2006 NISSAN VERSA stop start

EM-62Revision: June 2006
CYLINDER HEAD
2007 Versa
CYLINDER HEADPFP:11041
On-Vehicle ServiceEBS00T6K
CHECKING COMPRESSION PRESSURE
1. Warm up engine thoroughly. Then, stop it.
2. Release fuel pressure. Refer to EC-81, "
FUEL PRESSURE RELEASE" .
3. Disconnect fuel pump fuse (1) to avoid fuel injection during mea-
surement.
4. Remove engine cover. Refer to EM-18, "
Components" .
5. Remove ignition coil and spark plug from each cylinder. Refer to EM-30, "
IGNITION COIL, SPARK PLUG
AND ROCKER COVER" .
6. Connect an engine tachometer (not required in use of CONSULT-II).
7. Install a suitable compression tester with an adapter onto spark
plug hole.

Use the adapter whose picking up end inserted to spark plug
hole is smaller than 20 mm (0.79 in) in diameter. Otherwise, it
may be caught by cylinder head during removal.
8. With accelerator pedal fully depressed, turn ignition switch to “START” for cranking. When the gauge
pointer stabilizes, read the compression pressure and the engine rpm. Perform these steps to check each
cylinder.
Compression pressure:
Unit: kPa (bar, kg/cm2 psi) /rpm
CAUTION:
Always use fully a changed battery to obtain the specified engine speed.
: Vehicle front
PBIA9861J
LBIA0459E
SBIA0533E
Standard Minimum Differential limit between cylinders
1,500 (15.0, 15.3, 217.6) / 200 1,200 (12.0, 12.2, 174) / 200 100 (1, 1, 15) / 200

EM-76Revision: June 2006
ENGINE ASSEMBLY
2007 Versa
INSTALLATION
Note the following, and install in the reverse order of removal.

Do not allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting
insulator.

When installation directions are specified, install parts according to the directions. Refer to EM-73, "Com-
ponents" .

Make sure that each mounting insulator is seated properly, and tighten nuts and bolts.

Tighten engine mounting insulator (RH) bolts in the numerical
order shown.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.

Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRICANTS" .

Use procedure below to check for fuel leakage.
–Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–Start engine. With engine speed increased, check again for fuel leakage at connection points.

Run engine to check for unusual noise and vibration.

Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.

Bleed air from lines and hoses of applicable lines, such as in cooling system.

After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.: Vehicle front
WBIA0785E
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —

SQUEAK AND RATTLE TROUBLE DIAGNOSES
GW-7
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: June 20062007 Versa
80845-71L00: 30 mm (1.18 in) thick, 30×50 mm (1.18×1.97 in)
FELT CLOTH TAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15×25 mm (0.59×0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll. The following
materials not found in the kit can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used instead of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingEIS009E0
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicone spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops
Tapping or moving the components or pressing on them while driving to duplicate the conditions can isolate
many of these incidents. You can usually insulate the areas with felt cloth tape or insulator foam blocks from
the NISSAN Squeak and Rattle Kit (J-43980) to repair the noise.

