2006 NISSAN VERSA window

INTELLIGENT KEY SYSTEM
BL-113
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
WORK SUPPORT
Monitor item Description
CONFIRM KEY FOB ID It can be checked whether Intelligent Key ID code is registered or not in this mode.
TAKE OUT FROM WINDOW
WAR NTake away warning chime (from window) mode can be changed to operate (ON) or not operate
(OFF) with this mode. The operation mode will be changed when “CHANGE SETT” on CON-
SULT-II screen is touched.
LOW BAT OF KEY FOB WARNIntelligent Key low battery warning mode can be changed to operate (ON) or not operate (OFF)
with this mode. The operation mode will be changed when “CHANGE SETT” on CONSULT-II
screen is touched.
ANSWER BACK FUNCTIONBuzzer reminder function mode by Intelligent button can be changed to operate (ON) or not oper-
ate (OFF) with this mode. The operation mode will be changed when “CHANGE SETT” on CON-
SULT-II screen is touched.
SELECTIVE UNLOCK FUNC-
TIONSelective unlock function mode can be changed to operate (ON) or not operate (OFF) with this
mode. The operation mode will be changed when “CHANGE SETT” on CONSULT-II screen is
touched.
ANTI KEY LOCK IN FUNCTIONKey reminder function mode can be changed to operate (ON) or not operate (OFF) with this
mode. The operation mode will be changed when “CHANGE SETT” on CONSULT-II screen is
touched.
HORN WITH KEYLESS LOCKHorn reminder function mode by Intelligent Key remote control button can be changed to operate
(ON) or not operate (OFF) with this mode. The operation mode will be changed when “CHANGE
SETT” on CONSULT-II screen is touched.
HAZARD ANSWER BACKHazard reminder function mode can be selected from the following with this mode. The operation
mode will be changed when “CHANGE SETT” on CONSULT-II screen is touched.

LOCK ONLY: Door lock operation only

UNLOCK ONLY: Door unlock operation only

LOCK/UNLOCK: Lock/Unlock operation

OFF: Non-operation
ANSWER BACK WITH I-KEY
LOCKBuzzer reminder function (lock operation) mode by door request switch (driver side, passenger
side and back door side) can be selected from the following with this mode. The operation mode
will be changed when “CHANGE SETT” on CONSULT-II screen is touched.

BUZZER: Sound buzzer

OFF: Non-operation
ANSWER BACK WITH I-KEY
UNLOCKBuzzer reminder function (unlock operation) mode by door request switch can be changed to
operate (ON) or not operate (OFF) with this mode.
AUTO RELOCK TIMERAuto door lock timer mode can select the following with this mode.

0.5 minute

OFF: Non-operation
PANIC ALARM DELAYPanic alarm button's pressing time on Intelligent Key remote control button can be selected from
the following with this mode. The operation mode will be changed when “CHANGE SETT” on
CONSULT-II screen is touched.

0.5 second

1.5 second

OFF: Non-operation
P/W DOWN DELAYUnlock button's pressing time on Intelligent Key remote control button can be selected from the
following with this mode. The operation mode will be changed when “CHANGE SETT” on CON-
SULT-II screen is touched.

3 seconds

5 seconds

OFF: Non-operation
ENGINE START BY I-KEYEngine start function mode can be changed to operate (ON) or not operate (OFF) with this mode.
The operation mode will be changed when “CHANGE SETT” on CONSULT-II screen is touched.
LOCK/UNLOCK BY I-KEYDoor lock/unlock function by door request switch (driver side, passenger side and back door side)
mode can be changed to operate (ON) or not operate (OFF) with this mode. The operation mode
will be changed when “CHANGE SETT” on CONSULT-II screen is touched.

