2006 MERCEDES-BENZ ML350 parking brake

445 Practical hints
Replacing bulbs
Have the LEDs and bulbs for the following
lamps replaced by an authorized
Mercedes-Benz Light Truck Center:

Additional turn signals in the exterior
rear view mirrors


Bi-Xenon lamps*


Front fog lamps (vehicles with sport
package*)


High mounted brake lamp
Replacing bulbs for front lamps
Before you start to replace a bulb for a
front lamp, do the following first:
Turn the exterior lamp switch to
positionM (
page 138).

Open the hood (
page 326).
1Housing cover for low beam halogen or
Bi-Xenon* headlamp
2Housing cover for high beam halogen
bulb (vehicles with halogen bulbs: high
beam and high beam flasher; vehicles
with Bi-Xenon* headlamps: high beam
flasher only)
3Bulb socket for parking and standing
lamp bulb
4Bulb socket for turn signal lamp bulb
5Bulb socket for side marker lamp bulb

451 Practical hints
Replacing bulbs
Example rear lamp passenger-side1Brake lamp
2Backup lamp
3Rear fog lamp (only driver’s side), tail
lamp, parking and standing lamp
4Side marker lamp
5Turn signal lamp
Turn the respective bulb socket with
the bulb counterclockwise and remove
it.

Press gently onto the respective bulb
and turn counterclockwise out of its
bulb socket.

Press the new bulb gently into its bulb
socket and turn clockwise until it en-
gages.

Align bulb socket and turn it clockwise.
License plate lamp
1License plate lamp cover
2Screw

Loosen both screws2.

Remove license plate lamp cover1.

Replace the tubular bulb.

Reinstall license plate lamp cover1.

Retighten screws2.
Adjusting headlamp aim
VVertical centerline
HHeadlamp mounting high, measured
from the center
iHigh beam adjustments simultaneous-
ly aim the low beam.
Vehicle should have a normal tailgate
load.

456 Practical hintsFlat tire
Preparing the vehicle
Park the vehicle as far as possible from
moving traffic on a hard surface.

Turn on the hazard warning flashers.

Turn the steering wheel so that the
front wheels are in a straight ahead po-
sition.

Set the parking brake.

Shift automatic transmission to park
positionP.
Vehicles with Air suspension package*:

Do not open or close a door or tailgate
while mounting the spare wheel.
Vehicles with SmartKey:

Turn off the engine (
page 34).

Remove the SmartKey from the starter
switch.Vehicles with KEYLESS-GO*:

Turn off the engine by pressing the
KEYLESS-GO* button once
(page 63).

Open the driver’s door (this puts the
starter switch in position0, same as
with the SmartKey removed from the
starter switch). The driver’s door then
can be closed again.

Have any passenger exit the vehicle at
a safe distance from the roadway.
Warning!
G
The dimensions of the Minispare wheel are
different from those of the road wheels. As
a result, the vehicle handling characteristics
change when driving with a mounted
Minispare wheel. Adapt your driving style
accordingly.
The Minispare wheel is for temporary use
only. When driving with a Minispare wheel
mounted, ensure proper tire pressure and
do not exceed a vehicle speed of
50 mph (80 km/h).
Drive to the nearest Mercedes-Benz Light
Truck Center as soon as possible to have the
Minispare wheel replaced with a regular
road wheel.
Never operate the vehicle with more than
one spare wheel mounted.
Do not switch off the ESP
® when a
Minispare wheel is mounted.
iOpen doors only when conditions are
safe to do so.

457 Practical hints
Flat tire
Mounting the spare wheel
Preparing the vehicle
Prepare the vehicle as described
(page 456).

Take the wheel wrench, the collapsible
wheel chock, and the vehicle jack out
of the cargo compartment
(page 430).

Take the Minispare wheel out of the
cargo compartment (
page 433).Lifting the vehicle

Prevent the vehicle from rolling away
by blocking wheels with wheel chocks
or other sizable objects.
A collapsible wheel chock is included
with the vehicle tool kit (
page 430).
For information on setting up the col-
lapsible wheel chock, see
(
page 432).
When changing wheel on a level surface:

Place one wheel chock in front of and
another sizeable object behind the
wheel that is diagonally opposite to the
wheel being changed.
Always try lifting the vehicle using the jack
on a level surface. However, should
circumstances require you to do so on a
hill, place the wheel chock and other size-
able object as follows:

Place the wheel chock and another
sizable object on the downhill side
blocking both wheels of the axle not
being worked on.
!Vehicles with factory-mounted
running-boards*:
Your vehicle is equipped with a scis-
sors-type jack (located under the cargo
compartment floor) designed for use
with factory-mounted running boards.
Only use this jack when jacking up ve-
hicles with factory-mounted running
boards as otherwise the vehicle’s
underbody can be damaged. See sepa-
rate instructions for scissors-type jack.
Warning!
G
The jack is designed exclusively for jacking
up the vehicle at the jack take-up brackets
built into both sides of the vehicle. To help
avoid personal injury, use the jack only to lift
the vehicle during a wheel change. Never
get beneath the vehicle while it is supported
by the jack. Keep hands and feet away from
the area under the lifted vehicle. Always
firmly set parking brake and block wheels
before raising vehicle with jack.
Do not disengage parking brake while the
vehicle is raised. Be certain that the jack is
always vertical (plumb line) when in use, es-
pecially on hills. Always try to use the jack
on level surface. Make sure that the jack
arm is fully seated in the jack take-up brack-
et. Always lower the vehicle onto sufficient
capacity jackstands before working under
the vehicle.

465 Practical hints
Battery
Step 1 (Disconnecting)

Turn off the engine and leave the igni-
tion switched on (
page 34).

