2006 Seat Alhambra maintenance

Driving177
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a Control of the set speed is switched off if you reduce speed by depressing the
brake pedal. You can reactivate the control by pressing once on the upper part
of the rocker switch or button .
WARNING
It is dangerous to use a set speed which is too high for the prevailing road,
traffic or weather conditions. This may cause an accident.
Switching off system temporarily
Switching off the control temporarily in vehicles with a manual
gearbox
– Depress the brake or clutch pedal or
–Push the switch Ÿpage 176, fig. 133 to “OFF”, or
– Press the lower part of the button .
Switching off the control temporarily in vehicles with an automatic
gearbox
– Press the brake pedal or
– Select positions N or 1 or
–Push the switch Ÿpage 176, fig. 133 to “OFF”, or
– Press the lower part of the rocker button .
The speed stored will remain in the cruise control memory if the control is
switched off temporarily, unless you select positions N or 1. In this case, the
speed stored in the memory will be deleted.To resume the control function, release the brake or clutch pedal, move the
switch to ON or press the button Ÿpage 176, fig. 133 or button
Ÿpage 176, fig. 134 once.
WARNING
It is dangerous to use a set speed which is too high for the current road,
traffic or weather conditions. Risk of accident.
2%3 +
AA
CANCEL
AA
CANCEL
AA2%3 +

Intelligent technology179
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
Tips and Maintenance
Intelligent technology
Brakes
Brake servo
The brake servo supplements the pressure you exert on the brake pedal. It
works only when the engine is running.
If the brake servo does not operate, for example, when the vehicle is being
towed or due to a fault in the system, the brake pedal must be depressed
harder.
WARNING
The braking distance can also be affected by external factors.
•Never let the vehicle coast with the engine switched off. Failure to do so
could result in an accident. The braking distance is increased considerably
as the brake servo does not function.
•If the brake servo is out of action, for example if the car is being towed,
you will have to press the brake pedal considerably harder than normal.
Brake pads wear display I
If this light comes on, check the brake pads immediately.
At the same time, a text message or the necessary operations may appear on
the instrument panel .
WARNING
If the warning lamp lights up I or the corresponding message appears on
the instrument panel, immediately have the brake pads checked and
replaced, if necessary, at a specialised workshop.
Brake warning lamp H
If the warning lamp comes on, this may be caused by the
following reasons:
•With the handbrake on the warning light comes on H on the instrument
panel. If you are travelling at over 6 km/h with the hand brake on, a text
message or the required operations may appear on the instrument panel. In
addition a warning signal is heard.
•In the event of insufficient brake fluid the warning lamp lights up H on
the instrument panel. At the same time, a text message or the necessary oper-
ations may appear on the instrument panel . Stop the vehicle immediately
and check the level of the brake fluid Ÿpage 221
•In the event of a fault in the brake system the warning lamp lights up H
on the instrument panel and three buzzes are emitted. At the same time, a
text message or the necessary operations may appear on the instrument
panel . Stop the vehicle and do not drive on. You should obtain professional
assistance. This warning lamp
H can light up together with the anti-locking
brake system warning lamp JŸ.

