2006 NISSAN VERSA check oil

HEADLAMP (FOR USA)
LT-23
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
3. CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
Select “BCM” on CONSULT-II, and perform self-diagnosis for
“BCM”.
Display of self
-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
CAN COMM CIRCUIT>> Refer to LAN-44, "
TROUBLE DIAGNO-
SIS" .
Aiming AdjustmentEKS00IMG
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level surface.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
1. Turn headlamp low beam ON.
2. Use adjusting screw to perform aiming adjustment.
PKIA7627E
1. Headlamp A. Inner and outer adjustment B. Adjusting screw
WKIA5417E

HEADLAMP (FOR CANADA) - DAYTIME LIGHT SYSTEM -
LT-37
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
6. CHECK DAYTIME LIGHT RELAY 1 CONTROL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect daytime light relay 1 connector E37.
3. Disconnect IPDM E/R connector E43.
4. Check continuity between IPDM E/R connector E43 (A) terminal
6 and daytime light relay 1 connector E37 (B) terminal 1.
OK or NG
OK >> Replace the IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
NG >> Repair harness or connector.
Aiming AdjustmentEKS00IM4
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level surface.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
1. Turn headlamp low beam ON.
2. Use adjusting screw to perform aiming adjustment.
A B Continuity
Connector Terminal Connector Terminal
Ye s
E43 6 E37 1
WKIA5553E
1. Headlamp A. Inner and outer adjustment B. Adjusting screw
WKIA5417E

LU-1
ENGINE LUBRICATION SYSTEM
B ENGINE
CONTENTS
C
D
E
F
G
H
I
J
K
L
M
SECTION LU
A
LU
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 2
Precautions for Liquid Gasket .................................. 2
LIQUID GASKET APPLICATION PROCEDURE ..... 2
PREPARATION ........................................................... 3
Special Service Tools ............................................... 3
Commercial Service Tools ........................................ 3
LUBRICATION SYSTEM ............................................ 4
Lubrication Circuit .................................................... 4
ENGINE OIL ............................................................... 5
Inspection ................................................................. 5
ENGINE OIL LEVEL ............................................. 5
ENGINE OIL APPEARANCE ................................ 5ENGINE OIL LEAKAGE ........................................ 5
OIL PRESSURE CHECK ...................................... 5
Changing Engine Oil ................................................. 6
OIL FILTER ................................................................. 8
Removal and Installation .......................................... 8
REMOVAL ............................................................. 8
INSTALLATION ..................................................... 8
INSPECTION AFTER INSTALLATION .................. 8
SERVICE DATA AND SPECIFICATIONS (SDS) ........ 9
Standard and Limit .................................................... 9
OIL PRESSURE .................................................... 9
OIL CAPACITY ...................................................... 9

ENGINE OIL
LU-5
C
D
E
F
G
H
I
J
K
L
MA
LU
Revision: June 20062007 Versa
ENGINE OILPFP:KLA92
InspectionEBS00T71
ENGINE OIL LEVEL
NOTE:
Before starting engine, park vehicle on a level surface and check the engine oil level. If engine is already
started, stop it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range (A) as shown.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE

Check engine oil for white turbidity or heavy contamination.

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:

Oil pan (upper and lower)

Oil pan drain plug

Oil pressure switch

Oil filter

Intake valve timing control solenoid valve

Front cover

Mating surface between cylinder block and cylinder head

Mating surface between cylinder head and rocker cover

Crankshaft oil seals (front and rear)

Oil filter (for intake valve timing control)
OIL PRESSURE CHECK
WA RN ING:

Be careful not to burn yourself, as engine oil may be hot.

For engine oil pressure check the transaxle should be in “ Park position” (A/T models) and (CVT
models) or “Neutral position” (M/T models), and apply the parking brake securely.
1. Disconnect harness connector at oil pressure switch (1), and
remove oil pressure switch using a suitable tool.

Oil pan (lower) (2)

⇐ Front
WBIA0776E
PBIC3310E

LU-6Revision: June 2006
ENGINE OIL
2007 Versa
2. Install oil pressure gauge and hose.
3. Check engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL" .
4. Start engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
Engine oil pressure [Engine oil temperature at 80°C (176°F)]
If difference is extreme, check oil passage and oil pump for oil leaks.
6. After the inspections, install oil pressure switch as follows:
a. Remove old liquid gasket adhering to oil pressure switch and engine.
b. Apply liquid gasket and tighten oil pressure switch to specification.
Use Genuine Silicone RTV Sealant or equivalent. Refer to GI-46, "
RECOMMENDED CHEMICAL
PRODUCTS AND SEALANTS" .
c. Check engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL" .
d. After warming up engine, make sure there are no engine leaks of oil with running engine.
Changing Engine OilEBS00T72
WAR NIN G:

Be careful not to burn yourself, as engine oil may be hot.

Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct
skin contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand
cleaner as soon as possible.
1. Warm up engine, park vehicle on a level surface and check for engine oil leakage from engine compo-
nents. Refer to LU-5, "
ENGINE OIL LEAKAGE" .
2. Stop engine and wait for 10 minutes.Tool number : ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Engine speed
rpm Approximate discharge pressure
kPa (bar, kg/cm2 , psi)
Idle speed More than 60 (0.60, 0.61, 9)
2,000 More than 200 (2.0, 2.0, 29)
Oil pressure switch : 14.7 N·m (1.5 kg-m, 11 ft-lb)

ENGINE OIL
LU-7
C
D
E
F
G
H
I
J
K
L
MA
LU
Revision: June 20062007 Versa
3. Loosen oil filler cap (1) and then remove drain plug (2).