IDX-6
ALPHABETICAL INDEX
R
Radiator ............................................................ CO-11
Rear axle .......................................................... RAX-4
Rear combination lamp removal and installation LT-87
Rear door .......................................................... GW-47
Rear seat belt ...................................................... SB-6
Rear suspension ............................................... RSU-5
Rear washer .................................................... WW-30
Rear window defogger ...................................... GW-50
Rear wiper ....................................................... WW-30
Refrigerant connection precaution .................... MTC-5
Refrigerant discharging evacuating charging . MTC-80
Refrigerant general precaution ......................... MTC-5
Refrigerant lines .............................................. MTC-80
Refrigerant pressure sensor ............. EC-586, MTC-88
Refrigeration cycle .......................................... MTC-16
Remote keyless entry system ............................ BL-54
Removal and installation (A/T) ......................... AT-253
Reverse idler shaft (M/T) ................................... MT-18
Reverse lamp switch (M/T) - See Back-up lamp switch
(M/T) .................................................................. MT-11
Reverse main gear (M/T) ................................... MT-18
Road test ......... AT-58, AT-61, AT-64, AT-65, CVT-46
Room lamp - See Interior lamp ........................... LT-91
RP/SEN - Wiring diagram ................................ EC-587
S
SAE J1979 - Service $01 - 09 ........................... EC-47
Seat belt inspection ................................ SB-8, MA-27
Seat belt, front ..................................................... SB-3
Seat belt, rear ...................................................... SB-6
Secondary pressure sensor ........................... CVT-129
Secondary Speed Sensor ................................ CVT-95
SECPS - Wiring diagram ............................... CVT-130
SECPSV - Wiring diagram ............................. CVT-125
Self-diagnostic results .......................... EC-64, EC-116
SEN/PW - Wiring diagram ............................... EC-431
SESCVT - Wiring diagram ............................... CVT-96
SHIFT - Wiring diagram ................... AT-236, CVT-198
Shift control ...................................................... CVT-26
Shift control components (M/T) .......................... MT-21
Shift control system ....................................... CVT-191
Shift fork (M/T) ................................................... MT-21
Shift lever ........................................................... MT-12
Shift lock system .............................................. AT-235
Shift schedule ..................... AT-67, CVT-53, CVT-210
Shock absorber (rear) ....................................... RSU-9
Side air bag (satellite) sensor ......................... SRS-50
Side curtain air bag ......................................... SRS-47
Side trim .............................................................. EI-32
SMJ (super multiple junction) ............................ PG-75
Specification value ........................................... EC-133
Speedometer ........................................................ DI-5
Spiral cable ..................................................... SRS-44
Spot lamp .......................................................... LT-107
SPSW - Wiring diagram ................................. CVT-171
SROOF - Wiring diagram ................................... RF-13
SRS - See Supplemental Restraint System ...... SRS-4
SRS - Wiring diagram ..................................... SRS-13
SRS Trouble diagnoses .................................... SRS-9
SSV/A - Wiring diagram ................................... AT-152
SSV/B - Wiring diagram ................................... AT-157
Stall Test ......................................................... CVT-43
Stall test (A/T) .................................................... AT-53
START - Wiring diagram ................................... SC-12
Starting system ................................................. SC-10
Steering linkage ................................................. PS-12
Steering wheel and column ........................ PS-6, PS-9
Steering wheel turning force ................................ PS-6
Step motor .................................... CVT-164, CVT-168
STM - Wiring diagram ................................... CVT-165
Stop lamp ................................................ LT-71, LT-87
Stop lamp switch ............................................. EC-488
STOP/L - Wiring diagram ................................... LT-71
STSIG - Wiring diagram .................................. CVT-73
Sun roof, electric ................................................ RF-10
Sunroof .................................................. RF-10, RF-22
Supplemental Restraint System ........................ SRS-4
Suspension ....................................................... MA-26
Swirl control valve ........................................... EC-592
Symbols and abbreviations ...................... GI-10, GI-23
Symptom matrix chart ....................................... EC-92
Synchronizer (M/T) ........................................... MT-18
System readiness test (SRT) code ................... EC-52
T
Tachometer ........................................................... DI-5
Tail lamp ............................................................ LT-87
TAIL/L - Wiring diagram ..................................... LT-78
TCM circuit diagram ........................................ CVT-42
TCM function ................................................... CVT-24
TCM inspection table ........................... AT-78, CVT-54
TCV - Wiring diagram ...................... AT-135, CVT-106
Telephone .......................................................... AV-49
Theft warning system - See Vehicle security (Theft warn-
ing) system ....................................................... BL-193
Thermo control amp ........................................ MTC-63
Thermostat ........................................................ CO-18
Three way catalyst function ............................ EC-334
Three way catalyst precautions ............................ GI-5
Throttle control motor relay ............................. EC-493
Throttle position sensor (TPS) .. EC-206, EC-302, EC-
460, EC-462, EC-526
Throttle valve closed position learning .............. EC-78
Tie-rod ................................................................ PS-12
Timing chain ...................................................... EM-37
TLID - Wiring diagram ...................................... BL-177
Torque converter installation .... AT-254, AT-369, CVT-
208
Torque convertor clutch solenoid valve CVT-105, CVT-
110
TPS1 - Wiring diagram .................................... EC-304
TPS2 - Wiring diagram .................................... EC-208
TPS3 - Wiring diagram .................................... EC-528
Transmission case (M/T) .................................. MT-17

