2006 LEXUS LX470 sat

AUDIO
229
(c) Listening to the satellite radio
21x511a
Push the “AM·SAT” button to choose a SAT station.
Besides “AM”, “SAT1”, “SAT2” or “SAT3” appears on the
display.
22x651
Turn this knob to select the next or previous channel.

AUDIO
230(d) Presetting a channel
22x652
1. Tune in the desired channel.
2. Push one of the channel selector buttons ( 16 ) and
hold it until a beep is heard. This sets the channel to the
button and the button number ( 16 ) appears on the
display.
Each button can store three SAT channels. To change the
preset channel to a different one, follow the same procedure.
The preset channel memory is
cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (e) Selecting a channel
Tune in the desired channel using one of the following
methods.
22x653a
Preset tuning: Push the button ( 1−6 ) for the channel you
want. The button number ( 1−
6 ) and channel number appear
on the display.
Manual tuning within the channel category: Turn the
“AUDIO−TUNE” knob. The radio will step up or down the
channel.
Manual tuning within the current channel category: Push
the “SEEK” button. The radio will step up or down the channel
within the current channel category.

AUDIO
233
(h) If the satellite radio tuner malfunctions
When
problems occur with the XM tuner, a message will appear on the display. Referring to the table below to identify the problem,
take the suggested corrective action.
ANTENNA
The XM antenna is not connected. Check whether the XM antenna cable is \
attached securely.
A short−circuit occurs in the antenna or the surrounding antenna cable. See a L\
exus certified
dealer.
UPDATING
You have not subscribed to the XM satellite radio. The radio is being up\
dated with the latest
encryption code. Contact the XM satellite radio for subscription inform\
ation. When a contact is
canceled, you can choose the “CH000” and all free −to− air channels.
The premium channel you selected is not authorized. Wait for about 2 seconds until the radio
returns to the previous channel or “CH001”. If it does not change\
automatically, select another
channel. If you want to listen to the premium channel, contact the XM s\
atellite radio.
NO SIGNALThe XM signal is too weak at the current location. Wait until your vehicle reaches a location
with a stronger signal.
LOADINGThe unit is acquiring audio or program information. Wait until the unit has received the informa-
tion.
OFF AIRThe channel you selected is not broadcasting any programming. Select an\
other channel.
−−−−−There is no song/program title or artist name/feature associated with th\
e channel at that time.
No action needed.
−−−
The channel you selected is no longer available. Wait for about 2 seconds until the radio re-
turns to the previous channel or “CH001”. If it does not change a\
utomatically, select another
channel.
The XM Listener Care Center is also available on the phone, please call \
(800) 852 −9696 during the following hours:
Monday – Saturday: 7 a.m. – 1 a.m. Sunday: 12 p.m – 12 a.m.

AUDIO
234
NOTICE
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
Information to user
Alternation or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
NOTICE
This XM tuner supports “Audio Services” (Music and
Talk) of only XM satellite radio and “Text Information”*
linked to the respective audio services.
*Text Information includes, Channel Name, (Artist)
Name, (Song) Title and Category Name.

AUDIO
244(a) When the radio mode is selected
”
“ or
”“switch: Push this switch for seek tuning or to
select a station.
 To select a preset station, push the switch briefly. Do this
again to select the next preset station.
 To seek a station, push and hold the switch until you hear
a beep. Do this again to find the next station. If you push
the switch on either side of the
”
“or
”“ during the
seek mode, seeking will be cancelled.
 To step up or down the frequency, push and hold the switch
even after you hear a beep. When you release from the
switch, the radio will begin seeking up or down for a station.
Do this again to find the next station.
XM satellite radio*—
To select a preset channel, push the
”
“or
”“ side of the
switch. Repeat until a desired channel is found.
*: Use of satellite radio requires XM tuner and service. Contact
your Lexus dealer for details.
(b) When the “TAPE” mode is selected
”
“ or
”“switch: Push this switch to fast forward or
rewind the tape or for automatic program selection.
 Push this switch until you hear a beep to fast forward or
rewind the tape. To stop fast forwarding or rewinding, push
the same side on the switch until you hear a beep.
 Push this switch briefly for automatic program selection.
When automatically selecting a program, you can skip up to
9 programs at a time. See page 237 for details. (c) When the “CD” or “DVD” mode is selected
”
“ or
”“switch:
Use this switch to select a desired
track or CD.
 Push this switch briefly to select a desired track.
 To select a desired CD, push and hold this switch until the
desired number of the CD appears and you hear a beep.
CAUTION
Operate the switches with due care while you are
driving to avoid accidents.

