2006 LEXUS LX470 lock

INTERIOR EQUIPMENT
79
Programming an entrance gate /
Programming all devices in the Canadian
market
1. Decide which of the 3 HomeLink buttons you want to
program.
2. Place your hand −held gate/device transmitter 25 to 75 mm
(1 to 3 in.) away from the surface of the HomeLink
.
Keep the indicator light on the HomeLink
 in view while
programming.
3. Press and hold the selected HomeLink
 button.
4. Continuously press and release (cycle) the hand−held
gate/device transmitter button every two seconds until step 5
is complete.
5. When the indicator light on the HomeLink
 changes from a
slow to a rapid flash after 20 seconds, you can release both
buttons.
6. Test the operation of the HomeLink
 by pressing the newly
programmed button. Check to see if the gate/device operates
correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink

button to program another device.
Programming other devices
To program other devices such as home security systems,
home door locks or lighting, contact your authorized Lexus
dealer for assistance.
Reprogramming a button
Individual HomeLink buttons c annot be erased, however, to
reprogram a single button, follow the procedure “Programming
the HomeLink
”.
(b) Operating the HomeLink
To operate the HomeLink, press the appropriate HomeLink
button to activate the programmed device. The HomeLink
indicator light should come on. The HomeLink continues to
send the signal for up to 20 seconds as long as the button is
pressed.

INTERIOR EQUIPMENT
82
14X080a
To use a cupholder in the console box,
1. Open the console box lid. Pull down the knob so that
the cupholder swings down.
2. While holding the console box lid with your hand, push
down the cupholder to be secured.
NOTICE
 When you use the cupholder in the console box,
make sure it is securely locked.
 Do not rest your arm on the cupholder in the console
box.
 Wipe up spilt drink at once.
Rear
14X020b
Rear end of the rear console
14X024
Leftside trim panel near the third seat
To use the cupholder, push or pull out the cupholder lid.

INTERIOR EQUIPMENT
85
FLOOR MAT
14X008d
Use a floor mat of the correct size.
If the vehicle carpet and floor mat have 2 holes, then they are
designed for use with locking clips. Attach the floor mat to the
vehicle carpet using the clips. Lock the clips into the holes in
the vehicle carpet.
14X009a
CAUTION
Make sure the floor mat is properly placed on the vehicle
carpet. If the floor mat slips and interferes with the
movement of the pedals during driving, it may cause an
accident.

INTERIOR EQUIPMENT
89
Adjusting the position of cross rails
14x507a
 1Side knobs 2Upper knob
1. Turn the upper and side knobs counterclockwise to
loosen the cross rails.
14x508a
2. Slide the cross rails to the appropriate position for
loading the luggages and turn the side knobs clockwise
to tighten the cross rails securely.
There are cross rail stoppers on the roof rails which help you
prevent the cross rails being touched with the tilted −up moon
roof.
NOTICE
Do not remove the cross rail stoppers, or the moon roof
may be damaged when it is tilted.

INTERIOR EQUIPMENT
90
14x509a
3. In order to fix the cross rails to the appropriate length,
turn the upper knobs clockwise after tightening all the
side knobs.
CAUTION
Make sure the cross rails are fixed securely by pushing
forward and rearward them. Failure to do so may cause
an accident or severe injury in the event of emergency
braking or a collision.
Follow the manufacturer’s instructions and precautions when
installing the attachments or their equivalent.
CAUTION
When you load cargo on the roof luggage carrier,
observe the following:
 Place the cargo so that its weight is distributed
evenly between the front and rear axles.
 If loading long or wide cargo, never exceed the
vehicle overall length or width. (See “Specifications”
on page 463 for information on your vehicle overall
length and width.
 Before driving, make sure the cargo is securely
fastened on the roof luggage carrier.
 Loading cargo on the roof luggage carrier will make
the center of the vehicle gravity higher. Avoid high
speeds, sudden starts, sharp turns, sudden braking
or abrupt maneuvers, otherwise it may result in loss
of control or vehicle rollover due to failure to operate
this vehicle correctly.
 If driving for a long distance, on rough roads, or at
high speeds, stop the vehicle now and then during
the trip to make sure the cargo remains in its place.
 Do not exceed 70 kg (143 lb.) cargo weight on the roof
luggage carrier.
NOTICE
When loading the luggages, be careful not to scratch
the surface of the moon roof.

EXTERIOR EQUIPMENT
92
HOOD
15X001a
1. To open the hood, pull the hood lock release lever
under the instrument panel. The hood will spring up
slightly.
15X014c
2. Insert your fingers under the hood, push up the
auxiliary catch lever and lift the hood.
Before closing the hood, check to see that you have not
forgotten any tools, rags, etc. Then lower the hood and make
sure it locks.
CAUTION
Before driving, be sure that the hood is closed and
securely locked. Otherwise, the hood may open
unexpectedly while driving and an accident may occur.

EXTERIOR EQUIPMENT
94
15X004a
2. To remove the fuel tank cap, turn the cap slowly
counterclockwise, then pause slightly before removing it.
The removed cap can be stored on the back side of the fuel
filler door.
It is not unusual to hear a slight swoosh when the cap is
opened. When installing the cap, turn the cap clockwise until
you hear a click.
If the cap is not tightened securely, the malfunction indicator
lamp comes on. Make sure the cap is tightened securely.
The indicator lamp goes off after driving several times. If the
indicator lamp does not go off, contact your Lexus dealer as
soon as possible.
CAUTION
 Make sure the cap is installed securely to prevent fuel
spillage in the event of an accident.
 Use only a genuine Lexus fuel tank cap for
replacement. It is designed to regulate fuel tank
pressure.

EXTERIOR EQUIPMENT
95
MOON ROOF
15X016e
 1Open 2Close
To slide open the moon roof, push the “SLIDE” switch on
the rear side. The moon roof will open and stop partway
30 mm (1.2 in.) from the fully opened position. When you
push the switch again, the moon roof will open fully. To
stop partway, push the same switch or push the “TILT”
switch while the moon roof is moving.
As driving with the moon roof opened fully will cause wind
throbs, we recommend you to drive with the moon roof partway
30 mm (1.2 in.) from the fully opened position.
To operate the moon roof, the ignition key must be in the “ON”
position.
The sun shade can be opened or closed manually. However,
if you open the moon roof, the sun shade will be opened with
the moon roof. To close the moon roof, push the switch on the front side.
The moon roof will fully close. To stop partway, push the
same switch or “TILT” switch.
15X017e
 1
Tilt up 2Lower
To tilt up the rear end of the moon roof, push the “TILT”
switch on the “UP” side. The rear end of the moon roof will
tilt up fully. To stop partway, push the same switch or
“SLIDE” switch.
To lower it, push the switch on the opposite side of the
“UP” side. The rear end of the moon roof will fully close.
To stop partway, push the same switch or “SLIDE” switch.
Retained accessory power: Even if the ignition key is turned
to the “ACC” or “LOCK” position with all the doors closed, t\
he
moon roof can be operated until either of the front doors is
opened (or for about 45 seconds).