2006 SUZUKI SX4 terminal

Downloaded from www.Manualslib.com manuals search engine 3B-5 Differential:
4WD Control System Wiring Circuit DiagramS6RW0D3201006
Terminal Arrangement of 4WD Control ModuleS6RW0D3201007
5V
5V
12V
G26-3
YEL
GRY
G26-2
G26-22G26-23REDWHT
G26-13
G26-14
G26-12
G26-11
G26-10BLK
WHT/RED
RED/BLK
GRY/YEL
RED/WHT
12V
L102-1
L102-4
1
37
9
10
12
13
14
12V
G26-21BLU
G26-25
G26-24ORN
BRN
5V
28
11
WHT
WHT
WHTWHTWHTWHT
WHT
RED
RED
RED
REDRED
RED
RED
46
5
L174-4BLK/ORNL174-5L174-1
I7RW01320001-01
1. Coupling assembly 6. ECM 11. Data link connector (DLC)
2. Coupling air temperature sensor 7. 4WD control module 12. “IG COIL” fuse
3. Combination meter 8. 2WD/4WD switch 13. “4WD” fuse
4. BCM 9. “4WD” switch 14. Main fuse box
5. ABS / ESP® control module 10. “4WD lock” switch
1 2 3 4 5 6 7 8 9 10 11 12
13 14 15 16 17 18 19 20 21 22 23 24 25 26
[A]
I4JA01332038-01
[A]: Connector “G26” viewed from harness side
Te r m i n a l C i r c u i t Te r m i n a l C i r c u i t
G26-2 Coupling assembly (power) G26-14 “4WD lock” switch
G26-3 Coupling assembly (ground) G26-21 Data link connector (DLC)
G26-10 Ground G26-22 CAN communication line (high)
G26-11 Power source for internal memory G26-23 CAN communication line (low)
G26-12 Power source G26-24 Coupling air temperature sensor (ground)
G26-13 “4WD” switch G26-25 Coupling air temperature sensor (power)

Downloaded from www.Manualslib.com manuals search engine 3B-11 Differential:
Visual InspectionS6RW0D3204004
Check the following parts and systems visually.
DTC CheckS6RW0D3204005
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(DLC) (1) located on underside of instrument panel.
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Read DTC according to instructions displayed on
SUZUKI scan tool and print it or write it down. Refer
to SUZUKI scan tool operator’s manual for further
details.
If communication between SUZUKI scan tool and
4WD control module is not possible, check if
SUZUKI scan tool is communicable by connecting it
to 4WD control module in another vehicle. If
communication is possible in this case, SUZUKI
scan tool is in good condition. Then check data link
connector and serial data line (circuit) in the vehicle
with which communication was not possible.
5) After completing the check, turn ignition switch OFF
and disconnect SUZUKI scan tool from data link
connector (DLC).
DTC ClearanceS6RW0D3204006
1) Turn ignition switch to OFF position.
2) Connect SUZUKI scan tool to data link connector
(DLC) (1) located on underside of instrument panel.
Special tool
(A): SUZUKI scan tool
3) Turn ignition switch to ON position.
4) Erase DTC according to instructions displayed on
SUZUKI scan tool. Refer to SUZUKI scan tool
operator’s manual for further details.
5) After completing clearance, turn ignition switch OFF
and disconnect SUZUKI scan tool from data link
connector (DLC).
6) Perform “DTC Check” and confirm that NO CODES
is displayed.
NOTE
DTC stored in 4WD control module memory
are also cleared in the following cases. Be
careful not to clear them before keeping their
record.
• When power to 4WD control module is cut
off (by disconnecting battery cable,
removing fuse or disconnecting 4WD
control module connectors).
• When the same malfunction (DTC) is not
detected again during 40 engine warm-up
cycles.

Inspection Item Referring
• Rear differential oil ---- level, leakage “Rear Differential Oil Change”
• Transfer gear oil ---- level, leakage “Transfer Oil Change in Section 3C”
• Manual transmission oil ---- level, leakage “Manual Transaxle Oil Change in Section 5B”
• Rear differential mounting(s) ---- wear and looseness
• Fuses ---- burning
• Battery ---- fluid level, corrosion of terminal “Battery Inspection in Section 1J”
• Connectors of electric wire harness ---- disconnection,
friction“Intermittent and Poor Connection Inspection in Section
00”
• Other parts that can be checked visually
1(A)I5RW0A320008-011(A)I5RW0A320008-01

