2006 NISSAN MURANO radio

a station transmitter, the signals will tend to fade
and/or drift.
Static and flutter: During signal interference from
buildings, large hills or due to antenna position,
usually in conjunction with increased distance
from the station transmitter, static or flutter can
be heard. This can be reduced by adjusting the
treble control counterclockwise to reduce treble
response.
Multipath reception: Because of the reflective
characteristics of FM signals, direct and re-
flected signals reach the receiver at the same
time. The signals may cancel each other, result-
ing in momentary flutter or loss of sound.AM RADIO RECEPTIONAM signals, because of their low frequency, can
bend around objects and skip along the ground.
In addition, the signals can be bounced off the
ionosphere and bent back to earth. Because of
these characteristics, AM signals are also sub-
ject to interference as they travel from transmitter
to receiver.
Fading: Occurs while the vehicle is passing
through freeway underpasses or in areas with
many tall buildings. It can also occur for several
seconds during ionospheric turbulence even in
areas where no obstacles exist.
Static: Caused by thunderstorms, electricalpower lines, electric signs and even traffic lights.
SATELLITE RADIO RECEPTIONWhen the satellite radio is first installed or the
battery has been replaced, the satellite radio
may not work properly. This is not a malfunction.
Wait more than 10 minutes with satellite radio
ON for satellite radio to receive all of the neces-
sary data.
The satellite radio mode will be skipped or “NO
SAT” will be displayed unless the optional sat-
ellite receiver and antenna are installed, and an
XM
or SIRIUS
TM
satellite radio service sub-
scription is active.
Satellite radio performance may be effected if
cargo carried on the roof rack blocks the satellite
radio signal.
If possible, do not put cargo over the satellite
radio antenna.
AUDIO OPERATION PRECAUTIONS
Cassette player
To maintain good quality sound,
NISSAN recommends using cassette
tapes of 60 minutes or shorter in length.

Cassette tapes should be removed from
the player when not in use. Store cas-
settes in their protective cases andaway from direct sunlight, heat, dust,
moisture and magnetic sources.

Direct sunlight can cause the cassette to
become deformed. The use of deformed
cassettes may cause the cassette to jam
in the player.

Do not use cassettes with labels which
are peeling and loose. If used, the label
could jam in the player.

If a cassette has loose tape, insert a
pencil through one of the cassette hubs
and rewind the tape firmly around the
hubs. Loose tape may cause tape jam-
ming and wavering sound quality.

Over a period of time, the playback
head, capstan and pinch roller may col-
lect a tape coating residue as the tape is
played. This residue accumulation can
cause weak or wavering sound, and
should be removed periodically with a
head cleaning tape. If the residue is not
removed periodically, the player may
need to be disassembled for cleaning.
4-28
Display screen, heater, air conditioner and audio systems


05.8.26/Z50-D/V5.0


1. SEEK/TRACK button
2. CD slot
3. Station and preset (FM/AM/SAT)
4. SCAN button
5. CD EJECT button
6. CAT button
7. POWER button/VOLUME control knob
8. DISP (display) button
9. PRESET A⋅B⋅C button
10. CD button11. RADIO button
12. PAUSE/MUTE button
13. TUNE up/down, TRACK up/down and AU-
DIO button
14. RPT (repeat)/RDM (random) button
FM-AM-SAT RADIO WITH CD
PLAYERNo satellite radio reception is available when the
SAT band option is selected unless optional
satellite receiver and antenna are installed, and
an XM
®
or SIRIUS
TM
satellite radio service
subscription is active.
It may take some time to receive the activation
signal after subscribing to the XM
or SIRIUS
TM
satellite radio provider. After receiving the acti-
vation signal, an available channel list will be
automatically updated in the radio. For XM
, turn
the ignition switch from the LOCK to ACC
position to update the channel list.
Satellite radio is not available in Alaska and
Hawaii.
Audio main operationPOWER/Volume control:
Turn the ignition switch to ACC or ON, and then
push the POWER button while the system is off
to call up the mode (radio or CD) which was
playing immediately before the system was
turned off. When no CD is loaded, the radio will
come on. While the system is on, pushing the
POWER button turns the system off.
To turn the radio off, push the POWER button.
SAA1360
Display screen, heater, air conditioner and audio systems
4-33


