2006 KIA Optima reset

If the sunroof does not electrically
operate.
1. Remove the retangular plastic lens in
the front of the roof panel.
2. Turn the cross bolt with a phillips
screw driver counterclockwise to
remove the front dome light
assembly.
3. Insert the hexagonal head wrench
provided with the vehicle into the
socket. This wrench can be found in
the glove box.
4. Turn the wrench clockwise to open
or counterclockwise to close.
RESETTING THE SUNROOFWhen your battery happens to be
disconnected or you use the hexagonal
head wrench to operate the sunroof, you
have to reset your sunroof motor as
follows :
• Turn the ignition key to the ON
position.
• Pull the sunroof fuse out from the
main fuse box in engine
compartment and reinstall it.
• Depress the front portion of sunroof
switch and hold it during 5 seconds.
SUNSHADE (IF EQUIPPED)The sunshade can be opened with the
glass panel automatically when the glass
panel is slid. To close the sunshade you
have to do so manually.
MMSA3063
3-67
CAUTION
If you try to open the sunroof when
the temperature is below freezing-
point or when the sunroof is
covered with snow or ice the glass
pane or the sunroof motor could be
damaged.
MS-CNA-Eng 3.QXD 7/25/2005 5:17 PM Page 67

INSTRUMENT CLUSTER
4-19
A/T: Automatic Transaxle
0 1234
5
6
7
8
X1000rpm
PRND
RESET MODE
BRAKE
CRUISE
TRIPAB
ODO
km/h
0 20406080100120
140
160
180
200
220
240
km/hmph
0 20406080
100
120
140
MMSA4059A
Warning and
indicator lights
Tachometer
Engine temperature gauge
Turn signal
indicators
Fuel gauge
Speedometer
Warning and
indicator lights
A/T range indicator(For A/T only)
Odometer/Tripmeter
Tripmeter mode button
Tripmeter reset button
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 19

DRIVING YOUR VEHICLE
4-20GAUGESSPEEDOMETERThe speedometer indicates the forward
speed of the vehicle.ODOMETER/TRIPMETERYou can choose the odometer, tripmeter
A and tripmeter B by pressing the mode
selection button.ODOMETERThe odometer indicates the total distance
the vehicle has been driven.TRIPMETERTRIP A: Tripmeter A
TRIP B: Tripmeter B
The tripmeter indicates the distance of
individual trips selected by the driver.
Tripmeter A and B can be reset to zero
by pressing the reset button for one
second or more, and then releasing.
TACHOMETERThe tachometer indicates the approximate
number of engine revolutions per minute
(rpm).
Use the tachometer to select the correct
shift points and prevent lugging the
engine and/or over-revving it.
The tachometer pointer may move
slightly when the ignition switch is in the
ACC or ON position with the engine
OFF. This movement is normal and will
not affect the accuracy of the tachometer
once the engine is running.
FUEL GAUGEThe fuel gauge indicates the approximate
amount of fuel remaining in the fuel tank.
Fuel tank capacity: 65L (17 us gal.)
The fuel gauge is supplemented by a low
fuel warning light located in the
instrument panel.
MMSA4021
MMSA4022Red Zone
✻
NOTICE
Do not operate the engine within
the tachometer’s RED ZONE. This
may cause severe engine damage.
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 20

4-33
INTERIOR FEATURESDIGITAL CLOCK When the ignition switch is in the ON
position, the clock buttons operate as
follows:
RESET:
To clear away minutes, press the “R”
button with your finger, a pencil or similar
object. When you release the button, the
clock will be set precisely on the hour.For example, if the “R” button is pressed
while the time is between 9:01 and 9:29,
the display will be reset to 9:00.
9:01-9:29 = 9:00
9:30-9:59 = 10:00
HOUR:
Pressing the “H” button with your finger,
a pencil or similar object will advance
the time displayed by one hour.
MINUTE:
Pressing the “M” button with your finger,
a pencil or similar object will advance the
time displayed by one minute.
ELECTRICAL POWER
OUTLET (IF EQUIPPED)To plug in auxiliary electrical equipment,
flip the outlet cover open from the edge
of the cover and follow the proper
installation instructions that are included
with any electrical equipment you install.
Maximum electrical draw must not
exceed 10 ampere at 12 volts after
engine is started.
MMSA4036
✻
NOTICE
• Use when the engine is running,
and remove a plug from the
power outlet after using the elec-
tric appliance. Using when the
engine stops or remaining the
electric appliance with plugged
in for many hours may cause the
battery to be discharged.
• Adjust the air conditioner or
heater to the lowest operation
level when you have to use the
power socket while using air-
conditioner or heater.
(Continued)
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 33

