2006 KIA Optima maintenance

MAINTENANCE
7-40ALUMINUM WHEEL
MAINTENANCEThe aluminum wheels are coated with a
clear protective finish.
• Do not use any abrasive cleaner,
polishing compound, solvent, or wire
brushes on aluminum wheels. They
may scratch or damage the finish.
• Use only a mild soap or neutral
detergent, and rinse thoroughly with
water. Also, be sure to clean the
wheels after driving on salted roads.
This helps prevent corrosion.
• Avoid washing the wheels with high-
speed car wash brushes.
INTERIOR CAREINTERIOR GENERAL
PRECAUTIONSPrevent caustic solutions such as
perfume and cosmetic oil from
contacting the dashboard; they may
cause damage or discoloration. If they do
contact the dashboard, wipe them off
immediately.UPHOLSTERY AND
INTERIOR TRIM CLEANINGVINYLFirst, remove dust and loose dirt from
vinyl with a whisk broom or vacuum
cleaner. Then, clean vinyl surfaces with a
vinyl cleaner.
FABRICFirst, remove dust and loose dirt from
fabric with a whisk broom or vacuum
cleaner. Then, clean with a mild soap
solution recommended for upholstery or
carpets. Remove fresh spots immediately
with a fabric spot cleaner. If a fresh spot
do not receive immediate attention, the
fabric may be stained and its color can be
affected. Also, its fire-resistant properties
may be reduced if the material is not
properly maintained.
CAUTION
After washing the vehicle, test the
brakes while driving slowly to see if
they have been affected by water.
CAUTION
Using anything but recommended
cleaners and procedures may affect
the fabric’s appearance and fire-
resistant properties.
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 40

MAINTENANCE
7-42HEADLIGHT AIMING
ADJUSTMENTBefore performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and
press the front bumper & rear
bumper down several times.
3. See that the vehicle is unloaded
(except for full levels of coolant,
engine oil and fuel, and spare tire, jack,
and tools). Have the driver sit in the
driver’s seat or use equivalent weight.4. Clean the headlight lenses and turn
on the headlight (Low beam).
5. Open the hood.
6. Draw a vertical line (through the
center of each headlight) and the
horizontal line (through the center of
each headlight) on the aiming screen.
1) Horizontal line dimension from
ground: 628 mm (24.72 in)
2) Distance between each vertical
line : 1,306 mm (49.17 in)
And then, draw a parallel line at 30
mm (1.18 in) place under the
horizontal line.
7. Adjust each cut-off line of the low
beam to the parallel line with a
Phillips screwdriver.
ADJUSTMENT AFTER
HEADLIGHT ASSEMBLY
REPLACEMENTIf the vehicle has had front body repair
and the headlight assembly has been
replaced, the headlight aiming should be
checked using the aiming screen as
shown in the illustration. Turn on the
headlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of
light is parallel to center line of the
body and is aligned with point “P”
shown in the illustration.
MMSA7032
Vertical
aiming
HH W
P
MMSA7033
Horizontal line
21 mm (0.82 in)
Cut-off line
Ground line Vertical line
MS-CNA-Eng 7.QXD 7/25/2005 5:09 PM Page 42

INDEX
9-2M
aintenance Schedule ...............................................................7-3
Maintenance Services ...................................................................7-2
Manual Transaxle ..........................................................................4-6
Mirrors ........................................................................................3-58
O
verheating ................................................................................6-2
Overloading .................................................................................5-11
Owner Maintenance ......................................................................7-8
P
arking Brake ...........................................................................7-18
Power Steering ...................................................................4-18, 7-18
R
ear Window Defroster ...........................................................4-32
Road Warning ...............................................................................6-2
Safety Belts ...............................................................................3-22
Seats ............................................................................................3-14
Special Driving Conditions ...........................................................5-7
Specifications ................................................................................8-2
Starting the Engine ........................................................................4-4
Steering Wheel ............................................................................3-58
Suggestions for Economical Operation.........................................5-5
Sunglass Holder ..........................................................................3-64
Sunroof ........................................................................................3-65T
heft-alarm system .....................................................................3-5
Tilt Steering.................................................................................4-18Tires and Wheels .........................................................................7-25
Towing ........................................................................................6-14
Traction control system ...............................................................4-40
Trailer Towing ............................................................................5-11
Trunk Lid ....................................................................................3-52
V
ehicle Break-In Process ...........................................................1-3
W
arnings and Indicators..........................................................4-21
Windows .....................................................................................3-11
Windshield Defrosting and Defogging (Automatic type) ...........4-56
Windshield Defrosting and Defogging (Manual Type) ..............4-54
Wiper Blades ...............................................................................7-22
Wipers and Washers....................................................................4-30
Ms-CNA-Eng-INDEX.qxd 7/25/2005 5:07 PM Page 2