2006 INFINITI QX56 diagram

DI-46
WARNING CHIME
Revision: November 20092006 QX56
Wiring Diagram — CHIME —EKS00BCR
WKWA3627E

DI-50
WARNING CHIME
Revision: November 20092006 QX56
Preliminary CheckEKS00BCV
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSE AND FUSIBLE LINK
Check for blown BCM fuse or fusible link.
Refer to DI-46, "Wiring Diagram — CHIME —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to PG-
4, "POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect BCM connectors M18 and M20.
2. Check voltage between BCM harness connector terminals and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between BCM and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between BCM harness connector M20 terminal 67 and ground.
OK or NG
OK >> Inspection End.
NG >> Repair harness or connector.
Unit Power source Fuse or fusible link No.
BCM Battery
f
Ignition switch ON or START 59
TerminalsIgnition switch position
(+) (– )O FFO N
Connector Terminal
M20 70
GroundBattery volt-
age Battery volt-
age
M18 38 0VBattery volt-
age
WKIA2072E
Continuity should exist.
LIIA0915E

WARNING CHIMEDI-55
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
3. CHECK FRONT DOOR SWITCH LH
Check continuity between front door switch LH terminal 2 and
exposed metal of switch while pressing and releasing switch.
OK or NG
OK >> Replace the BCM. Refer to BCS-20, "BCM" .
NG >> Replace the front door switch LH.
Key Warning Chime Does Not OperateEKS00BCZ
1. CHECK FUSE
Check if the key switch fuse [No. 19, located in the fuse block (J/B)] is blown. Refer to DI-46, "
Wiring Diagram
— CHIME —" .
Is the fuse blown?
YES >> Replace the fuse. Be sure to repair the cause of malfunction before installing new fuse.
NO >> GO TO 2.
2. CHECK WARNING CHIME OPERATION
With key removed from the ignition key cylinder and the front door LH open, turn the lighting switch to 1st or
2nd position.
Does warning chime sound?
YES >> GO TO 3.
NO >> Go to DI-53, "
All Warning Chimes Do Not Operate" or DI-54, "Key Warning Chime and Light
Warning Chime Do Not Operate (Seat Belt Warning Chime Does Operate)" .
When front door switch
LH is released
: Continuity should exist.
When front door switch
LH is pressed : Continuity should not
exist.
WKIA2023E

REAR SONAR SYSTEMDI-63
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
Wiring Diagram — SONAR —EKS00BD4
WKWA4087E

DI-68
REAR SONAR SYSTEM
Revision: November 20092006 QX56
Preliminary CheckEKS00BD9
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
1. CHECK FUSE
Check for blown rear sonar system fuse.
Refer to DI-63, "
Wiring Diagram — SONAR —" .
OK or NG
OK >> GO TO 2.
NG >> If fuse is blown, be sure to eliminate cause of problem before installing new fuse. Refer to PG-4,
"POWER SUPPLY ROUTING CIRCUIT" .
2. CHECK POWER SUPPLY CIRCUIT
1. Disconnect sonar control unit connector.
2. Check voltage between sonar control unit connector B56 termi- nal 8 and ground.
OK or NG
OK >> GO TO 3.
NG >> Check harness for open between sonar control unit and fuse.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between sonar control unit B56 terminal 6 and ground.
OK or NG
OK >> Inspection End.
NG >> Check harness ground circuit.
Unit Power Source Fuse
Sonar control unit ON or START 12
TerminalsIgnition switch position
(+) (-) ON or START
Connector Terminal
B56 8 Ground Battery voltage
WKIA1145E
Terminals
Continuity
(+)
(– )
Connector Terminal
B56 6 Ground Yes
WKIA1146E

CLOCKDI-71
C
DE
F
G H
I
J
L
M A
B
DI
Revision: November 2009 2006 QX56
CLOCKPFP:25820
Wiring Diagram — CLOCK —EKS00BDD
WKWA1178E

DI-76
REAR VIEW MONITOR
Revision: November 20092006 QX56
Wiring Diagram — R/VIEW —EKS00BDI
WKWA1180E

EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
DE
F
G H
I
J
K L
M
SECTION
A
EC
Revision: November 2009 2006 QX56
INDEX FOR DTC ...................................................
..... 8
DTC No. Index .................................................... ..... 8
Alphabetical Index ............................................... ... 12
PRECAUTIONS ..................................................... ... 16
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 16
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 16
Precaution ........................................................... ... 16
PREPARATION ...................................................... ... 20
Special Service Tools .......................................... ... 20
Commercial Service Tools ................................... ... 22
ENGINE CONTROL SYSTEM ............................... ... 23
System Diagram .................................................. ... 23
Multiport Fuel Injection (MFI) System ................. ... 24
Electronic Ignition (EI) System ............................ ... 26
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 27
AIR CONDITIONING CUT CONTROL .................. ... 28
Input/Output Signal Chart .................................... ... 28
System Description ............................................. ... 28
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 29
System Description ............................................. ... 29
Component Description ....................................... ... 30
CAN COMMUNICATION ....................................... ... 31
System Description ............................................. ... 31
EVAPORATIVE EMISSION SYSTEM .................... ... 32
Description .......................................................... ... 32
Component Inspection ........................................ ... 35
Removal and Installation ..................................... ... 36
How to Detect Fuel Vapor Leakage .................... ... 37
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 39
System Description ............................................. ... 39
Diagnostic Procedure .......................................... ... 40
Component Inspection ........................................ ... 43
POSITIVE CRANKCASE VENTILATION .............. ... 45
Description .......................................................... ... 45
Component Inspection ........................................ ... 45IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) .....................................................................
... 47
Description ........................................................... ... 47
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 48
Introduction .......................................................... ... 48
Two Trip Detection Logic ..................................... ... 48
Emission-related Diagnostic Information ............. ... 49
Malfunction Indicator Lamp (MIL) ........................ ... 63
OBD System Operation Chart ............................. ... 65
BASIC SERVICE PROCEDURE ............................ ... 71
Basic Inspection ..................................................... 71
Idle Speed and Ignition Timing Check ................. ... 76
VIN Registration ..................................................... 77
Accelerator Pedal Released Position Learning ... ... 78
Throttle Valve Closed Position Learning .............. ... 78
Idle Air Volume Learning ..................................... ... 78
Fuel Pressure Check .............................................. 80
TROUBLE DIAGNOSIS ......................................... ... 83
Trouble Diagnosis Introduction ............................ ... 83
DTC Inspection Priority Chart .............................. ... 89
Fail-safe Chart ..................................................... ... 91
Symptom Matrix Chart ......................................... ... 92
Engine Control Component Parts Location ......... ... 96
Vacuum Hose Drawing ........................................ .102
Circuit Diagram .................................................... .103
ECM Harness Connector Terminal Layout .......... .105
ECM Terminals and Reference Value .................. .105
CONSULT-II Function (ENGINE) ......................... .114
Generic Scan Tool (GST) Function ...................... .127
CONSULT-II Reference Value in Data Monitor .... .129
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .132
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .134
Description ........................................................... .134
Testing Condition ................................................. .134
Inspection Procedure ........................................... .134
Diagnostic Procedure .......................................... .135
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .144