2006 MERCEDES-BENZ CLS-Class audio

41 Audio
Radio operation
Tuning via direct frequency input
Entry example:
98.5 MHz in FM waveband
Switch to the FM waveband
(
page 37).
Press.The frequency input display appears.
The frequency range of the FM wave-
band is shown.
Press the number buttons in
succession:, , and .
Each number entered appears in the
display.
The system tunes to the frequency en-
tered (in this example: 98.5 Mhz) and
switches back to the FM menu.Tuning via station search
Seven channels are available on the
Weather Band.
On COMAND control unit
Switch to the WB waveband by press-
ing the
WB soft key in the Radio main
menu (
page 37).
i
Manual tuning is also possible in all
wavebands by pressing or .
The frequency will change by the tuning
increments for the respective wave-
band each time one of the buttons is
pressed.
Frequency increments for manual
tuning:
FM 0.2 MHz
AM 10 kHz
i
Entries outside the frequency range are
not possible.
Within the AM waveband, the input is
restricted to frequencies within the re-
spective frequency increment, which
is10 kHz.
The system will select the nearest valid
frequency if a frequency outside the
frequency increment is entered.
Tuning to a station on Weather Band


42 Audio
Radio operation
The system will tune to the strongest
receivable station.
Press  or.
Search begins in ascending or
descending frequency.
The search stops at the next receivable
station.
On multifunction steering wheel
Switch the multifunction display in the
instrument cluster to Radio display
(
page 25).
Pressj ork.
The search stops at the next receivable
station. Tuning via station presets
The seven strongest channels are sorted in
prest 1 to 7 each time you press the
WB soft
key. They are accessed using the number
keypad.
Press one of the number keys
 - .
The system tunes to the station stored
under this number.
Ten presets each are available for the
FM and AM waveband.
The following options are available:
Storing manually using number keys
Storing manually using the Presets
menu
Storing using Autostore Storing manually using the number
keys  - 
Tune to the station to be stored
(
page 38).
Press a number key between and
 and hold it for more than 2 sec-
onds.
The station is now stored in the respec-
tive memory location.
Storing manually using the Presets
menu
Tune to the station to be stored
(
page 38).
Press the Presets soft key.
The Presets menu appears.
Storing FM/AM stations

43 Audio
Radio operation
Use, ,  or  to select a
preset.
Press for more than 2 seconds.
The station will be stored in the respec-
tive memory location.
Storing using Autostore
The Autostore function places stations into
the Autostore memory sorted by reception
quality.
The system stores the station with the
strongest signal in preset 1.
Switch to the desired waveband
(
page 37).
Press the Autost. soft key.
The Autostore preset list appears.
Use to select the
Reprogram Autostore header entry.
Press.
The Autostore search starts. After a de-
lay the new preset assignment ap-
pears. The system tunes to the station
stored on preset 1.
To tune-in another station from the
Autostore preset list (
page 39).
i
The Autostore feature stores presets in
a separate memory, not in the regular
presets seen under the
Presets soft key.
As such, the Autostore memory is only
temporary.

44 Audio
Single CD operation
Only touch the CD on the edges.
Clean the CD with a dry, lint-free cloth.
Wipe the CD a straight line from the
center. Never wipe the CD in a circular
motion.
Do not use rubbing alcohol or solvents
to clean CDs.
Do not expose the CDs to heat or direct
sunlight.
Do not write or put labels on CDs
Safety Instructions
WarningG
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and
operate the audio system only when road,
weather and traffic conditions permit.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
Warning G
The CD drive is a Class 1 laser product.
There is a danger of invisible laser radiation
when you open or damage the cover.
Do not remove the cover. The CD drive does
not contain any parts serviceable by the us-
er. For safety reasons, have any necessary
service work performed by qualified person-
nel.
Tips on caring for your CDs