Intelligent technology181
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a On braking sharply on slippery ground, this system helps to keep the vehicle
under control, as the wheels do not lock.
However, ABS will not necessarily guarantee shorter braking distances in all
conditions. The braking distance could even be longer if you brake on gravel
or on fresh snow covering a slippery surface.
WARNING
Try to always adapt the speed of the vehicle to weather, road and traffic
conditions. Do not let the extra safety afforded by the system tempt you
into taking any risks when driving. Risk of accident.
•The anti-lock brake system cannot defy the laws of motion. Slippery
and wet roads are dangerous even with ABS! If you notice that the ABS has
been activated, you should reduce speed immediately to suit the road and
traffic conditions.
•The ABS cannot reduce the risk of accident if, for example, you are
driving with an unsuitable load or too close to the preceding vehicle.
WARNING
•Modifications to the vehicle or work carried out incorrectly (e. g. to the
engine, the brake system, running gear or any components affecting the
wheels and tyres) could affect the efficiency of the ABS, EDL, ESP and TCS
and lessen their efficiency.
•The effectiveness of ABS is also determined by the tyres fitted
Ÿpage 225.
ABS warning lamp J
The warning lamp monitors the ABS.
The warning lamp Jshould light up for a few seconds when the ignition is
switched on. It goes out again after the system has run through an automatic
test sequence.
There is a fault in the ABS if:
•The ABS warning lamp J does not light up when the ignition is switched
on.
•The warning lamp does not go out again after a few seconds.
•The warning lamp lights up when the vehicle is moving.
The vehicle can still be braked in the normal way (except that the ABS control
function is out of action). Please take the vehicle to a qualified workshop as
soon as possible.
If a fault occurs in the ABS, the ESP warning lamp will also light up
42).
Brake system fault
If the ABS warning lamp
J lights up together with the brake warning lamp H, this indicates not only a fault in the ABS function, but also a possible fault
in the brake system Ÿ.
At the same time, a text message or the necessary operations may appear on
the instrument panel .
WARNING
Special care must be taken when working on the engine or on components
in the engine compartment.
•It is important that you read and observe the corresponding warnings
before working in the engine compartment Ÿpage 209.
42)Optional equipment

Intelligent technology183
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
•when driving in deep snow or on loose surfaces,
•when rocking the vehicle backwards and forwards to free it from mud, for
example.
You should press the button to switch the ESP back on when you no longer
need wheel spin.
When the ESP is deactivated, the TCS is switched off at the same time. This
means that this technology is not available for as long as the ESP remains
switched off.
How ESP works
ESP reduces the danger of skidding by braking the wheels individually. The
system uses the steering wheel angle and road speed to calculate the
changes of direction desired by the driver, and constantly compares them
with the actual behaviour of the car. If the desired course is not being main-
tained accurately (for instance if the car is beginning to skid) the ESP compen-
sates automatically by applying the brake at the appropriate wheel.
The forces acting on the braked wheel bring the car back to a stable condi-
tion. If the car is tending to oversteer (break away at the rear) the brake appli-
cation is concentrated on the outside front wheel; if the car is understeering
(tending to follow a wider radius in a bend), the brake is mainly applied to the
inside rear wheel.
How the Traction Control System (TCS) works
TCS reduces engine power to help prevent the driven wheels of front-wheel
drive vehicles losing traction during acceleration. The system works in the
entire speed range in conjunction with ABS. If a malfunction should occur in
the ABS, the TCS will also be out of action. TCS helps the car to start moving,
accelerate and climb a gradient in slippery conditions where this may other-
wise be difficult or even impossible.
When does the warning lamp light up or flash
?
•The warning lamp  lights up when the ignition is switched on and
should go out again after a few seconds.
•The warning lamp  will start flashing to indicate that the ESP and TCS
are counteracting an unstable driving condition.
•It  will light up continuously if there is a malfunction in the ESP.
•It will light up continuously if the ESP is switched off.
•It will also come on if a fault should occur in the ABS because the ESP
operates in conjunction with the ABS.
If the warning lamp
 lights up and stays on after the engine is started, this
may mean that the control system has temporarily switched off the function.
In this case the ESP can be reactivated by switching the ignition off and then
on again. If the warning lamp goes out, this means the system is fully func-
tional
If the battery is disconnected, the warning lamp
~ lights after turning the
ignition on. This should turn off after a brief trip.
WARNING
Try to always adapt the speed of the vehicle to weather, road and traffic
conditions. Do not let the extra safety afforded by the system tempt you
into taking any risks when driving. Risk of accident.
•The ESP and TCS cannot defy the laws of motion. This should be kept in
mind, particularly on slippery and wet roads and when towing a trailer.
•Always adapt your driving style to suit the condition of the roads and
the traffic situation.
•The ESP cannot reduce the risk of accident if, for example, you are
driving with an unsuitable load or too close to the preceding vehicle.
WARNING
•Modifications to the vehicle or work carried out incorrectly (e. g. to the
engine, the brake system, running gear or any components affecting the
wheels and tyres) could affect the efficiency of the ABS, EDL, ESP and TCS
and lessen their efficiency.

