2006 JEEP LIBERTY radio

garage door opener’s Owner’s Manual. Finally, repro-
gram the hand-held transmitter(s) to HomeLink using
the steps under Programming HomeLink .
Gate Operator/Canadian Programming
Canadian radio-frequency laws require transmitter sig-
nals to time-out (or quit) after several seconds of
transmission - which may not be long enough for
HomeLink to pick up the signal during programming.
Similar to this Canadian law, some U.S. gate operators are
designed to time-outin the same manner.
If you live in Canada or you are having difficulties
programming a gate operator by using the Program-
ming HomeLink procedures (regardless of where you
live), replace step two with the following:
NOTE: If programming a garage door opener or gate
operator, it is advised to unplug the device during the
 cycling process to prevent possible overheating. Press and hold the HomeLink button while you press
and release - every two seconds (
cycle) your hand-held
transmitter button until the radio signal has success-
fully been accepted by HomeLink. (The message
TRAINED will appear on the HomeLink display.)
Proceed with the remaining steps under Programming
HomeLink to complete.
Using HomeLink
To operate, simply press and release the programmed
HomeLink button. Activation will now occur for the
trained device (i.e. garage door opener, gate operator,
security system, entry door lock, home/office lighting,
etc.). For convenience, the hand-held transmitter of the
device may also be used at any time. In the event that
there are still programming difficulties or questions,
contact HomeLink at: www.homelink.comor1-800-355-
3515 .
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS

Instrument Panel And Interior Controls .......170

Instrument Cluster ......................171
▫ 3.7L Engines .........................171
▫ 2.8L Diesel Engines ....................172

Instrument Cluster Description .............173

Electronic Digital Clock ..................183
▫ Clock Setting Procedur e.................183

Radio General Information ................183
▫ Radio Broadcast Signals .................183 ▫
Two Types Of Signals ..................183
▫ Electrical Disturbances ..................184
▫ AM Reception .......................184
▫ FM Reception ........................184

Sales Code RBK—AM/ FM Stereo Radio With CD
Player And CD Changer Controls ...........185
▫ Radio Operation ......................185
▫ CD Player Operation ...................1874

▫CD Changer Control Capability —
If Equipped .........................189

Sales Code RBQ—AM/FM Stereo Radio With
6 - Disc CD Changer ....................191
▫ Radio Operation ......................191
▫ CD Player Operation ...................194

Sales Code RB1—AM/FM Stereo Radio With
DVD/GPS Navigation System ..............199

6–Disc Remote CD Changer — If Equipped ....199
▫ Loading The CD Changer ...............199

Satellite Radio — If Equipped ..............201
▫ System Activation .....................201
▫ Electronic Serial Number/Sirius Identification
Number (ENS/SID) ....................201 ▫
Selecting Satellite Mode In RBB, RAH And
RBK Radios .........................202
▫ Selecting Satellite Mode In RBP, RBU, RAZ,
RB1 And RBQ Radios ..................202
▫ Selecting a Channel ....................203
▫ Storing And Selecting Pre-Set Channels ......203
▫ Using The PTY (Program Type) Button
(If Equipped) ........................203
▫ PTY Button Scan.....................203
▫ PTY Button Seek.....................204
▫ Satellite Antenna ......................204
▫ Reception Quality .....................204

Remote Sound System Controls — If Equipped . . 205
▫ Radio Operation ......................206
168 UNDERSTANDING YOUR INSTRUMENT PANEL

▫Tape Player .........................206
▫ CD Player — Single Disc In Radio .........206
▫ CD Player — 6 Disc In Cargo Area .........206

CD/DVD Disc Maintenance ...............207

Radio Operation And Cellular Phones ........207

Climate Controls .......................208
▫ Blower Control .......................208
▫ Temperature Control ...................208
▫ Mode Selection .......................208
▫ Operating Tips .......................210
UNDERSTANDING YOUR INSTRUMENT PANEL 169
4