IP-6
SQUEAK AND RATTLE TROUBLE DIAGNOSES
Revision: June 20062007 Versa
73982-9E000: 45 mm (1.77 in) thick, 50 x 50 mm (1.97 x 1.97 in)/73982-50Y00: 10 mm (0.39 in) thick, 50 x 50
mm (1.97 x 1.97 in)
INSULATOR (Light foam block)
80845-71L00: 30 mm (1.18 in) thick, 30 x 50 mm (1.18 x 1.97 in)
FELT CLOTH TAPE
Used to insulate where movement does not occur. Ideal for instrument panel applications.
68370-4B000: 15 x 25 mm (0.59 x 0.98 in) pad/68239-13E00: 5 mm (0.20 in) wide tape roll
The following materials, not found in the kit, can also be used to repair squeaks and rattles.
UHMW (TEFLON) TAPE
Insulates where slight movement is present. Ideal for instrument panel applications.
SILICONE GREASE
Used in place of UHMW tape that will be visible or not fit.
Note: Will only last a few months.
SILICONE SPRAY
Use when grease cannot be applied.
DUCT TAPE
Use to eliminate movement.
CONFIRM THE REPAIR
Confirm that the cause of a noise is repaired by test driving the vehicle. Operate the vehicle under the same
conditions as when the noise originally occurred. Refer to the notes on the Diagnostic Worksheet.
Generic Squeak and Rattle TroubleshootingEIS009AW
Refer to Table of Contents for specific component removal and installation information.
INSTRUMENT PANEL
Most incidents are caused by contact and movement between:
1. The cluster lid A and instrument panel
2. Acrylic lens and combination meter housing
3. Instrument panel to front pillar garnish
4. Instrument panel to windshield
5. Instrument panel mounting pins
6. Wiring harnesses behind the combination meter
7. A/C defroster duct and duct joint
These incidents can usually be located by tapping or moving the components to duplicate the noise or by
pressing on the components while driving to stop the noise. Most of these incidents can be repaired by apply-
ing felt cloth tape or silicone spray (in hard to reach areas). Urethane pads can be used to insulate wiring har-
ness.
CAUTION:
Do not use silicone spray to isolate a squeak or rattle. If you saturate the area with silicone, you will
not be able to recheck the repair.
CENTER CONSOLE
Components to pay attention to include:
1. Shifter assembly cover to finisher
2. A/C control unit and cluster lid C
3. Wiring harnesses behind audio and A/C control unit
The instrument panel repair and isolation procedures also apply to the center console.
DOORS
Pay attention to the:
1. Finisher and inner panel making a slapping noise
2. Inside handle escutcheon to door finisher
3. Wiring harnesses tapping
4. Door striker out of alignment causing a popping noise on starts and stops

ENGINE OIL
LU-5
C
D
E
F
G
H
I
J
K
L
MA
LU
Revision: June 20062007 Versa
ENGINE OILPFP:KLA92
InspectionEBS00T71
ENGINE OIL LEVEL
NOTE:
Before starting engine, park vehicle on a level surface and check the engine oil level. If engine is already
started, stop it and allow 10 minutes before checking.
1. Pull out oil level gauge and wipe it clean.
2. Insert oil level gauge and make sure the engine oil level is within
the range (A) as shown.
3. If it is out of range, adjust it.
ENGINE OIL APPEARANCE

Check engine oil for white turbidity or heavy contamination.