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-16
4WD Position Indicator Remains ON Steady at Ignition Switch ONS6RW0D3204014
Wiring Diagram
Refer to “4WD Position Indicator Does Not Come ON at Ignition Switch ON but Engine Stops”.
Circuit Description
Transfer position indicator operates according to the signal from 4WD control module. If the 4WD control system is in
good condition, 4WD position indicator light up for 2 seconds when ignition switch is turned to ON position, and then
turned to OFF position. If an abnormality is detected in the system, 4WD position indicator remains lighting.
Troubleshooting3CAN communication circuit check
1) Check CAN communication circuit between combination
meter and 4WD control module referring to “DTC U0073:
Control Module Communication Bus Off”.
Is CAN communication circuit in good condition?Go to Step 4. Repair or replace.
4“METER” fuse check
1) Turn ignition switch to OFF position.
2) Check for fuse blown to “METER” fuse in junction block
assembly.
Is “METER” fuse in good condition?Go to Step 5. Replace “METER” fuse
and check for short.
5Combination meter power supply check
1) Remove combination meter referring to “Combination
Meter Removal and Installation in Section 9C”.
2) Check proper connection to “WHT/RED” and “BLK” wire
terminal of combination meter connector.
3) If OK, then turn ignition switch to ON position and
measure voltage between “WHT/RED” wire terminal of
combination meter connector and vehicle body ground.
Is it 10 – 14 V?Go to Step 6. “WHT/RED” wire is
open circuit.
6Combination meter ground circuit check
1) Turn ignition switch to OFF position.
2) Measure resistance between “BLK” wire terminal of
combination meter connector and vehicle body ground.
Is resistance 1
Ω or less?Substitute a known-
good combination meter
and recheck. If 4WD
position indicator still
remains OFF, substitute
a known-good 4WD
control module and
recheck.“BLK” wire is open or
high resistance circuit. Step Action Yes No
Step Action Yes No
1Check DTC
1) Check DTC referring to “DTC Check”.
Is there any DTC(s)?Perform DTC flow to
repair and retry.Go to Step 2.
2CAN communication circuit check
1) Check CAN communication circuit between combination
meter and 4WD control module referring to “DTC U0073:
Control Module Communication Bus Off”.
Is CAN communication circuit in good condition?Substitute a known-
good combination meter
and recheck. If 4WD
position indicator still
remains off, substitute a
known-good 4WD
control module and
recheck.Repair or replace.

Downloaded from www.Manualslib.com manuals search engine 3B-17 Differential:
DTC C1240: 4WD Control Module Power Supply Circuit MalfunctionS6RW0D3204015
Wiring Diagram
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Clear DTC using scan tool.
2) Turn ignition switch to ON position for 10 seconds.
3) Check DTC.
Troubleshooting
[A]: 4WD control module connector “G26” (viewed from harness side) 3. “4WD” fuse
1. 4WD control module 4. Main fuse box
2. “IG COIL” fuse
DTC detecting condition Trouble area
4WD control module power supply voltage is out of specification. 4WD control module power supply circuit
5V
5V
G26-12
G26-11
G26-10BLK
WHT/RED
RED/BLK
1
2
3
4
YEL
1 2 3
4 5
6 7 8 9 10 11
12
13
14 15 16
17 18 19
20
21 22
23
24 25 26
[A]
I7RW01320005-01
Step Action Yes No
1Was “4WD control system check” performed?Go to Step 2. Go to “4WD Control
System Check”.
24WD control module power circuit check
1) Disconnect 4WD control module connector with ignition
switch OFF.
2) Check for proper connection to “G26” terminal of 4WD
control module connector.
3) If connection is OK, measure voltage between “G26-11”
terminal of 4WD control module connector and vehicle
body ground with ignition switch ON.
Is it 10 – 14 V?Poor “G26-11”
connection or
intermittent trouble.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection in Section
00”. If wire and
connections are OK,
substitute a known-
good 4WD control
module and recheck.“4WD” fuse blown,
“WHT/RED” or “YEL”
wire is circuit open or
circuit short.

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-18
DTC C1243: Internal Circuit Malfunction of 4WD Control ModuleS6RW0D3204016
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Clear DTC using scan tool.
2) Start engine and run it for 10 seconds. or more.
3) Stop vehicle and check DTC.
Troubleshooting
Substitute a known-good 4WD control module and recheck.3Ground circuit check
1) Turn ignition switch to OFF position.
2) Check for proper connection to “G26-10” terminal of
4WD control module connector.
3) If OK, measure resistance between “G26-10” terminal of
4WD control module connector and vehicle body
ground.
If resistance 1
Ω or less?Substitute a known-
good 4WD control
module and recheck.Repair ground circuit. Step Action Yes No
DTC detecting condition Trouble area
Internal power supply malfunction of 4WD control module 4WD control module