Driving and the environment185
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
Driving and the environment
Running-in
Running in a new engine
The engine needs to be run-in over the first 1,500 km.
Up to 1,000 kilometres
– Do not drive faster than three quarters of top speed.
– Do not use full throttle.
– Avoid high engine revolutions.
– Do not tow a trailer.
From 1000 to 1500 km
–Speeds can be gradually increased to the maximum road speed
or maximum permissible engine speed (rpm).
During its first few hours of running, the internal friction in the engine is
greater than later on when all the moving parts have bedded down.
For the sake of the environment
If the engine is run in gently, the life of the engine will be increased and its oil
consumption reduced.
Running in tyres and brake pads
New tyres should be run-in carefully for the first 500 km. New
brake pads should be run-in carefully for the first 200 km.
During the first 200 km, you can compensate for the reduced braking effect
by applying more pressure to the brake pedal. If you need to make an emer-
gency stop, the braking distance will be longer with new brake pads than with
brake pads which have been run-in.
WARNING
•New tyres do not give maximum grip to start with, and need running in.
This may cause an accident. Drive particularly carefully in the first 500 km.
•New brake pads must be “run in” and do not have the correct friction
properties during the first 200 km. However, you can compensate for the
slightly reduced braking effect by applying more pressure on the brake
pedal.
Braking effect and braking distance
The braking effect and braking distance are influenced by
driving situations and road conditions.
The efficiency of the brakes depends directly on the brake pad wear. The rate
of wear of the brake pads depends to a great extent on the conditions under
which the vehicle is operated and the way the vehicle is driven. If you often
drive in town traffic, drive short distances or have a sporty driving style, we
recommend that you have the thickness of your brake pads checked by SEAT
Service more frequently than recommended in the service schedule.

Driving and the environment187
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a
•Never park where the catalytic converter could come into contact with
dry grass or inflammable materials under the vehicle.
•Do not apply additional undercarriage protection or anti-corrosion coat-
ings to the exhaust pipes, catalytic converter or the heat shields on the
exhaust system, because the heat from the engine could ignite these.
Caution
Never fully drain the fuel tank, in this case, the irregularity of the fuel supply
may cause ignition problems. This allows unburnt fuel to enter the exhaust
system, which could cause overheating and damage the catalytic converter.
For the sake of the environment
Even when the emission control system is working perfectly, there may be a
smell of sulphur from the exhaust under some conditions. This depends on
the sulphur content of the fuel used. Quite often the problem can be reme-
died by changing to another brand of fuel.
Diesel particle filter
The diesel particle filter retains and burns the soot derived
from the combustion process.
The diesel particle filter system is made up of the following elements:
•Additive deposit with integrated pump
•Additive
•Diesel particle filter
•Lambda probeThe diesel particle filter removes practically all the particles of soot from the
exhaust gas. The filter retains these particles and burns them.
By adding additive automatically, the ignition temperature of the soot is
lowered. The additive is in a separate deposit and, after settling, is pumped
to the interior of the fuel tank The additive is also burned in the filter with the
soot, and so is not released into the atmosphere.
WARNING
The particle filter attains very high temperatures. Fire hazard!
•Never park where the catalytic converter could come into contact with
dry grass or inflammable materials under the vehicle.
•Do not apply additional underseal or anti-corrosion coatings to the
exhaust pipes, catalytic converter or the heat shields on the exhaust
system, because the heat from the engine could ignite them.
WARNING
The additive is toxic.
•If any work is required on the additive deposit, go to a specialized work-
shop because of the danger of toxicity.
•The additive should be stored in the closed original container in a safe
place out of reach of children. There is a toxic risk.
Caution
•Vehicles with the diesel particle filter should not use RME fuel (biodiesel)
as it may damage the fuel system.
•Using diesel fuel with a high sulphur count can reduce the working life of
the filter. Your SEAT dealership will be able to tell you which countries have
diesel with a high sulphur content.
WARNING (continued)