If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:

Oil pan (upper and lower)

Oil pan drain plug

Oil pressure switch

Oil filter

Intake valve timing control solenoid valve

Front cover

Mating surface between cylinder block and cylinder head

Mating surface between cylinder head and rocker cover

Crankshaft oil seals (front and rear)

Oil filter (for intake valve timing control)
OIL PRESSURE CHECK
WA RN ING:

Be careful not to burn yourself, as engine oil may be hot.

For engine oil pressure check the transaxle should be in “ Park position” (A/T models) and (CVT
models) or “Neutral position” (M/T models), and apply the parking brake securely.
1. Disconnect harness connector at oil pressure switch (1), and
remove oil pressure switch using a suitable tool.

Oil pan (lower) (2)

⇐ Front
WBIA0776E
PBIC3310E

LU-6Revision: June 2006
ENGINE OIL
2007 Versa
2. Install oil pressure gauge and hose.
3. Check engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL" .
4. Start engine and warm it up to normal operating temperature.
5. Check oil pressure with engine running under no-load.
NOTE:
When engine oil temperature is low, engine oil pressure becomes high.
Engine oil pressure [Engine oil temperature at 80°C (176°F)]
If difference is extreme, check oil passage and oil pump for oil leaks.
6. After the inspections, install oil pressure switch as follows:
a. Remove old liquid gasket adhering to oil pressure switch and engine.
b. Apply liquid gasket and tighten oil pressure switch to specification.
Use Genuine Silicone RTV Sealant or equivalent. Refer to GI-46, "
RECOMMENDED CHEMICAL
PRODUCTS AND SEALANTS" .
c. Check engine oil level. Refer to LU-5, "
ENGINE OIL LEVEL" .
d. After warming up engine, make sure there are no engine leaks of oil with running engine.
Changing Engine OilEBS00T72
WAR NIN G:

Be careful not to burn yourself, as engine oil may be hot.

Prolonged and repeated contact with used engine oil may cause skin cancer; try to avoid direct
skin contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand
cleaner as soon as possible.
1. Warm up engine, park vehicle on a level surface and check for engine oil leakage from engine compo-
nents. Refer to LU-5, "
ENGINE OIL LEAKAGE" .
2. Stop engine and wait for 10 minutes.Tool number : ST25051001 (J-25695-1)
: ST25052000 (J-25695-2)
WBIA0571E
Engine speed
rpm Approximate discharge pressure
kPa (bar, kg/cm2 , psi)
Idle speed More than 60 (0.60, 0.61, 9)
2,000 More than 200 (2.0, 2.0, 29)
Oil pressure switch : 14.7 N·m (1.5 kg-m, 11 ft-lb)

LU-8Revision: June 2006
OIL FILTER
2007 Versa
OIL FILTERPFP:15208
Removal and InstallationEBS00T73
REMOVAL
1. Remove oil filter using Tool (A).

⇐ Front
CAUTION:

Oil filter is provided with relief valve. Use Genuine NIS-
SAN Oil Filter or equivalent.

Be careful not to get burned when engine and engine oil
may be hot.

When removing, prepare a shop cloth to absorb any
engine oil leakage or spillage.

Do not allow engine oil to adhere to drive belt.

Completely wipe off any engine oil that adheres to engine and vehicle.
INSTALLATION
1. Remove foreign materials adhering to the oil filter installation surface.
2. Apply new engine oil to the oil seal contact surface of new oil fil-
ter.
3. Screw oil filter manually until it touches the installation surface,
then tighten it by 2/3 turn. Or tighten to specification.
INSPECTION AFTER INSTALLATION
1. Check the engine oil level. Refer to LU-5, "ENGINE OIL" .
2. Start engine, and make sure there is no leaks of engine oil.
3. Stop engine and wait for 10 minutes.
4. Check the engine oil level and adjust engine oil. Refer to LU-5, "
ENGINE OIL" . Tool number : KV10115801 (J-38956)
PBIC3818E
SM A01 0
Oil filter: : 17.7 N·m (1.8 kg-m, 13 ft-lb)
SM A22 9B