2006 LEXUS LX470 change time

222
GAUGES, METERS AND SERVICE REMINDER INDICATORS
63
The following service reminder indicators go off after a few
seconds.

w73

w72a

218
214 wtracorw227
or

The following service reminder indicat
or goes off after about 6
seconds.
The anti −lock brake system warning light, vehicle stability
control system off indicator light and vehicle stability control
system and active traction control system warning light may
stay on for about 60 seconds after the ignition key is turned to
the “ON” position. It is normal if they go out after a while.
If any service reminder indicator or warning buzzer does not
function as described above, have it checked by your Lexus
dealer as soon as possible.
TRIP INFORMATION DISPLAY (Vehicles without navigation system)
13x541z
The following information is shown with the ignition
switch turned on. Each time you push the “MODE” button,
the displayed information is changed.
 Average vehicle speed
 Driving distance after engine starting
 Available driving range
 Average fuel consumption after being refueled
 Current fuel consumption
The displayed trip information values indicate the general
driving condition and may not always reflect precise and actual
conditions.

INTERIOR EQUIPMENT
71
IGNITION SWITCH LIGHT
14X004a
For easy access to the ignition switch, the ignition switch
light comes on when any of the doors are opened.
The light remains on for about 15 seconds and goes out after
all the doors are closed. However, the light goes out
immediately when all the doors are locked or the ignition key
is in the “ACC” or “ON” position.
CLOCK
14X500
The digital clock indicates the time when the ignition key
is at the “ACC” or “ON” position. To reset the hour, press
the “H” button. To reset the minutes, press the “M”
button. To adjust the time to the nearest hour, press the
“:00” button.
For example, if the “:00” button is pressed when the time is
between 9:30 − 9:59 or between 10:01 − 10:29, the time will
change to 10:00.
If the electrical power source has been disconnected from the
clock, the time display will automatically be set to 1:00.
When the headlight switch is in the first or second click stop,
you can also adjust the brightness of the display using the
instrument panel light control dial.

AIR CONDITIONING
207
If manual switching of air intake is desired
20X023a
Each time you push the air intake control button, the mode
changes in order from the RECIRCULATED AIR mode to
AUTOMATIC mode to OUTSIDE AIR mode, then back to the
RECIRCULATED
AIR mode. Each indicator light shows which
mode is now selected.
1 RECIRCULATED mode If quick circulation of cooled air
is desired, select this mode.
2 EXHAUST GAS AUTOMATIC mode If the outside air
contains harmful substances like exhaust gas (i.e., when
the vehicle running just in front of your vehicle accelerates
rapidly), the system changes automatically from the
OUTSIDE AIR mode (with indicators
2
and 3 on) to
the RECIRCULATED mode (with indicators 1
and 2
on).
3 OUTSIDE AIR mode The system will take fresh outside
air into the vehicle. Turning off the air conditioning manually will cancel the
EXHAUST
GAS AUTOMATIC mode. If you select the “AUTO”
mode during fan operating, the air conditioning turns on and
the EXHAUST GAS AUTOMATIC mode will operate.
For normal use, it is best to keep the air intake control button
set to OUTSIDE AIR mode. If recirculated air is used during
heating, the windows will fog up more easily.
In the following cases, the RECIRCULATED mode may
change to the OUTSIDE AIR mode automatically to prevent
interior fog.
 When the outside temperature becomes lower than 4 C
(39 F).
 When the air conditioning compressor malfunctions.
 When the air conditioning cooler refrigerant decreases.
To change the sensitivity of the sensor switching between
the RECIRCULA TED and OUTSIDE AIR in the AUTOMATIC
mode, push the air intake control button until the “AUTO”
indicator light flashes. The display changes as illustrated
below.
The sensitivity of the sensor can be adjusted only while the
vehicle has stopped.

AIR CONDITIONING
208
20X062d
When you turn the “TEMP” knob, the sensitivity changes from
“+3” down to “−3”. If you do not operate any button for a few
seconds or if you push a button other than the air intake control
button and temperature control knob, the previous display
returns.
If manual onoff of the air conditioning is desired
Push the “A/C” button to turn the air conditioning on and push
it again to turn the air conditioning off. If you turn off the air
conditioning manually, the EXHAUST GAS AUTOMATIC
mode will be cancelled.
If the outside temperature is lowered down to around 0 C
(32 F), the air conditioning will turn off automatically. At this
time, the indicator on the A/C button is off and the EXHAUST
GAS AUTOMATIC indicator light remains on. However, the
EXHAUST GAS AUTOMA TIC mode does not operate. When
the air conditioning turns on as with the raised temperature, the
EXHAUST GAS AUTOMATIC mode resumes. If the system is used for ventilation, heating in dry weather or
removing frost or exterior fog on the windshield, turn the air
conditioning off
once it is no longer required. This will improve
fuel economy. The air conditioning can be used for year −round
automatic temperature control including cooling and
dehumidifying operation.
If the air conditioning compressor does not operate, the
indicator of the “A/C” button will blink. If the indicator of the
“A/C” button blinks even when the “A/C” button is pushed
again, have the compressor checked by your nearest Lexus
dealer.