Oil filter (3)

⇐ Engine front
4. Drain engine oil.
5. Install drain plug (2) with new washer. Refer to EM-24, "
Compo-
nents" .
CAUTION:
Be sure to clean drain plug (2) and install with new washer.
6. Refill with new engine oil.
Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRI-
CANTS" .
CAUTION:

The refill capacity depends on the engine oil temperature
and drain time. Use these specifications for reference
only.

Always use oil level gauge to determine the proper
amount of engine oil in the engine.
7. Warm up engine and check area around drain plug (2) and oil fil-
ter (3) for engine oil leakage.
8. Stop engine and wait for 10 minutes.
9. Check the engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL"
.
PBIC3915E

LU-8Revision: June 2006
OIL FILTER
2007 Versa
OIL FILTERPFP:15208
Removal and InstallationEBS00T73
REMOVAL
1. Remove oil filter using Tool (A).

⇐ Front
CAUTION:

Oil filter is provided with relief valve. Use Genuine NIS-
SAN Oil Filter or equivalent.

Be careful not to get burned when engine and engine oil
may be hot.

When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.

Do not allow engine oil to adhere to drive belt.

Completely wipe off any engine oil that adheres to engine and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to LU-5, "ENGINE OIL" .
2. Start engine, and make sure there is no leaks of engine oil.
3. Stop engine and wait for 10 minutes.
4. Check the engine oil level and adjust engine oil. Refer to LU-5, "
ENGINE OIL" . Tool number : KV10115801 (J-38956)
PBIC3818E
SM A01 0
Oil filter: : 17.7 N·m (1.8 kg-m, 13 ft-lb)
SM A22 9B

MA-1
MAINTENANCE
L MAINTENANCE
CONTENTS
C
D
E
F
G
H
I
J
K
M
SECTION MA
A
B
MA
Revision: June 20062007 Versa PRECAUTIONS .......................................................... 3
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .................................................................. 3
PREPARATION ........................................................... 4
Special Service Tools ............................................... 4
Commercial Service Tools ........................................ 4
GENERAL MAINTENANCE ....................................... 5
Explanation of General Maintenance ....................... 5
General Maintenance ............................................... 5
PERIODIC MAINTENANCE ....................................... 7
Introduction of Periodic Maintenance ....................... 7
Schedule 1 ............................................................... 7
EMISSION CONTROL SYSTEM MAINTE-
NANCE .................................................................. 7
CHASSIS AND BODY MAINTENANCE ............... 8
Schedule 2 ............................................................... 9
EMISSION CONTROL SYSTEM MAINTE-
NANCE .................................................................. 9
CHASSIS AND BODY MAINTENANCE ............. 10
RECOMMENDED FLUIDS AND LUBRICANTS .......11
Fluids and Lubricants ..............................................11
SAE Viscosity Number ........................................... 12
Anti-freeze Coolant Mixture Ratio .......................... 12
ENGINE MAINTENANCE ......................................... 13
Drive Belts .............................................................. 13
Checking Drive Belts .............................................. 13
Tension Adjustment ................................................ 13
Changing Engine Coolant ...................................... 13
DRAINING ENGINE COOLANT ......................... 13
REFILLING ENGINE COOLANT ........................ 14
FLUSHING COOLING SYSTEM ......................... 15
Inspection ............................................................... 15
LEVEL CHECK ................................................... 15
CHECKING COOLING SYSTEM FOR LEAKS ... 15
Checking Fuel Lines ............................................... 15
Changing Air Cleaner Filter .................................... 16
REMOVAL ........................................................... 16
INSPECTION AFTER REMOVAL ....................... 16
INSTALLATION ................................................... 16Changing Engine Oil ............................................... 16
Engine Oil Filter ...................................................... 17
REMOVAL ........................................................... 17
INSTALLATION ................................................... 17
INSPECTION AFTER INSTALLATION ................ 18
Changing Spark Plugs ............................................ 18
............................................................................ 18
INSPECTION AFTER REMOVAL ....................... 18
INSTALLATION ................................................... 19
Checking EVAP Vapor Lines .................................. 19
CHASSIS AND BODY MAINTENANCE ................... 20
Changing In-cabin Microfilter .................................. 20
Checking Exhaust System ...................................... 20
Checking CVT Fluid ................................................ 20
FLUID LEVEL CHECK ........................................ 20
FLUID CONDITION CHECK ............................... 21
Changing CVT Fluid ............................................... 21
Checking Clutch Fluid Level and Leaks ................. 22
Checking Clutch System ........................................ 22
Checking M/T Oil .................................................... 22
OIL LEAKAGE AND OIL LEVEL ......................... 22
Changing M/T Oil .................................................... 22
DRAINING ........................................................... 22
FILLING ............................................................... 22
Checking A/T Fluid ................................................. 22
Changing A/T Fluid ................................................. 23
Balancing Wheels ................................................... 24
Rotation .................................................................. 24
Checking Brake Fluid Level and Leaks .................. 24
Checking Brake Lines and Cables ......................... 24
Changing Brake Fluid ............................................. 25
Checking Disc Brake .............................................. 25
ROTOR ................................................................ 25
CALIPER ............................................................. 25
PAD ..................................................................... 25
WHEEL CYLINDER ............................................ 26
LINING ................................................................ 26
Axle and Suspension Parts .................................... 26
Drive Shaft .............................................................. 27