2006 Lexus GS430 reset

STARTING AND DRIVING
423
4Resetting to a slower speed
Press the c ontrol lever downward in the “– SET” direction and
hold it. Release the lever when the desired speed is attained.
While the lever is held downward, the vehicle speed will
gradually decrease.
When the difference between the actual vehicle speed and the
set speed is less than 5 km/h (3 mph), the set speed can be
lowered 1.6 km/h (1 mph) each time by pressing the control
lever downward in the “– SET” direction quickly within 0.6
seconds.
A quicker way to reset the preset speed is to depress the brake
pedal and then press the control lever downward in the “– SET”
direction.
Even if you downshift the transmission from the “D” or “6” (\
sixth
range) to “5” (fifth range), or from “D” or “5” (f\
ifth range) to “4”
(fourth range) in the conventional cruise control mode, engine
braking will not be applied because this mode is not cancelled.
To slow down, reset the cruise control to a slower speed with
the cruise control lever or depress the brake pedal. If you use
the brake pedal, cruise control is cancelled. 5 Resuming the preset speed
If the preset speed is cancelled by pulling the control lever, by
depressing the brake pedal or vehicle stability control
activation, pushing the lever up in the “+ RES” direction will
restore the speed set prior to cancellation. However, once the
vehicle speed falls below about 40 km/h (25 mph), the preset
speed will not be resumed.
(c) Conventional cruise control mode failure warning
G13075
If the system malfunction is detected when the
conventional cruise control mode is in the ready mode or
operating, the master warning light comes on, a warning
tone sounds and the above message appears.
If this message appears, push the “ON− OFF” button to turn the
system off and then push it again to turn it on. If the setting still
cannot be made or the same message appears again, the
system might have malfunctioned. Although it is no problem
to continue driving, contact your Lexus dealer.

STARTING AND DRIVING
431
VARIABLE GEAR RATIO STEERING SYSTEM (GS430 only)
The variable gear ratio steering system adjusts the wheel
turning angle depending on the vehicle speed and how
much you turn the steering wheel.
The vehicle wheel turning angle will be changed with a smaller
degree of wheel maneuvering when you are driving at very low
speed such as when putting your vehicle into a garage.
When you start or stop the engine, you may hear a small noise
and the steering wheel may move slightly. This is caused when
the system starts or stops, and does not indicate a malfunction.
In the following cases, to prevent the system from overheating,
the system could be temporarily deactivated with the change
in the center position of the steering wheel. This is not a
malfunction. After the cause of the problem is eliminated, the
system will return to normal automatically after a few minutes.
 If you continue maneuvering the steering wheel when the
vehicle is stopped or running at very low speed
 If you continue driving holding the steering wheel to the
extreme right or left
 If you maneuver the steering wheel immediately after
starting the engine at less than about −30C (− 22F) While the system is not functioning, a larger degree of wheel
maneuvering is needed during driving at low speed. If the
center position of the steering wheel is changed frequently,
have your vehicle inspected at your Lexus dealer.CAUTION
Take due care especially when driving at low speed as
the vehicle changes direction in greater proportion to
the steering wheel maneuvering.
NOTICE
Do not disconnect the battery with the steering wheel
turned, or the center position of the steering wheel
could be slightly and temporarily changed. However,
after driving for a short while, the system will return to
normal
and the center position of the steering wheel will
be in the appropriate position.
If you disconnect and reconnect the battery terminal, the
system is reset temporarily. However, it is no problem to drive.
Drive for a short while, the system will be set automatically and
return to normal.

STARTING AND DRIVING
442The tire pressure warning light may turn on due to natural
causes such as natural air l
eaks or tire inflation pressure
changes caused by temperature. In this case, adjusting the
tire inflation pressure will turn off the light after a few minutes.
Pushing the tire pressure warning reset switch should not turn
off the tire pressure warning light. Adjusting the tire inflation
pressure will turn off the light.
The compact spare tire is not equipped with the tire pressure
warning valve and transmitter. If a tire goes flat, the warning
light will not turn off even though the flat tire is replaced with the
spare tire. Replace the spare tire with the repaired tire and
adjust the proper tire inflation pressure. The tire pressure
warning light will turn off after a few minutes.
CAUTION
Each tire, including the spare (if provided), should be
checked m onthly when cold and inflated to the inflation
pressure recommended by the vehicle manufacturer on
the vehicle placard or tire inflation pressure label (tire
and load information label). (If your vehicle has tires of
a different size than the size indicated on the vehicle
placard or tire inflation pressure label (tire and load
information label), you should determine the proper tire
inflation pressure for those tires.)
As an added safety feature, your vehicle has been
equipped with a tire pressure monitoring system
(TPMS–tire pressure warning system) that illuminates a
low tire pressure telltale (tire pressure warning light)
when one or more of your tires is significantly
underinflated. Accordingly, when the low tire pressure
telltale (tire pressure warning light) illuminates, you
should stop and check your tires as soon as possible,
and inflate them to the proper pressure. Driving on a
significantly underinflated tire causes the tire to
overheat and can lead to tire failure. Underinflation
also reduces fuel efficiency and tire tread life, and may
affect the vehicle’s handling and stopping ability.

