) or more in
“D” range after engine being warmed up.• Mechanical malfunction of shift solenoid valve-A
(No.1)
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Mechanical malfunction of automatic transaxle
(clutch, brake or gear etc.)
DTC detecting condition Trouble area
3rd gear ratio is detected although TCM command is for 4th
gear while vehicle running at 20 km/h (12 mile/h) or more in
“D” range after engine being warmed up.• Mechanical malfunction of shift solenoid valve-B
(No.2)
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Mechanical malfunction of automatic transaxle
(clutch, brake or gear etc.)
DTC detecting condition Trouble area
4th gear ratio is detected although TCM command is for 3rd
gear while vehicle running at 20 km/h (12 mile/h) or more in
“D” range after engine being warmed up.• Mechanical malfunction of shift solenoid valve-B
(No.2)
• Malfunction of valve body assembly
• Fluid passage clogged or leaking
• Mechanical malfunction of automatic transaxle
(clutch, brake or gear etc.)

Downloaded from www.Manualslib.com manuals search engine Automatic Transmission/Transaxle: 5A-55
DTC Confirmation Procedure
WARNING!
• When performing a road test, select a place where there is no traffic or possibility of a traffic
accident and be very careful during testing to avoid occurrence of an accident.
• Road test should be carried out with 2 persons, a driver and a tester, on a level road.

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory.
3) Start engine and warm it up to normal operating temperature.
4) Shift select lever to “N” and “D” range for 10 seconds.
5) Start vehicle and increase vehicle speed to 65 km/h (40 mile/h) with throttle position 10% or more.
6) Stop vehicle and turn ignition switch OFF.
7) Repeat Step 3) to 5) one time.
8) Stop vehicle and check DTC.
DTC Troubleshooting
DTC P0787: Shift / Timing Solenoid Control Circuit LowS6RW0D5104028
Wiring Diagram
DTC Detecting Condition and Trouble AreaStep Action Yes No
1Was “A/T System Check” performed?Go to Step 2. Go to “A/T System
Check”.
2 1) Check shift solenoid valve-A (No.1) or -B (No.2) for
operation referring to “Solenoid Valves (Shift Solenoid
Valves and Timing Solenoid Valve) Inspection”.
Are they in good condition?Clean fluid passage or
replace valve body
assembly.Replace shift solenoid
valve-A or -B.
12V
C06-14BLU/BLK
31
2
14
C06C07
[A]
I6RW0B510012-01
1. TCM 3. A/T
2. Timing solenoid valve [A]: Terminal arrangement of TCM connector (viewed from harness side)
DTC detecting condition Trouble area
Voltage of timing solenoid valve TCM terminal is low although
TCM is commanding timing solenoid valve to turn ON.• Timing solenoid valve circuit shorted to ground
• Timing solenoid valve malfunction
•TCM