2006 MERCEDES-BENZ CLS55AMG battery

351 Practical hints
What to do if …
Where will I find ...?
Unlocking/locking in an emergency
Opening/closing in an emergency
Resetting activated head restraints
Replacing SmartKey batteries
Replacing bulbs
Replacing wiper blades
Flat tire
Battery
Jump starting
Towing the vehicle
Fuses

352 Practical hintsWhat to do if …Lamps in instrument clusterGeneral information:
If any of the following lamps in the instru-
ment cluster fails to come on during thebulb self-check when switching on the igni-
tion, have the respective bulb checked and
replaced if necessary.Problem
Possible cause/consequence
Suggested solution
-
The yellow ABS indicator lamp
comes on while driving.
The ABS has detected a malfunction and has
switched off. The BAS and the ESP
® are also
switched off (see messages in multifunction
display).
The electro-hydraulic brake system is still
functioning normally but without the ABS
available.
If the ABS control unit is malfunctioning, oth-
er systems such as the Parktronic system*,
Distronic*, or the automatic transmission
may also be malfunctioning.

Continue driving with added caution.
Wheels may lock during hard braking,
reducing steering capability.

Read and observe messages in the
multifunction display (
page 363).

Have the system checked at an autho-
rized Mercedes-Benz Center as soon
as possible.
Failure to follow these instructions in-
creases the risk of an accident.
The charging voltage has fallen below
10 volts. The ABS has switched off.
The battery may not be sufficiently charged.

Switch off electrical consumers that
are currently not needed, e.g. seat
heating.

If necessary, have the generator and
battery checked.
When the voltage is above this value
again, the ABS is operational again.

369 Practical hints
What to do if …
Display message
Possible cause/consequence
Possible solution
ESP
Display malfunction
Visit workshop
The ESP
® or the ESP
® display is mal-
functioning.

Continue driving with added caution.

Have the system checked at an authorized
Mercedes-Benz Center as soon as possible.
Failure to follow these instructions increases the
risk of an accident.
P
Gear selector lever
in Park
You have attempted to turn off the
engine with the KEYLESS-GO*
start/stop button with the gear
selector lever not inP. You have
opened the driver's door with the
gear selector lever not inP.

Place the gear selector lever in positionP.
P/N
Shift to
Neutral or Park
You have attempted to start the
engine with the KEYLESS-GO*
start/stop button while the gear se-
lector lever was in positionR orD.

Place the gear selector lever in positionP
orN. Make sure the brake pedal is depressed.
Low Battery

Conven. functions
temporarily
unavailable
The battery has insufficient voltage
and can no longer supply conve-
nience functions such as the rear
window defroster.
As soon as the on-board voltage is sufficient, the
consumers will switch on again.

372 Practical hintsWhat to do if …Display messages
Possible cause/consequence
Possible solution
Tire pres. monitor
inoperative
No wheel sensors
There are wheels without wheel sen-
sors mounted (e.g. winter tires).

Have the Advanced TPMS* checked by an au-
thorized Mercedes-Benz Center.

Have the wheel sensors installed by an
authorized Mercedes-Benz Center.
Tire pres. monitor
Wheel sensor missing


One or more sensors malfunc-
tion (e.g. battery is empty).


One or more wheels without
wheel sensors mounted (e.g.
spare tire).
The tire inflation pressure for the re-
spective tire is not shown in the mul-
tifunction display.

Have the Advanced TPMS* checked by an au-
thorized Mercedes-Benz Center.

Have the wheel sensors installed by an
authorized Mercedes-Benz Center.

373 Practical hints
What to do if …
Symbol messagesDisplay symbol
Display messages
Possible cause/consequence
Possible solution
#
Low voltage
Switch off
consumers
The battery has insufficient voltage.

Turn off unnecessary electrical con-
sumers.
Visit workshop
The battery is no longer charging.
Possible causes:

alternator malfunctioning


broken poly-V-belt
Do not forget that the brake system
requires electrical energy and may be
operating with restricted capability.
Considerably greater brake pedal force is
required and the stopping distance is
increased.

Stop immediately in a safe location or
as soon as it is safe to do so and
check the poly-V-belt.
If it is broken:

Do not continue to drive. Otherwise
the engine will overheat due to an
inoperative water pump which may re-
sult in damage to the engine. Notify
an authorized Mercedes-Benz Center.
If it is intact:

Drive immediately to the nearest
authorized Mercedes-Benz Center.
Adjust driving to be consistent with
reduced braking responsiveness.

374 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause/consequence
Possible solution
#
Battery/Alternator
Stop vehicle
The battery is malfunctioning.
The electro-hydraulic brake system re-
quires electrical energy and therefore has
only limited operation. Considerably
greater brake pedal force is required and
the stopping distance is increased.

Stop the vehicle as soon as it is safe
to do so. Adjust driving to be consis-
tent with reduced braking responsive-
ness.

Notify an authorized Mercedes-Benz
Center.
Low voltage
Start engine
The battery has insufficient voltage.

Start the engine (
page 49).
2
Brake wear
Visit workshop
The brake pads have reached their wear
limit.

Have the brake pads replaced as soon
as possible.
!Brake pad thickness must be visually
inspected by a qualified technician at
the intervals specified in the
Maintenance Booklet.

375 Practical hints
What to do if …
Display symbol
Display messages
Possible cause/consequence
Possible solution
!
Release parking
brake
You are driving with the parking brake
set.

Release the parking brake
(page 51).
T
Reduced braking power
Depress brake
pedal fully
The electro-hydraulic brake system is in
emergency operation mode. Consider-
ably greater brake pedal force is required
and the stopping distance is increased.
The maximum speed is limited to 55 mph
(90 km/h).

Do not drive any further.

Stop the vehicle in a safe location and
notify an authorized Mercedes-Benz
Center.

Prevent the vehicle from rolling away
by blocking the wheels with wheel
chocks or other sizable objects.

Call for Roadside Assistance.
(USA only);(Canada only)3
Reduced braking power
Start engine
The battery has insufficient voltage and
cannot supply sufficient power to the
electro-hydraulic brake system.

Start the engine.
The message disappears when suffi-
cient voltage is available.

386 Practical hintsWhat to do if …Display symbol
Display messages
Possible cause/consequence
Possible solution
F
Key
Check battery
The SmartKey with KEYLESS-GO* batter-
ies are discharged.

Change the batteries (
page 408).
Key
not recognized
The SmartKey with KEYLESS-GO* is not
recognized while the engine is running
because

the SmartKey with KEYLESS-GO* is
not in the vehicle


there is strong radio-frequency inter-
ference

Stop the vehicle as soon as it is safe
to do so.

Search for the SmartKey.
Otherwise the vehicle cannot be cen-
trally locked nor can the engine be
started again after the engine is
stopped.
Key
not recognized
The SmartKey with KEYLESS-GO* is mo-
mentarily not recognized.

Change the position of the SmartKey
in the vehicle.

Operate the vehicle with the
SmartKey in the starter switch if nec-
essary.