INTELLIGENT KEY SYSTEM
BL-121
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
Take away warning chime (through window)
does not operate.1.Check “TAKE OUT FROM WINDOW WARN” setting in
“WORK SUPPORT”.BL-113
2. Check inside key antenna.BL-143
3. Check key switch.BL-124
4. Check Intelligent Key battery.BL-159
5. Check Intelligent Key warning chime.BL-156
6. Replace Intelligent Key unit.BL-160
Door lock operation warning buzzer does not
operate.1. Check door switch.BL-129
3. Check ignition knob switch.BL-127
4. Check door request switch.BL-132
5. Check back door request switch.BL-134
6. Check outside key antenna (driver side and passenger side).BL-139
7. Check outside key antenna (rear bumper).BL-141
8. Check inside key antenna.BL-143
9. Check Intelligent Key warning buzzer.BL-138
10 Replace Intelligent Key unit.BL-160
Symptom Diagnosis/service procedure Reference page

BL-164
DOOR
Revision: June 20062007 Versa
BACK DOOR
Longitudinal Clearance and Surface Height Adjustment
1. Open and support the back door.
2. Slightly loosen the hinge nuts.
3. Reposition the door as necessary and tighten the nuts.
4. Confirm the adjustment. Repeat as necessary to obtain the desired fit.
1. Back door assembly 2. Back door hinge 3. Tail lamp assembly
4. Back window glass 5. Roof 6. Rear pillar
A. 6.0 ± 1.0 mm (0.24 ± 0.04 in) B. -0.5 ± 1.0 mm (-0.02 ± 0.04 in) C. 5.0 ± 1.2 mm (0.20 ± 0.05 in)
D. 0.0 ± 1.5 mm (0.0 ± 0.06 in) E. 5.0 ± 2.3 mm ( 0.20 ± 0.9 in) F. 2.7 +1.6 -2.1 mm (0.11 + 0.06 - 0.08 in)
G. 5 . 0 ± 1.2 mm ( 0.20 ± 0.05 in) H. 0.0 ± 1.5 mm (0.0 ± 0.06 in)
LIIA2668E

DOOR
BL-167
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
3. Remove the check link bolt.
4. Remove the hinge nuts and the door assembly.
Installation
Installation is in the reverse order of removal.
BACK DOOR
Removal
1. Remove the back door glass. Refer toGW-15, "REAR WINDOW GLASS AND MOLDING" .
2. Remove the back door lock assembly. Refer to BL-175, "
BACK DOOR LOCK" .
3. Remove the back door wire harness.
4. Remove the rear washer nozzle and hose from the back door. Refer to WW-42, "
REAR WASHER NOZ-
ZLE" .
5. Support the back door.
CAUTION:
Two technicians should be used to avoid damaging the back door during removal.
6. Remove the back door stays.
7. Remove the door side nuts and the back door assembly. 14.7 N·m (1.5 kg-m, 11 ft-lb)
PIIB6543E
24.5 N·m (2.5 kg-m, 18 ft-lb)
PIIB6522E
LIIA2639E

FRONT DOOR LOCK
BL-169
C
D
E
F
G
H
J
K
L
MA
B
BL
Revision: June 20062007 Versa
FRONT DOOR LOCKPFP:80502
Component Parts LocationEIS00932
Removal and InstallationEIS00933
REMOVAL
1. Remove front door finisher. Refer to EI-27, "Removal and Installation" .
2. Fully close front door window.
3. Remove the front door sealing screen.
NOTE:
If sealing screen is reused, cut butyl tape in a way that leaves it on the sealing screen.
4. Remove front door rear glass run channel. Refer to GW-43, "
Removal and Installation" .
5. Remove the cables from the holder.
6. Remove inside handle bolt, and slide the handle toward the rear
of the vehicle. disengage the handle from the door panel, and
remove the inside handle.
7. Disengage the handle from the door panel, and remove the inside handle.
1. Front door 2. Inside handle 3. Inside handle cable
4. Door lock assembly 5. Outside handle cable 6. TORX bolt (T30)
7. Key cylinder connecting rod 8. Grommet 9. TORX bolt (T30)
10. Rear gasket 11. Door key cylinder assembly
(Driver's side)
Outside handle escutcheon
(passenger's side)12. Outside handle
13. Front gasket 14. Lock knob cable 15. Holder
16. Outside handle bracket
PIIB6523E
PIIB6524E