AUDIO
221
21X553
In the “TAPE” or “CD” mode, the applicable functions are
shown in the lowest part of the display. Push the switch
just below to turn on each function.
(b) Tone and balance
How good an audio program sounds to you is largely
determined by the mix of the treble, mid −range, and bass
levels. In fact, different kinds of music and vocal programs
usually sound better with different mixes of treble, mid− range,
and bass.
A good balance of the left and right stereo channels and of the
front and rear sound levels is also important.
Keep in mind that if you are listening to a stereo recording or
broadcast, changing the right/left balance will increase the
volume of one group of sounds while decreasing the volume
of another.
22X612
Each time you push the “AUDIOTUNE” knob, the display
changes as in the following. To adjust the tone and
balance or turn on or off the automatic sound levelizer,
turn the knob.
BAS: Adjusts low− pitched tones.
MID: Adjusts mid− pitched tones.
TRE: Adjusts high− pitched tones.
FAD: Adjusts the sound balance between the front and rear
speakers.
BAL: Adjusts the sound balance between the right and left
speakers.
ASL: Turns on or off the automatic sound levelizer.
Automatic Sound Levelizer (ASL): When the audio sound
becomes difficult to be heard due to road noise, wind noise,
etc. during driving, the system adjusts to the optimum volume
and tone quality according to the noise level. While the
Automatic Sound Levelizer (ASL) is on, “ASL” appears on the
display.

AUDIO
223
(d) Your cassette player
When
you insert a cassette, the exposed tape should be to the
right.
NOTICE
Never try to disassemble or oil any part of the cassette
player. Do not insert anything except a cassette tape
into the slot.
(e) Your CD player with changer
22x647
Your changer can store up to 6 CDs and play selected CDs or
continuously play all the CDs set in the player.
When you set CDs into the player, make sure their labels face
up. If not, the player will display “ERROR1” and the CD
number.
NOTICE
 Never try to disassemble or oil any part of the CD
player. Do not insert anything other than CDs into the
slot.
 Do not insert a CD upon another one, or it will damage
the changer. Insert only one CD into the slot at a time.
The player is intended for use with 12 cm (4.7 in.) CDs only.

AUDIO
225
(b) Presetting a station
21X555
1. Tune in the desired station.
2. Push
one of the station selector buttons ( 16 ) and hold
it until a beep is heard. This sets the station to the button
and the button number ( 16 ) appears on the display.
Each button can store one AM station and two FM stations. To
change the preset station to a different one, follow the same
procedure.
The preset station memory is cancelled when the power
source is interrupted by battery disconnection or a blown fuse. (c) Selecting a station
Tune in the desired station using one of the following methods.
21X556b
Preset
tuning: Push the button ( 1− 6 ) for the station you want.
The button number ( 1− 6 ) and station frequency appear on the
display.
Manual tuning: Turn the “AUDIO− TUNE” knob. The radio will
step up or down to another frequency.
Seek tuning: Push the “SEEK” button. The radio will begin
seeking up or down for a station of the nearest frequency and
will stop on reception. Each time you push the button, the
stations will be searched automatically one after another.

AUDIO
227
Each time you push the
“
” or “” button, the program type
changes as in the following:
 ROCK
 EASY LIS (Easy listening)
 CLS/JAZZ (Classical music and jazz)
 R&B (Rhythm and Blues)
 INFORM (Information)
 RELIGION
 MISC
 ALERT (Emergency message)
Push the “SEEK TRACK” or “SCAN” button with the program
type shown on the display and the radio seeks or scans the
station in the relevant program type.
TRAF (Traffic) function: A station that regularly
broadcasts traffic information is automatically located.
When you push the “TRAF” button, “TRAF SEEK” appears on
the display and the radio will start seeking any traffic program
station.
If no traf fic program station is found, “NO TRAF INFO” appears
on the display for a few seconds and the display returns to the
previous mode. Radio text message:
21x557
If the radio receives a radio text from RDS station, “MSG”
appears on the display. Push the “TEXT” button, and a text
message is displayed.
If the entire the message is not displayed, “
” will appear on
the display. To display the rest of the message, push and hold
the “TEXT” button until you hear a beep.
After the entire message has been displayed, the message will
disappear.
In case a text message is not accepted on the display, you can
push the “TEXT” button and hold it to display the rest of the
message.
When the system can show the station name, “RDS” appears
on the display. Each time you push the “TEXT” button,
indication on the display changes from the band to the station
name, a radio text in this order. After 6 seconds passes,
indication returns to the band.