4-37
CRUISE CONTROL
(IF EQUIPPED)The cruise control system provides
automatic speed control for your comfort
when driving on freeways, tollroads, or
other noncongested highways. This
system is designed to function above
approximately 25 mph (40 km/h).
TO SET THE CRUISE1. Push in the cruise control main
switch. This turns the system on.
2. Accelerate to the desired cruising
speed above 25 mph (40 km/h).
3. Push the "COAST/SET" control
switch and release it. The "CRUISE"
indicator light in the instrument
cluster will illuminate after you have
set the vehicle to the desired speed.
4. Remove your foot from the
accelerator pedal and the desired
speed will automatically be
maintained.5. To increase speed, temporarily
depress the accelerator pedal enough
for the vehicle to exceed the preset
speed. When you remove your foot
from the accelerator pedal, the
vehicle will return to the speed you
have set.
TO CANCEL THE CRUISE
SPEEDDo one of the followings:
• Depress the brake pedal.
• Depress the clutch pedal (Manual
transaxle).
• Shift the shift lever to the “N”
position (Automatic transaxle).
• Decrease the vehicle speed 12mph
(20 km/h) lower than memorized
speed.
• Decrease the vehicle speed to less
than approximately 25 mph (40
km/h).
• Release the main switch.
C
R
U
I
S
E
MMSA4013
R
E
S
A
C
C
E
L
C
A
N
C
E
L
C
O
A
S
T
S
E
T
MMSA4014
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 37

DRIVING YOUR VEHICLE
4-38TO RESUME THE PRESET
SPEEDThe vehicle will automatically resume
the speed set prior to cancellation when
you push the control switch "RESUME
(ACCEL)" and release, providing the
vehicle speed is above 25mph(40 km/h).
TO RESET AT A FASTER
SPEED1. Push the control switch "RESUME
(ACCEL)" and hold it.
2. Accelerate to desired speed and
release the control switch. While the
control switch is held, the vehicle
will gradually gain speed.
TO RESET AT A SLOWER
SPEED1. Push the control button “SET
(COAST)” and hold it. While the
control switch is pushed, the vehicle
speed will gradually decrease.
2. When the desired speed is obtained,
release the control button.
R
E
S
A
C
C
E
L
C
A
N
C
E
L
C
O
A
S
T
S
E
T
MMSA4015
R
E
S
A
C
C
E
L
C
A
N
C
E
L
C
O
A
S
T
S
E
T
MMSA4016
MS-CNA-Eng 4(~39).QXD 7/25/2005 5:16 PM Page 38

AUTOMATIC OPERATION
(IF EQUIPPED)The FATC (Full Automatic Temperature
Control) system automatically controls
the heating and cooling. To activate it:
1. Push the "AUTO" switch. The
indicator light will come on
confirming that the Face, Floor and/
or Bi-Level modes as well as the
blower speed and air conditioner will
be controlled automatically.
2. Press the "temperature control"
switch to set the desired temperature.
The temperature will increase to the
maximum 32°C (90°F) by pressing
the red button. Each time the red
button is depressed, the set
temperature will increase by 0.5°C
(1°F).The temperature will decrease to the
minimum 17°C (62°F) by pressing
the blue button. Each time the blue
button is depressed, the set
temperature will decrease by 0.5°C
(1°F).
AMBIENT SWITCHPressing the AMB button displays the
ambient temperature on the LCD.MANUAL OPERATIONThe heating and cooling system can be
controlled manually if the “AUTO”
button is not selected. In the manual
state, the system works sequentially
according to the order of buttons
selected.
System function not manually selected
will be controlled automatically.
Press the "AUTO" button in order to
convert to automatic control of the
system.FAN SPEED CONTROLThe fan speed can be set to the desired
speed by pressing the appropriate fan
speed control button. The higher the fan
speed is, the more air is delivered.
Pressing the "OFF" button turns off the
fan.
DRIVING YOUR VEHICLE
4-48
✻
NOTICE
If the battery has been discharged
or disconnected, the temperature
mode will reset as Centigrade
degree.
This is normal condition and you
can adjust the temperature mode
from Centigrade to Fahrenheit as
follows;
Press the temperature down but-
ton 3 seconds or more with the
AMB button held down. The dis-
play shows that the unit of tem-
perature is adjusted to Centigrade
or Fahrenheit.
MS-CNA-Eng 4(40~).QXD 7/25/2005 5:15 PM Page 48