2006 SATURN ION Owners Manual

Removing the Spare Tire and Tools
The equipment you will need is located in the trunk.
Models with a 2.2L L4 or 2.4L Engine
1. Open the trunk. SeeTrunk on page 2-11for
more information.
2. Lift the trunk liner to access the spare tire and tools.
5-77
ProCarManuals.com

A. Cover
B. Retainer
C. Spare Tire
D. Wing Nut
E. Jack and Wheel Wrench
F. Bolt
3. Remove the retainer (B) that holds down the spare
tire. SeeCompact Spare Tire on page 5-90.
4. Remove the spare tire (C) by placing your hands at
the four and eight o’clock positions. Gently pull it up
and out of the trunk.
5. Remove the wing nut (D) that holds the jack and
remove the jack and wheel wrench (E).
5-78
ProCarManuals.com

Models with a 2.0L L4 Supercharged
Engine
1. Open the trunk. SeeTrunk on page 2-11for more
information.
2. Lift the trunk liner to access the spare tire and tools.
5-79
ProCarManuals.com

A. Retainer
B. Jack and Wheel Wrench
C. Spare Tire
D. Foam Support
E. Bolt
3. Remove the retainer (A) that holds down the jack,
wheel wrench (B) and spare tire (C).
4. Remove the spare tire by placing your hands at the
four and eight o’clock positions. Gently pull it up
and out of the trunk.
The tools you will be using include the jack (A) and
wheel wrench (B).
5-80
ProCarManuals.com

You will need to turn the plastic wheel nut
counterclockwise to loosen the wheel wrench from
the jack.Press the button and then pull on the end of the wheel
wrench to extend the handle.
5-81
ProCarManuals.com

Removing the Flat Tire and
Installing the Spare Tire
1. If your vehicle is equipped with plastic wheel
covers, use the wheel wrench to loosen the plastic
wheel nut caps.
Once you have loosened the plastic wheel nut caps
with the wheel wrench, you can nish loosening
them with your ngers. The plastic nut caps do not
come off. Using the at end of the wheel wrench,
pry along the edge of the wheel cover until it
comes off.
If your vehicle has aluminum wheels, rst remove
the center cap by pulling it out with the wheel
wrench.
2. Use the wheel wrench to loosen all the wheel nuts.
Do not remove them yet.
Notice:Make sure that the jack lift head is in the
correct position or you may damage your vehicle.
The repairs would not be covered by your warranty.
5-82
ProCarManuals.com

3. Position the jack lift head at the jack location
nearest the at tire. The front location is about
7 inches (17.8 cm) rearward from the front wheel
opening. The rear location is about 2 inches
(5.1 cm) forward of the rear wheel opening.
Make sure the jack head is touching the metal
jacking ange under the body. Do not place the jack
under the plastic body panel.
4. Put the compact spare tire near you.
{CAUTION:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack you
could be badly injured or killed. Never get
under a vehicle when it is supported only by
a jack.
{CAUTION:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to t the
jack lift head into the proper location before
raising the vehicle.
5-83
ProCarManuals.com

5. Raise the vehicle by turning the jack handle
clockwise. Raise the vehicle far enough off the
ground so there is enough room for the compact
spare tire to t under the vehicle.6. Remove all of the
wheel nuts.
5-84
ProCarManuals.com