Depress parking brake firmly and set
automatic transmission to positionP.

Turn off all electrical consumers.

Read and observe safety instructions
and precautions (
page 462).

Move the front passenger seat to the
most forward position (
page 39).
Step 2 (Disconnecting)
1Battery cover

Enter the rear passenger compartment
and remove main battery cover1.Step 3 (Disconnecting)
2Perforated floor carpet

Cut the floor carpet2 along the
dotted white line (see illustration) until
you reach the perforated part. Start
cutting at the point indicated by the
arrows. Cut carpet using a sharp object
(knife etc.).

Enter the front passenger compart-
ment.

Move the front passenger seat to the
most rearward position (
page 39).
iWith a disconnected battery you will no
longer be able to turn the SmartKey in
the starter switch and pressing the
KEYLESS-GO* start/stop button will
have no effect.iIf your battery is discharged, the vehi-
cle must be jump started (
page 470)
using the jump start contacts in the
engine compartment, or an accessory
battery charge unit* approved by
Mercedes-Benz must be connected
using the jump start contacts in the
engine compartment (see separate
instructions for the accessory battery
charge unit*) before any of the follow-
ing steps can be performed. If the
battery cannot be jumped or charged,
please contact an authorized
Mercedes-Benz Light Truck Center.


471 Practical hints
Jump starting
The jump-start contacts are located in the
engine compartment.
Make sure the two vehicles do not
touch.

Turn off all electrical consumers.

Apply parking brake.

Shift gear selector lever to positionP.1Negative (-) terminal
2Cover of Positive (+) terminal

Open cover2 of the positive terminal
of both vehicles.

Connect positive terminal2 and the
positive terminal of the charged battery
with the jumper cable. Clamp cable to
charged battery first.

Start engine of the vehicle with the
charged battery and run at idle speed.

Connect negative terminals1 and the
negative terminal of the charged
battery with the jumper cable. Clamp
cable to charged battery first.

Start the engine of the disabled vehi-
cle.
Now you can again turn on the electrical
consumers. Do not turn on the lights under
any circumstances.

Remove the jumper cables first from
the negative terminals on each battery
and then from the positive terminals on
each battery.
Now you can turn on the lights.

Have the battery checked at the near-
est authorized Mercedes-Benz Light
Truck Center.
Warning!
G
Keep flames or sparks away from battery.
Do not smoke.
Observe all safety instructions and precau-
tions when handling automotive batteries
(page 462).!Never invert the terminal connections!
iThe message
Undervoltage - Switch
off consumers may appear in the
instrument cluster. It will disappear as
soon as the battery is sufficiently
charged.
!Do not tow-start the vehicle.

510 IndexBrake pads
Message in display 408
Brakes 300
Warning lamp 383
Break-in period 298
Bulbs, replacing 443
Additional turn signals 443
Backup lamps 444
Brake lamps 444
Fog lamps 443
Front fog lamp 449
Front lamps 443
High beam 443
License plate lamps 444, 451
Low beam 443
Parking, standing lamp 443
Rear fog lamps 450
Rear side marker lamp bulbs 450
Side marker lamp 443
Side marker lamps 444
Turn signal lamps 443, 444C
CAC (Customer Assistance Center) 501
Calibrating
Compass 171
California
Important notice 11
Call priority
Tele Aid* 287
Calling up
Range (distance to empty) 178
Service indicator 372
CAN system 501
Capacities
Fuels, coolants, lubricants, etc. 493
Cargo compartment
Fuse box in 479
Interior lighting 145
Lamp 147
Tie-down rings 260
Cargo compartment cover* 265
Closing 265
Installing 265
Opening 265
Removing 265
Cargo tie-down rings 260Carpet
Cleaning 379
Catalytic converter 320
CD player
Operating 158
Center console 27
Lower part 28
PASS AIR BAG OFF indicator
lamp 393
Upper part 27
Central locking
Automatic 125
Switch 126
Switching on/off
(control system) 172
Unlocking from inside 126
Central locking switch 126
Certification label 484
Changing
SmartKey setting 173
Charging
Vehicle battery 469
CHECK ENGINE malfunction
indicator lamp 385, 386

519 Index
L
Labels, identification 484
Lamp bulbs, exterior 443
Lamps, exterior
Front 443
Light sensor 420
Messages in display 418, 420
Rear 444
Lamps, indicator and warning
ABS 382
Air bag Off 72
Battery (SmartKey with
KEYLESS-GO*) 114
Battery (SmartKey) 108
Brakes 383
CHECK ENGINE 385, 386
CHECK Engine malfunction
indicator lamp 386
Engine diagnostics 385, 386
ESP
®
387
Front fog lamps 138
Fuel reserve 388
Rear fog lamp 138
Seat belts 388, 389
SRS 390Language
Multifunction display 164
Setting 164
LATCH type child seat anchors 88
LATCH type child seat mounts 88
Layout of poly-V-belt drive (ML 350) 485
Layout of poly-V-belt drive (ML 500) 485
Leather upholstery*
Cleaning 380
Lever
For cruise control 238
License plate lamps
Messages in display 419
Replacing bulbs 444, 451
Light alloy wheels
Cleaning 379
Light sensor 420
Lighter see cigarette lighterLighting 138
Automatic headlamp mode 139
Cargo compartment lamp 147
Daytime running lamp mode 140
Door entry lamps 147
Front fog lamps 142
High beams 142
Instrument cluster illumination 148
Interior 145
Locator lighting 141
Low beam 138
Manual headlamp mode 139
Night security illumination 141
Parking lamps 138
Rear fog lamp 142
Settings (control system) 167
Standing lamps 138
Limiting the gear range 187
Limp Home Mode 192
Line of fall 503