BL-172
REAR DOOR LOCK
Revision: June 20062007 Versa
REAR DOOR LOCKPFP:82502
Component Parts LocationEIS00934
Removal and InstallationEIS00935
REMOVAL
1. Remove the partition glass. Refer to GW-47, "REAR DOOR GLASS AND REGULATOR" .
2. Support door glass while lifting it up to the door window completely closed position.
3. Remove inside handle bolt, slide handle toward rear of vehicle,
disconnect it from the door panel, and remove the inside handle.
4. Disconnect the inside handle and lock knob cables from the
inside handle.
CAUTION:
During removal and installation, do not to bend the ends of
the lock knob cable and inside handle cable.
1. Rear door 2. Inside handle 3. Inside handle cable
4. Door lock assembly 5. TORX bolt (T30) 6. Outside handle cable
7. Grommet 8. TORX bolt (T30) 9. Rear gasket
10. Outside handle escutcheon 11. Outside handle 12. Front gasket
13. Lock knob cable 14. Outside handle bracket
PIIB6530E
PIIB6524E
PIIB6525E

BL-176
BACK DOOR LOCK
Revision: June 20062007 Versa
System DescriptionEIS0 09 DL
Power is supplied at all times

through 40A fusible link (letter g, located in fuse and fusible link box)

to BCM terminal 70

through 10A fuse [No. 8, located in fuse block (J/B)]

to BCM terminal 57

through 10A fuse [No. 31, located in fuse block (J/B)]

to Intelligent Key unit terminal 11 (if equipped).
Ground is supplied

to BCM terminal 67 and

to Intelligent Key unit terminal 12 (if equipped)

through body grounds M57 and M61.
When back door opener switch is ON (pushed), ground is supplied

to BCM terminal 30 (without Intelligent Key)

through back door opener switch terminals 1 and 2

through front door lock actuator LH (door unlock sensor) terminals 4 and 5 (without power windows) or

through front door lock actuator RH (door unlock sensor) terminals 4 and 5 (with power windows)

through body grounds M57 and M61

to Intelligent Key unit terminal 24 (if equipped)

through back door opener switch terminals 1 and 2

through body grounds B117, B132 and D402.
Then power is supplied

through BCM terminal 53

to back door lock assembly (actuator) terminal 1.
Ground is supplied

to back door lock assembly (actuator) terminal 2

through body grounds B117, B132 and D402.
Then BCM operates back door lock assembly (actuator).

BL-180
BACK DOOR LOCK
Revision: June 20062007 Versa
CONSULT-II APPLICATION ITEMS
Data Monitor
* : With Intelligent Key system
** : Without Intelligent Key system
Active Test
Work FlowEIS009DP
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to BL-176, "
System Description" .
3. Repair or replace any malfunctioning parts. Refer to BL-180, "
Trouble Diagnosis Chart by Symptom" .
4. Does back door opener operate normally? If Yes, GO TO 5. If No, GO TO 3.
5. INSPECTION END
Trouble Diagnosis Chart by SymptomEIS009DQ
BCM Power Supply and Ground CircuitEIS009DR
Refer to BCS-16, "BCM Power Supply and Ground Circuit Check" .
Monitor item Content
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
KEYLESS TRUNK** This is displayed even when it is not equipped.
I-KEY TRUNK* Momentarily indicates [ON/OFF] condition of back door open signal from back door opener switch.
TRNK OPNR SW** Indicates [ON/OFF] condition of back door open signal from back door opener switch.
VEHICLE SPEED This is displayed even when it is not equipped.
Test item Content
TRUNK/BACK DOORThis test is able to check back door lock assembly (actuator) unlock operation.
Actuator opens back door lock assembly when “OPEN” on CONSULT-II screen is touched.
Symptom Diagnoses/service procedureReference
page
Back door opener does not operate.
(Without Intelligent Key or power windows)1. Check BCM power supply and ground circuit.BCS-16
2. Check back door opener switch circuit.BL-181
3. Check back door lock assembly (actuator) circuit.BL-189
4. Replace BCM.BCS-25
Back door opener does not operate.
(Without Intelligent Key, with power windows)1. Check BCM power supply and ground circuit.BCS-162. Check back door opener switch circuit.BL-184
3. Check back door lock assembly (actuator) circuit.BL-189
4. Replace BCM.BCS-25
Back door opener does not operate.
(With Intelligent Key)1. Check BCM power supply and ground circuit.BCS-16
2.Check Intelligent Key power supply and ground cir-
cuit.BL-123
3. Check back door opener switch circuit.BL-187
4. Check back door lock assembly (actuator) circuit.BL-189
5. Replace BCM.BCS-25