05.8.26/Z50-D/V5.0


Turn the Volume control knobto adjust the
volume.
AUDIO button/knob:
Push the AUDIO button to change the selecting
mode as follows.
BASS→TREBLE→FADE→BALANCE→
BASS
To adjust Bass, Treble, Fader and Balance, push
the AUDIO button until the desired mode BASS,
TREBLE, FADE or BALANCE appears in the
display. Turn the AUDIO knobto adjust Bass
and Treble to the desired level. Use the Tuning
knobalso to adjust Fader or Balance modes.
Fader adjusts the sound level between the front
and rear speakers and Balance adjusts the
sound between the right and left speakers.
After 10 seconds, the radio or CD display
reappears. Once the sound quality is set to the
desired level, push the AUDIO button repeatedly
until the radio or CD display appears.
Display text:
To indicate the text, push the AUDIO knob
during CD or satellite radio playing.
BASS→TREBLE→FADE→BALANCE→
Display mode
To change the indicated text in display mode,turn the tuning knobwithin 2 seconds.
Display select:
Display CD text
To indicate the CD text, push the
button
while the CD is playing.
The text will change as follows:
Display FM text
To indicate the FM PS name, push the
button while the FM radio is playing.
The name will change as follows:
ON→OFF→ON
When no data is available, “NO TEXT” will
appear.
Display satellite radio text
To indicate the satellite radio text, push thebutton while the satellite radio is playing.
The text will change as follows:
When no data is available, “----” will appear.FM-AM-SAT radio operation
FM/AM/SAT radio select:
The satellite radio mode will be skipped unless
the optional satellite receiver and antenna are
installed, and an XM
or SIRIUS
TM
satellite radio
service subscription is active.
Pushing the RADIO button will change the band
as follows:
AM→FM→SAT (Satellite)
When the RADIO button is pushed while the
ignition switch is in the ACC or ON, the radio will
come on at the station last played.
The last station played will also come on when
the power knobis turned to ON.
If a compact disc is playing when the RADIO
button is pushed, the compact disc will auto-
matically be turned off and the last radio station
played will come on.
The FM stereo indicator ST will glow during FM
stereo reception. When the stereo broadcast
signal is weak, the radio will automatically
change from stereo to monaural reception.
4-34
Display screen, heater, air conditioner and audio systems


05.8.26/Z50-D/V5.0


TUNE (Tuning):
WARNING
The radio should not be tuned while
driving so full attention may be given to
vehicle operation.
To tune the radio, turn the TUNE knobto the
right or left.
Use these buttons for manual tuning.
SEEK tuning:
Push the SEEK button
or
for less
than 0.5 second to tune from high to low or low
to high frequencies and stop at the next broad-
casting station (channel).
Push the SEEK button
or
for more
than 0.5 second, to fast tune from high to low or
low to high frequencies.
SCANtuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broadcast-
ing station (channel) for 5 seconds. Pushing the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station (channel).If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next station
(channel).
Station memory operations:
Eighteen (18) stations can be set for the FM, AM
and SAT band to the A, B and C preset button.
1. Choose preset channel A, B or C using the
preset select button.
2. Tune to the desired station using the SEEK,
SCAN or TUNE button and keep pushing any
of the desired station memory buttons (1 to
6) until a beep sound is heard. (The radio
mutes when the select button is pushed.)
3. The channel indicator will then come on and
the sound will resume. Memorizing is now
complete.
4. Other buttons can be set in the same manner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be erased. In that
case, reset the desired stations.
Radio data system (RDS):
RDS stands for Radio Data System, and is a
data information service transmitted by some
radio stations on the FM band (not AM band)
and/or SATELLITE band encoded within a regu-
lar radio broadcast. Currently, most RDS sta-tions are in large cities, but many stations are
now considering broadcasting RDS data.
RDS can display:

Station call sign, such as “WHFR 98.3”.

Station name, such as “The Groove”.

Music or programming type such as “Classi-
cal”, “Country”, or “Rock”.