Driving and the environment 188
Driving abroad
Notes
For driving abroad, the following must be taken into consideration:
•For vehicles fitted with a catalytic converter ensure that unleaded petrol is
available for the journey. See the chapter “Refuelling”. Automobile organisa-
tions will have information about service station networks selling unleaded
fuel.
•In some countries it is possible that a vehicle model is sold under condi-
tions where some spare parts are not available or that the Authorised Service
Centre may only carry out limited repairs.
SEAT importers and distributors will gladly provide information about the
technical preparation of your vehicle in addition to necessary maintenance
and repair possibilities.
Adhesive strips for headlights
If you have to drive a right-hand drive vehicle in a left-hand drive country, or
vice versa, the asymmetric dipped beam headlights will dazzle oncoming
traffic.
To prevent dazzling, you must apply stickers to certain parts of the headlight
lenses. Further information is available from your Authorised Service
Centre.
Trailer towing
What do you need to bear in mind when towing a trailer?
The vehicle can, if suitably equipped, be used to tow a trailer or caravan.
If the car is supplied with a factory-fitted towing bracket it will already have
the necessary technical modifications and meet the statutory requirements
for towing a trailer. If you wish to retrofit a towing bracket Ÿpage 204.
Connectors
Your vehicle is fitted with a 12-pin connector for the electrical connection
between the trailer and the vehicle.
If the trailer has a 7-pin plug you will need to use an adapter cable. This is
available from SEAT Service
Trailer weight / draw bar loading
Never exceed the maximum permitted trailer weights. If you do not load the
trailer up to the maximum permitted trailer weight, you can then climb corre-
spondingly steeper gradients.
The maximum trailer weights listed are only applicable for altitudes up to
1,000 m above sea level. With increasing altitude the engine power and
therefore the vehicle's climbing ability are impaired because of the reduced
air density. The maximum trailer weight has to be reduced accordingly. The
weight of the vehicle and trailer combination must be reduced by 10% for
every further 1,000 m (or part thereof). Where possible, operate the trailer
with the maximum permitted draw bar weight on the ball joint of the towing
bracket, but do not exceed the specified limit.
The figures for trailer weights and draw bar weights given on the data plate
of the towing bracket are for certification purposes only. The correct figures
for your specific model, which may be lower than these figures for the towing
bracket, are given in the registration documents and “Technical data”.

Driving and the environment189
Safety FirstOperating instructionsTips and MaintenanceTe c h n i c a l D a t a Gross combination weight
The gross combination weight is the actual weight of the laden vehicle plus
the actual weight of the laden trailer . If the maximum permissible trailer
weight is to be utilized, the weight of the vehicle may have to be reduced.
Distributing the load
Distribute loads in the trailer so that heavy objects are as near to the axle as
possible. Loads carried in the trailer must be secured to prevent them
moving.
Tyre pressure
Set tyre pressure to the maximum permitted pressure shown on the sticker on
the inside of the tank flap. Set the tyre pressure of the trailer tyres in accord-
ance with the trailer manufacturer's recommendations.
Exterior mirrors
Check whether you can see enough of the road behind the trailer with the
standard mirrors. If this is not the case you should have additional mirrors
fitted. Both exterior mirrors should be mounted on hinged extension
brackets. Adjust the mirrors to give sufficient vision to the rear.
Headlight adjustment
If towing a trailer the dipped light may dazzle other drivers. Use the headlight
range control to lower the cone of light. If you do not have headlight range
control, have the headlights adjusted by a qualified dealership.
WARNING
•Never transport people in a trailer. This could result in fatal accidents.
•To avoid dazzling other drivers, adjust the dipped beam according to
the load. If not, an accident may occur.
•If using 225/45 R 17 94 W tyres for 7J x 17 wheels it is not permitted to
tow a trailer.
Note
•Towing a trailer places additional demands on the vehicle. We recom-
mend additional services between the normal inspection intervals if the
vehicle is used frequently for towing a trailer.
•Find out whether special regulations apply to towing a trailer in your
country.
Ball coupling of towing bracket
The removable ball coupling of the towing bracket is stored
with the tools on board behind the right-hand side trim of the
luggage compartment.
It is necessary to first tense the towing bracket removing the ball
coupling
Fig. 135 Location of
towing bracket