2006 MERCEDES-BENZ E-Class navigation system

133 Navigation*
Route guidance
If available, the street following the driving
maneuver with its name is shown in the top
status bar (here
CHESTNUT RIDGE RD).
The destination is marked with a flag on
the map, any stop-over destination is
marked with a flag .
Changing map scale
The currently selected map scale is shown
in the left-hand corner of the bottom status
bar .
Press any soft key.
The soft key displays appear.
Press the or soft key.
Depending on your selection, the map
will zoom in and display greater detail
or zoom out and show a wider area.
The map scale bar in the status bar will
show the map scale currently selected.
Map orientation
During route guidance, a symbol will ap-
pear on the left of the bottom status bar if
map display is switched ON:
North symbol :
Fixed map orientation, north is always
pointing up;
or
Compass symbol :
Dynamic map orientation, driving direc-
tion is always pointing up.
Map orientation can be set manually
(
page 143).
s
i
The display unit can be changed to km
or miles using the control system (see
your vehicle Operator's Manual).
When the display unit is set to miles,
COMAND will indicate distances in
miles (mi) or feet (ft).
When the display unit is set to km,
COMAND will indicate distances in kilo-
meters (km) and meters (m).
i
If no soft key is selected within
approx. 8 seconds, the soft key display
will disappear.

134 Navigation*
Route guidance
Changing map display
The map display can be switched between
split-screen mode and full-screen mode
manually or automatically.
Split-screen mode
The map is shown on the left, while in-
formation concerning the next driving
maneuver is shown on the right.
Full-screen mode
The map covers the entire screen.
Switching manually
Press.
Each time  is pressed, the system
alternates between split-screen and
full-screen display mode.
Switching automatically
See “Automatic map toggling”
(
page 145).Route guidance ends when the selected
destination is reached.
In navigation mode, press .
A prompt as to whether or not route
guidance is to be cancelled appears.
Use to select the menu item Yes.
Press .
Route guidance is cancelled. After a
short time, the Navigation main menu
appears.
i
Information concerning the current lo-
cation is shown in the status bar if GPS
display (
page 144) and full-screen
display are activated.
Destination reached
Cancelling route guidance
i
Route guidance can be continued again
in the Navigation main menu
(
page 110).

136 Navigation*
During route guidance
1Estimated time of arrival
2Remaining driving time in hours and
minutes
3Remaining journey (distance)
Points 1, 2 and 3 refer to the stop-
over destination. You'll only see the de-
tails for the final destination when you
arrive at your stopover and the system
has calculated the route to the main
destination.Selectable soft keys:Route soft key
Provides access to the display of the
route on the map (
page 136).
Mode soft key
Provides access to the route mode set-
ting for certain road types to be avoid-
ed (
page 111).
In the Info menu (page 135), press
the
Route soft key.The map appears. The route remaining
is highlighted in blue color.
The destination is marked with a flag
, any stop-over destination is marked
with a flag . The current vehicle posi-
tion is identified with the symbol.
Depending on the distance to the des-
tination, it may take some time before
the route display appears.
i
The estimated time of arrival does not
refer to the time zone of destination,
but always refers to the time zone of
the vehicle's current location. For a
correct calculation, make sure that the
system clock is set correctly
(
page 162).
Displaying the route on the map
s

137 Navigation*
During route guidance
In the Info menu (page 135), press
the
Route soft key.
The route appears on the map.
Press the List soft key.
The list of road/route sections remain-
ing appears. The road currently trav-
elled on appears at the top.
Use or  to scroll through the
list. The
Page soft keys allow scrolling
through the list page by page.The Detour function blocks a route seg-
ment ahead.
The length of this route segment can be
entered. The system then calculates a de-
tour route, if possible.
Show the soft key displays
(
page 135).
The Detour soft key display indicates
whether the Detour function is active.
= not active
= activeDetour function is not active
You can activate the function and set the
length of a route segment to be blocked
(
page 137).
Detour function is already active
You can change the length of the route
segment to be blocked (
page 138), or
switch off the Detour function by deleting
the detour (
page 138).
Activating detour function and setting
length of route segment to be blocked
Show the soft key displays
(
page 135).
Press the Detour soft key.
The system gives you a full-screen map
and freezes the map and screen show-
ing the position of the vehicle. You can
now set the distance of the route seg-
ment to be blocked.
Displaying the route listi
Depending on the distance to the des-
tination, it may take a few moments be-
fore the route list is completed.
The list is completed only when the
route calculation is completed.
Dest. is
displayed before the last list entry.
Detour function