Traffic reports about delays or construction.
If the station broadcasts RDS information, the
RDS icon is displayed.
Category (CAT) button:
When the CAT button is pushed for less than
0.5 second, the AM/FM (Satellite) radio frequen-
cies (Category) will move to the next/previous
step (Category). Push and hold the button for
more than 0.5 second to move quickly through
the steps (Categories).
Compact disc (CD) player operationTurn the ignition switch to the ACC or ON
position and insert the compact disc into the slot
with the label side facing up. The compact disc
will be guided automatically into the slot and
start playing.
After loading the disc, the number of tracks on
Display screen, heater, air conditioner and audio systems
4-35


05.8.26/Z50-D/V5.0


the disc and the play time will appear on the
display.
If the radio is already operating, it will automati-
cally turn off and the compact disc will play.
CAUTION
Do not force the compact disc into the
slot. This could damage the player.
If the system has been turned off while the
compact disc was playing, pushing the
POWER/VOL control knobwill start the com-
pact disc.
3.1 inches (8 cm) diameter discs can be used
without an adapter.
PLAY:
When the CD button is pushed with the system
off and the compact disc loaded, the system will
turn on and the compact disc will start to play.
When the CD button is pushed with the com-
pact disc loaded with the radio playing, the tape
or radio will automatically be turned off and the
compact disc will start to play.
FF (Fast Forward), REW
(Rewind), APS (Automatic
Program Search) FF, APS REW:
When the
(fast forward) or
(rewind)
button is pushed and hold while the compact
disc is being played, the compact disc will play
while fast forwarding or rewinding. When the
button is released, the compact disc will return
to normal play speed.
When the
button is pushed for less than
0.5 second while the compact disc is being
played, the program next to the present one will
start to play from its beginning. Push several
times to skip through programs. The compact
disc will advance the number of times the button
is pushed. (When the last program on the
compact disc is skipped through, the first pro-
gram will be played.) When the
button is
pushed for less than 0.5 second, the program
being played returns to its beginning. Push
several times to skip back through programs.
The compact disc will go back the number of
times the button is pushed.
SCAN:
When the SCAN button is pushed while the CD
is playing, each track will play for about 10
seconds.To stop scanning, push the SCAN button
again.
RPT (Repeat)/RDM (Random):
When the RPT/RDM button is pushed while the
compact disc is played, the play pattern can be
changed as follows:CD EJECT:
When the CD EJECT button is pushed with the
compact disc loaded, the compact disc will be
ejected.
When this button is pushed while the compact
disc is being played, the compact disc will come
out and the system will turn off.
If the compact disc comes out and is not
removed, it will be pulled back into the slot
to protect it.
4-36
Display screen, heater, air conditioner and audio systems


05.8.26/Z50-D/V5.0


1. CD LOAD button
2. SEEK/TRACK button
3. CD slot
4. Station and preset (FM/AM/SAT)/CD
insert/eject or CD play select button
5. SCAN button
6. CD EJECT button
7. CAT/FOLDER button
8. POWER button/VOLUME control knob
9. DISP (display) button
10. PRESET A⋅B⋅C button11. CD button
12. RADIO button
13. TAPE EJECT button
14. TAPE button
15. TUNE up/down, TRACK up/down and AU-
DIO button
16. RPT (repeat)/RDM (random) button
FM-AM-SAT RADIO WITH
CASSETTE PLAYER AND CD
CHANGERNo satellite radio reception is available when the
SAT band option is selected unless optional
satellite receiver and antenna are installed, and
an XM
®
or SIRIUS
TM
satellite radio service
subscription is active.
It may take some time to receive the activation
signal after subscribing to the XM
or SIRIUS
TM
satellite radio provider. After receiving the acti-
vation signal, an available channel list will be
automatically updated in the radio. For XM
, turn
the ignition switch from the LOCK to ACC
position to update the channel list.
Satellite radio is not available in Alaska and
Hawaii.
Audio main operationThe tape deck employs a permalloy head which
allows for improved reproduction of high fre-
quency ranges. Noise is also greatly reduced by
the combined use of the Dolby NR (Noise
Reduction) system. The auto loudness circuit
enhances the low frequency range automatically
in both radio reception and tape and CD play-
back.
SAA1315
Display screen, heater, air conditioner and audio systems
4-37