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-20
Troubleshooting
Step Action Yes No
1Was “4WD control system check” performed?Go to Step 2. Go to “4WD Control
System Check”.
2Coupling air temperature sensor circuit check
1) Disconnect connector from coupling air temperature
sensor with ignition switch turned OFF.
2) Check for proper connection to “BRN” and “ORN”
terminals of coupling air temperature sensor connector.
3) If connection is OK, measure voltage between “BRN”
terminal of coupling air temperature sensor connector
and vehicle body ground with ignition switch turned ON.
Is it 4 – 6 V?Go to Step 3. Go to Step 5.
3Coupling assembly ground circuit check
1) Disconnect connector from 4WD control module with
ignition switch turned OFF.
2) Measure resistance between “ORN” terminal of coupling
air temperature sensor connector and “G26-24” terminal
of 4WD control module connector with ignition switch
turned OFF.
Is resistance below 5
Ω?Go to Step 4. “ORN” wire is open or
high resistance.
4Coupling air temperature sensor check
1) Check coupling air temperature sensor referring to
“Coupling Air Temperature Sensor Inspection”.
Is it in good condition?Substitute a known-
good 4WD control
module and recheck.Replace coupling air
temperature sensor.
5Coupling assembly circuit check
1) Disconnect connector from 4WD control module with
ignition switch turned OFF.
2) Check for proper connection to “G26-25” and “G26-24”
terminals of 4WD control module connector.
3) If connection is OK, measure resistance between “G26-
25” terminal of 4WD control module connector and
vehicle body ground.
Is resistance below 5
Ω?“BRN” wire is open or
high resistance circuit.Substitute a known-
good 4WD control
module and recheck.

Downloaded from www.Manualslib.com manuals search engine 3B-21 Differential:
DTC C1251: Coupling Air Temperature Sensor Circuit ShortS6RW0D3204018
Wiring Diagram
DTC Detecting Condition and Trouble Area
DTC Confirmation Procedure
1) Clear DTC using scan tool.
2) Turn ignition switch to ON position for 10 seconds.
3) Check DTC.
Troubleshooting
[A]: 4WD control module connector “G26” (viewed from harness side) 2. 4WD control module
1. Coupling air temperature sensor
DTC detecting condition Trouble area
Input signal from coupling air temperature sensor is lower than
specified value.• Coupling air temperature sensor
• Coupling air temperature sensor circuit
• 4WD control module
2
G26-25
G26-24ORN
BRN
5V
1
1 2 3
4 5
6 7 8 9 10 11
12
13
14 15 16
17 18 19
20
21 22
23
24 25 26
[A]
I7RW01320006-01
Step Action Yes No
1Was “4WD control system check” performed?Go to Step 2. Go to “4WD Control
System Check”.
2Coupling air temperature sensor circuit check
1) Disconnect connector from coupling air temperature
sensor with ignition switch turned OFF.
2) Check for proper connection to “BRN” and “ORN”
terminals of coupling air temperature sensor connector.
3) If connection is OK, measure voltage between “BRN”
terminal of coupling air temperature sensor connector
and vehicle body ground with ignition switch turned ON.
Is it 4 – 6 V?Go to Step 3. Go to Step 5.

Downloaded from www.Manualslib.com manuals search engine Differential: 3B-22
DTC C1252: Coupling Assembly Circuit OpenS6RW0D3204019
Wiring Diagram
DTC Detecting Condition and Trouble Area3Coupling assembly ground circuit check
1) Disconnect connector from 4WD control module with
ignition switch turned OFF.
2) Measure resistance between “ORN” terminal of coupling
air temperature sensor connector and “G26-24” terminal
of 4WD control module connector with ignition switch
turned OFF.
Is resistance above 1 M
Ω?Go to Step 4. “ORN” wire is shorted to
ground circuit.
4Coupling air temperature sensor check
1) Check coupling air temperature sensor referring to
“Coupling Air Temperature Sensor Inspection”.
Is it in good condition?Substitute a known-
good 4WD control
module and recheck.Replace coupling air
temperature sensor.
5Coupling assembly circuit check
1) Disconnect connector from 4WD control module with
ignition switch turned OFF.
2) Check for proper connection to “G26-25” and “G26-24”
terminals of 4WD control module connector.
3) If connection is OK, measure resistance between “G26-
25” terminal of 4WD control module connector and
vehicle body ground.
Is resistance above 1 M
Ω?“BRN” wire is shorted to
ground circuit.Substitute a known-
good 4WD control
module and recheck. Step Action Yes No
12V
G26-3
YEL GRY
G26-2
L102-1
L102-4 12
1 2 3
4 5
6 7 8 9 10 11
12
13
14 15 16
17 18 19
20
21 22
23
24 25 26
[A]
21
[B]
I7RW01320007-01
[A]: 4WD control module connector “G26” (viewed from harness side) 1. Coupling assembly
[B]: Coupling assembly connector “L102” (viewed from harness side) 2. 4WD control module
DTC detecting condition Trouble area
2WD/4WD switch is changed of 4WD lock position, and then
vehicle is not changed for more than 5 seconds.• Coupling assembly
• Coupling assembly circuit
• 4WD control module