2006 SUZUKI SX4 fuse box

Downloaded from www.Manualslib.com manuals search engine Wiring Systems: 9A-134
F-2 Anti-Lock Brake System Circuit DiagramS6RW0D910E034
2326
24
25
72
13E08
BLK
30A
ABS
SOL
40A
ABS
MOT11
WHT/REDWHT/BLU
GRN/WHT
8
BLK
R
RED
W
WHT
REDWHT
REDWHT
"A-8"
"A-5"
J/B10AABS
28
E3259
GRN/ORN
9
L315
L338
3
2
GRN/YEL
GRN/ORN
6
GW"D-7"
Brake light
switch
Individual circuit
fuse box (No.1)
1
GRN/BLK
GRN/YEL
3
G sensor
L371
E38715
G333
E38112
14
RED
R
112
WHT
W
B
BG311
A
A
RW
J/C
(CAN)(CAN)
Taiwan
(CAN)
9
IF EQPD
GRN/BLK
ABS
Cont.M
BCM
ECM
I6RW0C910A03-01

Downloaded from www.Manualslib.com manuals search engine Wiring Systems: 9A-136
F-4 Power Steering System Circuit DiagramS6RW0D910E036
P/S
Cont.M
60AP/S12
E32512
J/B10AIG1 SIG
26
RED
20
E377
E378
Torque sensor
BLK
E13
10
GRN
LT GRN/BLK
WHT
10
GRN
8
YEL
18
BLK
919
1
2 1E11
PPL
PPL
4
LT GRN/BLK
1
E377
E3784
PPL
G333
E381
E31
E13
E11 E11
Individual circuit
fuse box (No.1)
1 6 3 5 4
"C-2"
BCM
"A-8"P
GRY
GRY
5
7
GRY
G
11
12EF10
11EF
RHD
LHD
Except M16A engine M/T
M16A engine M/T
Except Taiwan
Taiwan ABCDEF
I6RW0C910A05-01

Downloaded from www.Manualslib.com manuals search engine 9B-13 Lighting Systems:
Illumination Cancel System Symptom Diagnosis (If Equipped)S6RW0D9204010
Interior Light Symptom DiagnosisS6RW0D9204011
NOTE
• Use of SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or
output side of BCM. For checking procedure, refer to “Diagnosis Using Output Test Function of
SUZUKI Scan Tool” under “Scan Tool Data in Section 10B”.
• Check each part in the order from the top of the following list.

DRL Operation Inspection (If Equipped)S6RW0D9204012
1) Confirm that lighting switch is in OFF position.
2) Confirm that dimmer and passing switch is in low beam position.
3) Check DRL for operation as follows.
a) Turn ignition switch to ON position and check headlights remain OFF.
b) Start engine and run it at idle speed. Check headlights turn ON at low beam.
c) Switch dimmer and passing switch to high beam position and check headlights remain turning ON at low
beam.
4) If check result is not as satisfied, go to “Inspection of DRL Controller and Its Circuits (If Equipped)”.
Inspection of DRL Controller and Its Circuits (If Equipped)S6RW0D9204013
1) Confirm that lighting switch is in good condition referring to “Headlight Switch (in Lighting Switch) Inspection”.
2) Confirm that oil pressure switch is in good condition referring to “Oil Pressure Switch Inspection in Section 9C”.
3) Remove glove box.
4) Remove DRL controller (1) from steering support member.
5) Connect connector to DRL controller.Condition Possible cause Correction / Reference Item
Illumination cancel do not
normal operationCircuit fuse blownReplace fuse and check for short circuit.
Illumination cancel switch faultyCheck illumination cancel switch referring to
“Illumination Cancel Switch Inspection (If
Equipped)”.
Combination meter and/or information
display faultyReplace combination meter and/or information
display.
Wiring or grounding faultyRepair circuit.
Condition Possible cause Correction / Reference Item
Dome light does not light
upBulb blownReplace bulb.
Circuit fuse blownReplace fuse and check for short circuit.
Dome light switch faultyCheck dome light switch.
Door switch faultyCheck door switch referring to “Door Switch
(Front / Rear Door) Inspection in Section 9C”.
Wiring or grounding faultyRepair circuit.
BCM faultyReplace after making sure that none of above
parts is faulty.
Luggage compartment
light does not light up (if
equipped)Bulb blownReplace bulb.
Rear end door switch faultyCheck switch referring to “Rear End Door
Switch Inspection in Section 9C”.
Wiring or grounding faultyRepair circuit.