05.8.26/Z50-D/V5.0


POWER/Volume control:
Turn the ignition switch to ACC or ON, and then
push the POWER button while the system is off
to call up the mode (radio, tape or CD) which
was playing immediately before the system was
turned off. When no CD or tape is loaded, the
radio will come on. While the system is on,
pushing the POWER button turns the system
off.
To turn the radio off, push the POWER button.
Turn the Volume control knobto adjust the
volume.
This vehicle hasSpeed Sensitive control Vol-
ume (SSV) for audio. The audio volume
changes as the driving speed changes.
AUDIO button/knob:
Push the AUDIO button to change the selecting
mode as follows.
BASS→TREBLE→FADE→BALANCE→
SSV→NR (when cassette playing)
To adjust Bass, Treble, Fader and Balance, push
the AUDIO button until the desired mode BASS,
TREBLE, FADE or BALANCE appears in the
display. Turn the AUDIO knobto adjust Bass
and Treble to the desired level. Use the Tuning
knobalso to adjust Fader or Balance modes.
Fader adjusts the sound level between the frontand rear speakers and Balance adjusts the
sound between the right and left speakers.
To change the SSV mode to OFF, LOW, MID or
HIGH, turn the Tuning knobto right or left.
To change the NR (Dolby) mode to OFF or ON,
turn the Tuning knobto right or left while cas-
sette tape is playing. When Dolby is ON, the
display indicates the
mark.
Dolby noise reduction is manufactured under
license from Dolby Laboratories Licensing Cor-
poration. Dolby NR and the double-D symbol
“
” are trademarks of Dolby Laboratories
Licensing Corporation.
After 10 seconds, the radio, cassette tape or CD
display reappears. Once the sound quality is set
to the desired level, push the AUDIO button
repeatedly until the radio, cassette tape or CD
display appears.
Display text:
To indicate the text, push the AUDIO knob
during CD or satellite radio playing.
BASS→TREBLE→FADE→BALANCE→
SSV→Display mode
To change the indicated text in display mode,
turn the tuning knobwithin 2 seconds.
Display select:
Display CD text
To indicate the CD text, push the
button
while the CD is playing.
The text will change as follows:
Display MP3/WMA text
To indicate the MP3/WMA text, push the
button while the CD is playing.
The text will change as follows:
Display FM text
To indicate the FM PS name, push the
button while the FM radio is playing.
The name will change as follows:
ON→OFF→ON
When no data is available, “NO TEXT” will
appear.
4-38
Display screen, heater, air conditioner and audio systems


05.8.26/Z50-D/V5.0


Display satellite radio text
To indicate the satellite radio text, push the
button while the satellite radio is playing.
The text will change as follows:
When no data is available, “----” will appear.FM-AM-SAT radio operation
FM/AM/SAT radio select:
The satellite radio mode will be skipped unless
the optional satellite receiver and antenna are
installed, and an XM
or SIRIUS
TM
satellite radio
service subscription is active.
Pushing the RADIO button will change the band
as follows:
AM→FM→SAT (Satellite)
When the RADIO button is pushed while the
ignition switch is in the ACC or ON, the radio will
come on at the station last played.
The last station played will also come on when
the power knobis turned to ON.
If a compact disc or tape is playing when the
RADIO button is pushed, the compact disc ortape will automatically be turned off and the last
radio station played will come on.
The FM stereo indicator ST will glow during FM
stereo reception. When the stereo broadcast
signal is weak, the radio will automatically
change from stereo to monaural reception.
TUNE (Tuning):
WARNING
The radio should not be tuned while
driving so full attention may be given to
vehicle operation.
To tune the radio, turn the TUNE knobto the
right or left.
Use these buttons for manual tuning.
SEEK tuning:
Push the SEEK button
or
for less
than 0.5 second to tune from high to low or low
to high frequencies and stop at the next broad-
casting station (channel).
Push the SEEK button
or
for more
than 0.5 second, to fast tune from high to low or
low to high frequencies.
SCANtuning:
Push the SCAN tuning button to tune from low
to high frequencies and stop at each broadcast-
ing station (channel) for 5 seconds. Pushing the
button again during this 5 seconds period will
stop SCAN tuning and the radio will remain
tuned to that station (channel).
If the SCAN tuning button is not pushed within 5
seconds, SCAN tuning moves to the next station
(channel).
Station memory operations:
Eighteen (18) stations can be set for the FM, AM
and SAT band to the A, B and C preset button.
1. Choose preset channel A, B or C using the
preset select button.
2. Tune to the desired station using the SEEK,
SCAN or TUNE button and keep pushing any
of the desired station memory buttons (1 to
6) until a beep sound is heard. (The radio
mutes when the select button is pushed.)
3. The channel indicator will then come on and
the sound will resume. Memorizing is now
complete.
4. Other buttons can be set in the same manner.
If the battery cable is disconnected, or if the fuse
blows, the radio memory will be erased. In that
Display screen, heater, air conditioner and audio systems
4-39


05.8.26/Z50-D/V5.0