45 Audio
Single CD operation
Open the Single CD main menu
(
page 46).
or
Load an audio CD into the COMAND
CD drive.
Switching to Single CD mode
Loading a CD
WarningG
In order to avoid distraction which could
lead to an accident, the driver should insert
CDs with the vehicle at a standstill and oper-
ate the audio system only when road, weath-
er and traffic conditions permit.
Bear in mind that at a speed of just 30 mph
(approximately 50 km/h), your vehicle is
covering a distance of 44 feet (approximate-
ly 14 m) every second.
!
Do not attach labels of any type to the
CD. They may become detached and
damgage the drive.
Only use CDs, which bear the label
shown and that conform to the com-
pact digital audio standard
(IEC 60908).
Do not play single-CDs (80 mm) with an
adapter. Only use round, 12 cm diame-
ter CDs.
!
Your CD drive has been designed to
play CDs which correspond to the IEC
60908 standard. Therefore only CDs
not exceeding a thickness of 1.3 mm
can be used.
If you insert thicker data carriers, e.g.
ones that have data on both sides (one
side with DVD data, the other side with
audio data), they cannot be ejected
and will damage the drive.
i
The COMAND CD drive may not be able
to play audio CDs with copy protection.

46 Audio
Single CD operation
The COMAND CD drive holds one CD. The
slot for inserting a CD is located above the
display (
page 15).
Insert a CD into the CD slot while
COMAND is switched ON. Insert the
CD face up.
COMAND pulls in the CD. If the CD is
an audio CD, the system switches to
Single CD mode.
Press.
COMAND ejects the CD.
Remove the CD from the slot.
The CD will be pulled in again if it is not
removed from the slot within approx. 7
seconds.
Open the Audio main menu
(
page 36).
Press the CD soft key.
The system switches to Single CD
mode.The center of the status bar shows: The track number and total number
of tracks
The elapsed playing time of the
track
!
If a CD is already loaded, it must be
ejected before inserting the new CD.
Inserting a second CD in the slot with
another CD still loaded will cause dam-
age to the CD drive not covered by the
Mercedes-Benz Limited Warranty.
i
If the CD is an MP3 CD, the system
switches to MP3 mode (
page 53).
Ejecting a CD
Single CD main menu
i
The CD soft key is shaded out if no audio
CD is loaded. The system will not
switch to Single CD mode.
Load an audio CD into the
COMAND CD drive (
page 45).
The
MP3 soft key instead of the CD soft
key is visible when a MP3 CD has been
loaded.

47 Audio
Single CD operation
1Track title or track number
2Elapsed track playing time
3Track number/total tracks
The Single CD main menu shows the track
title in the center if the CD contains corre-
sponding CD text data.
If the CD does not contain any CD text da-
ta, the track number is displayed instead of
the track title. The following options are available:
Selecting via track skip
Selecting via track list
Selecting via manual entry of the track
number (
page 48)
Selecting via scan search (page 48)
Selecting via track skip
On the COMAND control unit
Open the Single CD main menu
(
page 46).
Pressfor forward skipping.
or
Press for backward skipping.On the multifunction steering wheel
Switch the multifunction display in the
instrument cluster to the Single CD dis-
play (
page 25).
Pressj for forward skipping.
or
Pressk for backward skipping.
Selecting a track
i
Forward skipping:
The next track is played.
Backward skipping:
The system skips back to the beginning
of the track if more than approx. 10
seconds playing time of the track cur-
rently playing have elapsed.
The system skips back to the beginning
of the previous track if less than 10
seconds playing time of the track cur-
rently playing have elapsed.

48 Audio
Single CD operation
Selecting via track list
The track list contains all tracks of the cur-
rent CD. Only one list entry is visible at a
time, it is the track currently playing.
Use or  to select another track
from the list.
Press, or wait approx. 3 seconds
without changing the selection.
The selected track is played.Selecting via manual entry of the track
number
Open the Single CD main menu
(
page 46).
Press.
The Manual track input display ap-
pears. The number of tracks on the CD
is displayed.
Entry example: Track 1
Press.Entry example: Track 12
Press and  in quick succession.
Wait approx. 3 seconds after entering
the number.
The selected track is played. The CD
main menu appears.
Selecting via scan search
Scan serach is charcterised as follows:
Scan search plays each track on the
current CD for approx. 8 seconds.
Scan search can be ended manually.
Scan search automatically stops at the
track listened to before the scan
search was started.
i
Entries beyond the number of available
tracks on the CD are not possible.