2006 INFINITI FX35 removal

REAR WIPER AND WASHER SYSTEM WW-51
C
D E
F
G H
I
J
L
M A
B
WW
Revision: 2006 December 2006 FX35/FX45
Removal and Installation of Rear Wiper Arm, Adjustment of Wiper Arms Stop
Location
NKS0033G
REMOVAL
1. Operate wiper motor, and stop it at the auto stop position.
2. Remove cover wiper arm.
3. Remove wiper arm nut, and remove wiper arm from vehicle.
INSTALLATION
1. Prior to wiper arm installation, turn on wiper switch to operate wiper motor and then turn it “OFF” (auto stop).
2. Lift the blade up and then set it down onto glass surface to set the blade center to clearance “L” immediately before tightening
nut.
3. Eject washer fluid. Turn on wiper switch to operate wiper motor and then turn it “OFF”.
4. Ensure that wiper blades stop within clearance “L”.

Tighten wiper arm nuts to specified torque.
5. Installation is the reverse order of removal.
Removal and Installation of Rear Wiper Motor NKS0033H
Clearance “L” : 45 – 60 mm (1.77 - 2.36 in)
Rear wiper arm nut : 5.0 N·m (0.51 kg-m, 44 in-lb)
PKIB3565E
1. Rear wiper motor 2. Screw 3. Wiper blade
4. Wiper arm 5. Cover wiper arm 6. Nut
7. Pivot cap 8. Nut 9. Washer
10. Cushion rubber
SKIB7578E

WW-52
REAR WIPER AND WASHER SYSTEM
Revision: 2006 December 2006 FX35/FX45
REMOVAL
1. Remove wiper arm. Refer to WW-51, "REMOVAL" .
2. Remove pivot cap, and remove nut and nozzle or tube from vehicle.
3. Remove back door finisher. Refer to EI-46, "
BACK DOOR
TRIM" .
4. Disconnect rear wiper motor connector.
5. Remove rear wiper motor mounting bolts and remove rear wiper motor.
CAUTION:
Never remove cushion rubber.
INSTALLATION
1. Clean up the pivot area as illustrated. This will reduce possibility of wiper arm looseness.
2. Attach pivot cap.
3. Install rear wiper motor to the vehicle.
4. Connect rear wiper motor connector. Turn rear wiper switch ON to operate rear wiper motor, then turn wiper switch OFF (auto
stop).
5. Install back door finisher. Refer to EI-46, "
BACK DOOR TRIM" .
6. Attach wiper arm.
CAUTION:
Never drop the wiper motor or cause it to contact other parts.
Removal and Installation of Rear Wiper BladeNKS0033I
REMOVAL
1. Remove wiper arm. Refer to WW-51, "REMOVAL" .
2. Turn wiper blade 90 degrees against wiper arm, and pull it out downward for removal.
CAUTION:
Replace wiper blade as wiper blade assembly.
INSTALLATION
Installation is the reverse order of removal.
PKIB3588E
Rear wiper motor
mounting bolt : 5.9 N·m (0.59 kg-m, 51 in-lb)
SEL024J
SKIA6169E

REAR WIPER AND WASHER SYSTEM WW-53
C
D E
F
G H
I
J
L
M A
B
WW
Revision: 2006 December 2006 FX35/FX45
Washer Nozzle AdjustmentNKS0033J
Adjust washer nozzle with suitable tool as shown in the figure.
Unit: mm (in)
Removal and Installation of Washer NozzleNKS0033K
REMOVAL
1. Remove high-mounted stop lamp. Refer to LT- 1 3 0 , "High-
Mounted Stop Lamp" .
2. Remove screw and remove washer nozzle from high-mounted stop lamp.
INSTALLATION
Installation is the reverse order of removal.
Spray position h (height) (width) φ
S
A, B 2.5 (0.098) 80 (3.15) 30 (1.18)
Adjustable range : ±15 ° (In any direction)
SKIA5088E
SKIA5087E
PKIB6132E

WW-54
REAR WIPER AND WASHER SYSTEM
Revision: 2006 December 2006 FX35/FX45
Washer Tube LayoutNKS0033L
Check ValveNKS0033M
A check valve is provided in the washer fluid line. Be careful not to
connect check valve to washer tube in the wrong direction.
Removal and Installation of Rear Wiper and Washer SwitchNKS0033N
Refer to WW-37, "Removal and Installation of Front Wiper and Washer Switch" .
Removal and Installation of Washer TankNKS0033O
Refer to WW-37, "Removal and Installation of Washer Tank" .
Removal and Installation of Washer pumpNKS0033P
Refer to WW-38, "Removal and Installation of Washer Pump" .
PKIC9709E
SEL411H

WW-56
POWER SOCKET
Revision: 2006 December 2006 FX35/FX45
Removal and Installation of Front Power Socket – 1NKS003N8
REMOVAL
1. Remove A/T console finisher. Refer to IP-10, "INSTRUMENT
PANEL ASSEMBLY" .
2. Remove instrument clock finisher. Refer to IP-10, "
INSTRU-
MENT PANEL ASSEMBLY" .
3. Disconnect power socket connector.
4. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
5. Remove ring from ashtry while pressing pawls.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Front Power Socket – 2NKS0033U
REMOVAL
1. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
2. Remove ring from power socket finisher while pressing pawls.
3. Disconnect power socket connector.
INSTALLATION
Installation is the reverse order of removal.
Removal and Installation of Rear Power SocketNKS004F1
REMOVAL
1. Remove console rear finisher. Refer to IP-17, "CENTER CON-
SOLE" .
2. Disconnect power socket connector.
3. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
4. Remove ring from power socket finisher while pressing pawls.
INSTALLATION
Installation is the reverse order of removal.
PKIC9710E
SKIA5096E
SKIA5094E

POWER SOCKET WW-57
C
D E
F
G H
I
J
L
M A
B
WW
Revision: 2006 December 2006 FX35/FX45
Removal and Installation of Luggage Room Power SocketNKS0033V
REMOVAL
1. Remove inner socket from the ring. While pressing the hook on the ring out from square hole.
2. Remove ring from power socket finisher while pressing pawls.
3. Disconnect power socket connector.
INSTALLATION
Installation is the reverse order of removal.
SKIA5097E

HORN
WW-59
C
D E
F
G H
I
J
L
M A
B
WW
Revision: 2006 December 2006 FX35/FX45
Removal and InstallationNKS0033X
REMOVAL
1. Remove front grille. Refer to EI-22, "FRONT GRILLE" .
2. Disconnect all horn connectors.
3. Remove horn mounting bolt and remove horn from vehicle.
INSTALLATION
Installation is the reverse order of removal.

Tighten horn bolt to specified torque.
SKIA5093E
Horn mounting bolt : 5.8 N·m (0.59 kg-m, 51 in-lb)