TF-32
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
Inspections Before Trouble DiagnosisEDS002HH
TRANSFER FLUID CHECK
Check fluid for leaks and fluid level. Refer to TF-11, "Inspection" .
PREPARATION FOR ROAD TEST
The purpose of the test is to determine overall performance of
transfer and analyze causes of problems.
When a malfunction is found in any part of transfer, perform the
road test to locate the malfunction area and repair the malfunc-
tion parts.
The road test consists of the following three parts.
–Check before engine is started. Refer to TF-32, "CHECK
BEFORE ENGINE IS STARTED" .
–Check at idle. Refer to TF-32, "CHECK AT IDLE" .
–Cruise test. Refer to TF-33, "CRUISE TEST" .
CHECK BEFORE ENGINE IS STARTED
1. CHECK 4WD SHIFT INDICATOR LAMP
1. Park vehicle on flat surface.
2. Turn ignition switch to “OFF ” position.
3. Move A/T selector lever to “P ” position.
4. Set 4WD shift switch to “2WD” position.
5. Turn ignition switch to “ON ” position. (Do not start engine.)
Does 4WD shift indicator lamp turn ON for approximately 1 second?
YES >> GO TO 2.
NO >> Go to TF-117, "
4WD Shift Indicator Lamp and 4LO Indicator Lamp Do Not Turn ON" .
2. CHECK 4WD WARNING LAMP
1. Turn ignition switch to “OFF ” position.
2. Move A/T selector lever to “P ” position.
3. Set 4WD shift switch to “2WD” position.
4. Turn ignition switch to “ON ” position. (Do not start engine.)
Does 4WD warning lamp turn ON?
YES >> GO TO TF-32, "CHECK AT IDLE" .
NO >> GO TO TF-121, "
4WD Warning Lamp Does Not Turn ON" .
CHECK AT IDLE
1. CHECK 4WD SHIFT INDICATOR LAMP
1. Park vehicle on flat surface and engage the parking brake.
2. Turn ignition switch to “OFF ” position.
3. Move A/T selector lever to “P ” position.
4. Set 4WD shift switch to “2WD” position.
5. Start engine.
Does 4WD shift indicator lamp turn ON?
YES >> GO TO 3.
NO >> GO TO 2.
SMT089D
TF-42
TROUBLE DIAGNOSIS
Revision: November 20092006 QX56
30 SB Shut off relayIgnition switch: ON
0V
Ignition switch: OFF Battery voltage
31 G Transfer fluid temperature
sensor Ignition switch: ONTransfer fluid temperature approx. 20°C
(68
°F) 1.1V
Transfer fluid temperature approx. 80°C
(176 °F) 0.3V
33 R/L Transfer shift high relay
monitor
Vehicle stopped
Engine running
A/T selector lever
“
N ” position
Brake pedal
depressed 4WD shift switch: 4H to 4LO (
“Wait ” func-
tion is operating.) Battery voltage
Except the above 0V
34 BR Clutch pressure switch
Vehicle stopped
Engine running
A/T selector lever
“ D ” position 4WD shift switch: AUTO or 4H (
“Wait ”
function is not operating.) 0V
Vehicle stopped
Engine running4WD shift switch: 2WD (
“Wait ” function is
not operating.) Battery voltage
35 BR/
W Line pressure switch
Ignition switch: ON
A/T selector lever “
D” position
4WD shift switch: AUTO 0V
After the vehicle
has been left at
room temperature
for 5 minutes and
more with ignition
switch in “
OFF”
position.
Ignition switch: ON
A/T selector lever: “P ” or "N" position
4WD shift switch: other than AUTO Battery voltage
40 L ATP switch
Vehicle stopped
Engine running
A/T selector lever
“ N ”
Brake pedal
depressed 4WD shift switch: 4H to 4LO or 4LO to 4H
(While actuator motor is operating.)
0V
Except the above Battery voltage
41 R Transfer motor relay moni-
tor
Accelerator pedal
depressed
Vehicle stopped
Engine running
Brake pedal
depressed 4WD shift switch: 2WD 0V
4WD shift switch: AUTO or 4LO (A/T
selector lever
“P ” or “ N” position) 0V
(Battery volt-
age for approx.
2 sec. after
shifting to
“P ”
and “N ”.)
4WD shift switch: AUTO or 4LO (Except
for A/T selector lever “P ” or “N ” position) Battery voltage
4WD shift switch: 4H (A/T selector lever
“ P ” position) 0V
(Battery volt-
age for approx.
2 sec. after
shifting to
“P ”.)
4WD shift switch: 4H (Except for A/T
selector lever “P ” position) Battery voltage
Te r m i n a l
Wire
color Item
ConditionData (Approx.)