STARTING AND DRIVING
444If the tire pressure warning light blinks...
G31048
If the tire pressure warning light blinks when the engine
switch “IGON” mode is selected, the tire pressure
warning system is not working properly.
The system will be disabled in the following conditions:
(When the condition becomes normal, the system will work
properly.)

If tires not equipped with tire pressure warning valves and
transmitters are used.
 If the ID code on the tire pressure warning valves and
transmitters is not registered.
 If electronic devices or facilities using similar radio wave
frequencies are nearby.
 If a radio set at similar frequencies is in use in the vehicle. 
If a window tint that affects the radio wave signals is
installed.
 If the tire pressure warning select switch is set to a dif ferent
tire setting.
 If there is a lot of snow or ice on the vehicle, in particular
around the wheels or wheel housings.
 If non− genuine Lexus wheels are used.
 If tire chains are used.
 If the tire inflation pressure is more than 500 kPa (5.1
kgf/cm
2 or bar, 73 psi).
If the tire pressure warning light blinks frequently when the
engine switch “IG −ON” mode is selected, have it checked by
your Lexus dealer.
Even if you use genuine wheels, the tire pressure warning
system may not work properly with some types of tires.
Pushing the tire pressure warning reset switch should not turn
off the tire pressure warning light.

STARTING AND DRIVING
446
Replacing tires and wheels
When replacing the tires and wheels, be sure to install tire
pressure warning valves and transmitters. ID codes on the tire
pressure warning valves and transmitters are registered on the
tire pressure warning ECU. When replacing a tire pressure
warning valve and transmitter, it is necessar y to register the ID
code of tire pressure warning valve and transmitter. Have the
ID code registered by your Lexus dealer.
If the ID code is not registered, the system will not work
properly. After about 1 hour, the tire pressure warning light
blinks to indicate a system malfunction.
NOTICE
When the tires or tire pressure warning valves and
transmitters must be replaced, have them replaced by
your Lexus dealer. The tire pressure warning valves
and transmitters will be affected by the installation or
removal of tires.
Tire pressure warning reset switch
G31004a
When initializing the system, the present tire inflation pressure
is stored as standard. The tire pressure warning system
determines decreased air pressure by comparing the present
and the standard tire inflation pressures. When you change
the set tire inflation pressure, it is necessary to initialize the tire
pressure warning system.
 When rotating the tires on vehicles differing with front and
rear tire inflation pressures.
 When changing the tire inflation pressure by changing
traveling speed or load weight, etc.
 When changing the tire size.

STARTING AND DRIVING
447
To initialize the system, perform the following:
1. Park
the vehicle in a safe place and select the engine switch
in “OFF” mode.
2. Adjust the pressure of all the installed tires to the specified
cold tire inflation pressure level. (See “Tire and wheels” on
pages 542 and 546.)
3. Select the engine switch in “IG −ON” mode.
4. Push and hold the tire pressure warning reset switch until
the tire pressure warning light blinks slowly three times and the
message “PRESSURE INITIAL” appears on the
multi−information display.
5. Wait for a few minutes with the engine switch in “IG −ON”
mode, and then select the engine switch in “OFF” position.
If you push the tire pressure reset switch while the vehicle is
moving, initialization is not performed.
If you push the tire pressure reset switch accidentally and
initialization is performed, adjust the tire inflation pressure to
the specified level and initialize the system again.
G31007
If the tire pressure warning light does not blink slowly three
times and the message “PRESSURE INITIAL” does not
appear on the multi −information display when you push and
hold the reset switch, initialization has failed and the tire
pressure warning system may not work properly. In this case,
initialize the system again. If initialization cannot be
performed, have the system checked at your Lexus dealer.

STARTING AND DRIVING
448
CAUTION
Do not push the reset switch without first adjusting the
tire inflation pressure to the specified level. Otherwise,
the tire pressure warning light may not come on even if
the tire inflation pressure is low, or it may come on when
the tire inflation pressure is actually normal.
Tire pressure warning select switch
G31005a
 1 Main position 22nd position
2 sets of tire pressure warning valve and transmitter ID codes
can be registered.
Once a second set of tires is registered at “2nd”, you can switch
between tire set settings simply by pressing the tire pressure
warning select switch.
There are 2 settings
“MAIN” position: The ID code of the tire pressure warning valve
and transmitter on the tires originally installed on the vehicle is
registered.
“ 2nd ” position: The code is not registered. When you replace
a new set of tires, purchase tire pressure warning valves and
transmitters from your Lexus dealer and have the new ID code
registered by your Lexus dealer.