AUDIO
246(d) When the “CD” or “DVD” mode is selected
“
DISC”
Use this button to search a desired CD.
“
TRACK” button: Use this button to search a desired
track or push this button and hold it to fast forward or reverse.
(e) Some basics
This system cannot be used if the audio system is not turned
on.
You cannot select “AM” or “FM” mode in the rear seat if the
“FM” or “AM” mode is used on the front seats side.
If you select the same mode as the front seats side, operating
the controller will affect the mode on the front seats side.
Vehicles with navigation system only:
 When the XM satellite radio* is selected in the front seat, the
“CD” or “DVD” mode cannot be selected in the rear seat.
 When the “CD” or “DVD” mode is selected in the rear seat,
selecting the XM satellite radio* in the front seat will
automatically change the “CD” or “DVD” to “AM” mode in the
rear seat.
CAUTION
This system is not designed for a driver. So, the driver
should not use this system while driving.
Audio system operating hints
NOTICE
To ensure correct audio system operations:
 Be careful not to spill beverages over the audio
system.
 Do not put anything other than a cassette tape or CDs
into the cassette tape slot or CD slot.
 The use of a cellular phone inside or near the vehicle
may cause a noise from the speakers of the audio
system which you are listening to. However, this
does not indicate a malfunction.

STARTING AND DRIVING
295
BRAKE SYSTEM
This brake system has 2 independent hydraulic circuits. If
either circuit should fail, the other will still work. However, the
pedal will be harder to press, and your stopping distance will
increase. Also, the brake system warning light may come on.
CAUTION
Do not drive your vehicle with only a single brake
system. Have your brakes fixed immediately.
Brake booster
The brake booster uses brake fluid pressurized by the pump
to power−assist the brakes. If the brake booster fails during
driving, the brake system warning light comes on and buzzer
sounds continuously. In this case, the brakes may not work
properly. If they do not work well, depress the brake pedal
firmly. If the brake system warning light comes on, immediately
stop your vehicle and contact your Lexus dealer.
The brake system warning light may stay on for about 60
seconds after the ignition key is turned to the “ON” position.
It is normal if the light turns off after a while.
Depressing the brake pedal repeatedly may turn on the brake
system warning light and buzzer. It is normal if the light goes
out and the buzzer stops sounding after a few seconds. You may hear a small sound in the engine compartment after
the engine is started or the brake pedal is depressed
repeatedly. This is a pump pulsating sound of the brake
system, and it is not a malfunction.
CAUTION

Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your brake fluid
pressure reserve.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will increase.
Antilock brake system
The antilock brake system is designed to automatically
help prevent lockup of the wheels during a sudden brake
or braking on slippery roa d surfaces. This assists in
providing directional stability and steering performance
of the vehicle under these circumstances.
Effective way to press the ABS brake pedal: When the
anti−lock brake system function is in action, you may feel the
brake pedal pulsating and hear a noise. In this situation, to
let the anti−lock brake system work for you, just hold the
brake pedal down more firmly. Do not pump the brake in a
panic stop. This will result in reduced braking performance.

STARTING AND DRIVING
296The anti
−lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of approximately
10 km/h (6 mph). It stops operating when the vehicle
decelerates to a speed below approximately 5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces such as
on a manhole cover, a steel plate at a construction site, joints
in a bridge, etc. on a rainy day tends to activate the anti −lock
brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is started or
just after the vehicle begins to move. This means that the
anti−lock brake system is in the self− check mode, and does not
indicate a malfunction.
When the antilock brake system is activated, the
following conditions may occur. They do not indicate a
malfunction of the system:
 You may hear the anti− lock brake system operating and feel
the brake pedal pulsating and the vibrations of the vehicle
body and steering wheel. You may also hear the motor
sound in the engine compartment even after the vehicle is
stopped.
 At the end of the anti−lock brake system activation, the
brake pedal may move a little to the forward.
CAUTION
Do not overestimate the antilock brake system:
Although the antilock brake system assists in
providing vehicle control, it is still important to drive
with all due care and maintain a moderate speed and
safe distance from the vehicle in front of you, because
there are limits to the vehicle stability and effectiveness
of steering wheel operation even with the antilock
brake system on.
If tire grip performance exceeds its capability, or if
hydroplaning occurs during high speed driving in the
rain, the antilock brake system does not provide
vehicle control.
Antilock brake system is not designed to shorten the
stopping distance: Always drive at a moderate speed
and maintain a safe distance from the vehicle in front of
you. Compared with vehicles without an antilock
brake system, your vehicle may require a longer
stopping distance in the following cases:
 Driving on rough, gravel or snowcovered roads.
 Driving with tire chains installed.