ELECTRONIC DIGITAL CLOCK
The clock and radio each use the display panel built into
the radio. A digital readout shows the time in hours and
minutes whenever the ignition switch is in the ON or
ACC position and the time button is pressed.
When the ignition switch is in the OFF position, or when
the radio frequency is being displayed, time keeping is
accurately maintained.
Clock Setting Procedure
1. Turn the ignition switch to the ON or ACC position
and press the time button. Using the tip of a ballpoint pen
or similar object, press either the hour (H) or minute (M)
buttons on the radio.
2. Press the H button to set hours or the M button to set
minutes. The time setting will increase each time you
press a button.
RADIO GENERAL INFORMATION
Radio Broadcast Signals
Your new radio will provide excellent reception under
most operating conditions. Like any system, however, car
radios have performance limitations, due to mobile op-
eration and natural phenomena, which might lead you to
believe your sound system is malfunctioning. To help
you understand and save you concern about these “ap-
parent” malfunctions, you must understand a point or
two about the transmission and reception of radio sig-
nals.
Two Types of Signals
There are two basic types of radio signals... AM or
Amplitude Modulation, in which the transmitted sound
causes the amplitude, or height, of the radio waves to
vary... and FM or Frequency Modulation, in which the
frequency of the wave is varied to carry the sound.
UNDERSTANDING YOUR INSTRUMENT PANEL 183
4

Electrical Disturbances
Radio waves may pick up electrical disturbances during
transmission. They mainly affect the wave amplitude,
and thus remain a part of the AM reception. They
interfere very little with the frequency variations that
carry the FM signal.
AM Reception
AM sound is based on wave amplitude, so AM reception
can be disrupted by such things as lightning, power lines
and neon signs.
FM Reception
Because FM transmission is based on frequency varia-
tions, interference that consists of amplitude variations
can be filtered out, leaving the reception relatively clear,
which is the major feature of FM radio.
NOTE: On vehicles so equipped the radio, steering
wheel radio controls and 6 disc CD/DVD changer will
remain active for up to 45 seconds after the ignition
switch has been turned off. Opening a vehicle front door
will cancel this feature.
184 UNDERSTANDING YOUR INSTRUMENT PANEL

SALES CODE RBK—AM/ FM STEREO RADIO
WITH CD PLAYER AND CD CHANGER
CONTROLS
NOTE: The radio sales code is located on the lower left
side of your radio faceplate.
Radio Operation
Power/Volume Control
Press the ON/VOL control to turn the radio on. Turn the
volume control clockwise to increase the volume.
NOTE: Power to operate the radio is supplied through
the ignition switch. It must be in the ON or ACC position
to operate the radio.
Seek
Press and release the SEEK button to search for the next
station in either the AM or FM mode. Press the top of the
button to seek up or the bottom to seek down. The radio
will remain tuned to the new station until you make
another selection. Holding the button in will bypass
stations without stopping until you release it.
Tune
Press the TUNE control up or down to increase or
decrease the frequency. If you press and hold the button,RBK Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 185
4

the radio will continue to tune until you release the
button. The frequency will be displayed and continu-
ously updated while the button is pressed.
To Set The Radio Push-Button Memory
When you are receiving a station that you wish to
commit to push-button memory, press the SET button.
SET 1 will show in the display window. Select the “1–5”
button you wish to lock onto this station and press and
release that button. If a button is not selected within 5
seconds after pressing the SET button, the station will
continue to play but will not be locked into push-button
memory.
You may add a second station to each push-button by
repeating the above procedure with this exception: Press
the SET button twice and SET 2 will show in the display
window. Each button can be set for SET 1 and SET 2 in
both AM and FM. This allows a total of 10 AM and 10 FM
stations to be locked into push-button memory. The stations stored in SET 2 memory can be selected by
pressing the push-button twice. Every time a preset
button is used a corresponding button number will be
displayed.Audio
The audio button controls the BASS, TREBLE, BAL-
ANCE, and FADE.
Press the AUDIO button and BASS will be displayed.
Press the SEEK + or SEEK – to increase or decrease the
Bass tones.
Press the AUDIO button a second time and TREB will be
displayed. Press the SEEK + or SEEK – to increase or
decrease the Treble tones.
Press the AUDIO button a third time and BAL will be
displayed. Press the SEEK + or SEEK – to adjust the
sound level from the right or left side speakers.
186 UNDERSTANDING YOUR INSTRUMENT PANEL