138 Navigation*
During route guidance
Continue to press the soft key More or
Less until the desired distance for the
route segment to be blocked is
reached.
The length of the route segment
blocked ahead appears in the status
bar. The section of the road that is
blocked appears as a red and white
dotted line on the map.
1Symbol = current position
Press .
The system calculates a new route
avoiding the blocked road segment.Changing detour
Show the soft key displays
(
page 135).
Press the Detour soft key.
Use to select the Change detour
menu item.
Press.
You can now enter the length of the
road segment to be blocked.
Continue to press the More or Less soft
key until the desired distance for the
route segment to be blocked is set.
Press.
The system calculates a new route
avoiding the blocked segment, if possi-
ble.
Deleting detour
Show the soft key displays
(
page 135). If a Detour is already active, the
Detour
soft key is displayed in no color.
Press the Detour soft key.
Use  to select the Delete detour
menu item.
Press.
The blocked road segment or detour re-
quirement is cancelled. The system re-
calculates the route.

139 Navigation*
During route guidance
This function offers the option of selecting
a stop-over destination while route guid-
ance is active.
A stop-over destination can be, for exam-
ple, a gas station, a rest area, or a hospital.
Once the stop-over destination has been
reached, the system automatically calcu-
lates the route to the final destination.
Show the soft key displays
(
page 135). The
St-over soft key display indicates
whether the stop-over function is ac-
tive.
= not active
= active
Route guidance to a stop-over destination
is not active:
You can enter a stop-over destination
(
page 139).
Route guidance to a stop-over destination
is already active:
You can change the stop-over destination
or cancel the route guidance to it by delet-
ing the stop-over (
page 141).
Entering an stop-over destination
Show the soft key displays
(
page 135).
Press the St-over soft key.
The full-screen map display appears.Selectable soft keys
 soft key:
Provides access to a list of Mercedes-
Benz Centers in the area.
 soft key:
Provides access to a list of gas stations
in the area.
 soft key:
Provides access to a
list of parking areas
and multi-story car parks in the area.
Stop-over


141 Navigation*
During route guidance
Press the Details soft key, if you want to
see details of the selected destination.
The details disappear again after
approx. 3 seconds, or when pressing
the
Details soft key again.
Press  to confirm the selection of a
destination.
The system begins to calculate the
route to the selected stop-over destina-
tion.
Changing/deleting stop-over destina-
tions
Show the soft key displays
(
page 135).
.
Press the St-over soft key.
The menu for deleting or changing the
stop-over destination appears.
Use to select the
Delete active stopover entry.
Press .
This will delete the stop-over. The sys-
tem calculates the route to the final
destination;
or
Use to select the
Replace active stopover entry.
Press .
The stop-over is deleted, a new stop-
over destination can be entered
(
page 139).
i
A stop-over destination can be
changed or deleted only while the route
guidance to this stop-over is active (in-
dicated by ).
i
If no route guidance to a stop-over des-
tination is active yet (
page 139).

142 Navigation*
During route guidance
Show the soft key displays
(
page 135).
Press the Display soft key.
The Display menu appears.
Selectable soft keys:
Symbols soft key
Provides access to setting the symbols
display (
page 142).
View soft key
Provides access to setting the map ori-
entation (
page 143).
GPS soft key
Provides access to the Position Display
menu (
page 144).
Auto soft key
Provides access to the Automatic Map
Switching menu (
page 145).
Zoom soft key
Provides access to the definition of the
scales for full-screen and split-screen
map display (
page 145).
You can select which POIs will appear as
symbols on the map.
In the Display menu (page 142)
press the
Symbols soft key.
The available options appear.
Use  or to select an option.
Press.
The selected option is activated. A solid
circle designates an activated op-
tion.
Standard option:
The symbols for the system default
setting are displayed on the map.
Defining route guidance displays
Setting symbols displays
i
The symbols are on display only if the
map scale is set at 0.05 mi (50 m),
0.1 mi (100 m), 0.2 mi (200 m), or
0.5 mi (500 m).
To set the map scale (
page 133).