Page 97 of 277
1
FEATURES OF YOUR HYUNDAI
83
!
B600A01A-AAT (If installed) B610B01A-GAT(Without Airbag)
To Adjust the Steering Wheel:
1. Push the lever downward to unlock.
2. Raise or lower the steering wheel to the desired position.
3. After adjustment, securely tighten
the lever by pulling it upward.
WARNING:
Do not attempt to adjust the steer-ing wheel while driving as this may result in loss of control of the ve- hicle which may cause serious in-jury or death. Press the center hub of the steering wheel to sound the horn.
B610B01E
HXDFL600
STEERING WHEEL TILT LEVER
HORN
!
!
CAUTION:
To prevent damage to the goods or the vehicle, care should be takenwhen carrying fragile or bulky ob- jects in the trunk.
WARNING:
Avoid eye injury. DO NOT overstretch the luggage net. ALWAYS keep your face and body out of its recoil path. DO NOT use when the strap hasvisible signs of wear or damage.
Page 98 of 277
1FEATURES OF YOUR HYUNDAI
84CRUISE CONTROL
B660A01S-GAT (If installed) B660B01E-GATTo Set the Cruise Speed
The cruise control system provides automatic speed control for your com- fort when driving on freeways, tollroads, or other noncongested highways. Thisis designed to function above approxi- mately 40 km/h (25 mph). 1. Push in the cruise control main
switch on the end of the barrel. The"CRUISE" indicator light in the in- strument cluster will be illuminated.This turns the system on.
2. Accelerate to the desired cruising
speed above 40 km/h (25 mph).
3. Push the control switch downward to "SET (COAST)" and release it.
4. Remove your foot from the accel- erator pedal and the desired speed will automatically be maintained.
B660A01E
B660B01E
Main Switch
B610A01S-GAT (With Airbag) Press the pad on the steering wheel to sound the horn. B610A01E
Page 99 of 277

1
FEATURES OF YOUR HYUNDAI
85
!
B660C03E-AAT To Cancel the Cruise Speed B660D01E-AATTo Resume the Preset Speed
To disengage the cruise control sys- tem, pull the control switch toward the steering wheel to the "CANCEL" posi-
tion. Additionally, the following actionswill disengage the system:
o Depress the brake pedal.
o Depress the clutch pedal (Manual transaxle).
o Shift the selector lever to "P" or "N" position (Automatic transaxle).
o Decrease the vehicle speed to less
than 40 km/h (25 mph).
o Release the main switch. The vehicle will automatically resumethe speed set prior to cancellation when you push the control switch upward to the "RESUME (ACCEL)" position andrelease it, providing the vehicle speed is above 40 km/h (25 mph).
B660C01E
B660D01E
5. To increase speed, depress the ac-
celerator pedal enough for the ve- hicle to exceed the preset speed. When you remove your foot from the accelerator pedal, the vehicle willreturn to the speed you have set.
WARNING:
To avoid accidental cruise control engagement, keep the cruise control main switch off when not using thecruise control.
B660E01E-AAT To Reset at a Faster Speed
1. Push the control switch upward tothe "RESUME (ACCEL)" position and hold it.
2. Accelerate to desired speed and release the control switch. Whilethe control switch is held, the ve-hicle will gradually gain speed.
Page 100 of 277

1FEATURES OF YOUR HYUNDAI
86
!
1. Push the control switch downward
to "SET (COAST)" and hold it. The vehicle will decelerate.
2. When the desired speed is obtained, release the control switch. Whilethe control switch is pushed, the vehicle speed will gradually de-crease. WARNING:
o Keep the main switch off when not using the cruise control.
o Use the cruise control system
only when traveling on open high-ways in good weather.
o Do not use the cruise control
when it may not be safe to keepthe car at a constant speed, for instance, driving in heavy or vary- ing traffic, or on slippery (rainy,icy or snow-covered) or winding roads or over 6% up-hill or down- hill roads.
o Pay particular attention to the driving conditions whenever us-ing the cruise control system.
o During cruise-control driving with a manual transaxle vehicle,do not shift into neutral withoutdepressing the clutch pedal, or the engine will be overrevved. If this happens, depress the clutchpedal or release the main switch. o With the cruise control engaged,
when the brake pedal is applied,it is normal to hear the cruisecontrol system deactivate. This is an indication of normal system operation.
o During normal cruise control operation, when the "SET(COAST)" is activated or reacti-vated after applying the brakes, the cruise control will energize after approximately 3 seconds.This delay is normal.
B660F02E-AAT To Reset at a Slower Speed
B660B01E
Page 101 of 277
1
FEATURES OF YOUR HYUNDAI
87HEATING AND COOLING CONTROL
B710A01E-GAT
(If Installed)
1. Side Defrost Nozzle
2. Side Ventilator
3. Windshield Defrost Nozzle
4. Center Ventilator B710B01S-AAT CENTER VENTILATOR The center ventilators are located in the middle of the dashboard. The di-rection of air flow from the vents in the center of the dashboard is adjustable. To control the direction of the air flow,move the knob in the center of the vent up-and-down and side-to-side. B710C02HP-AAT SIDE VENTILATOR The side ventilators are located on each side of the dashboard. To changethe direction of the air flow, move the knob in the center of the vent up-and- down and side-to-side. The vents areopened when the vent knob is moved to " " position. The vents are closed when the vent knob is moved to " ".Keep these vents clear of any obstruc- tions.
B710A02E
Page 102 of 277
1FEATURES OF YOUR HYUNDAI
88
B670A01A-AAT Rotary type (If installed) This model has four controls for the heating and cooling system. They are:
1. Air flow control
2. Air intake control
3. Temperature control
4. Fan speed control HXDOM046
B670D01E
B670D01E-AAT Air Flow Control This is used to direct the flow of air. Air can be directed to the floor, dashboardoutlets, or windshield. Five symbols are used to represent Face, Bi-Level, Floor, Floor-Defrost and Defrost airposition.
Face-Level
Selecting the "Face" mode will causeair to be discharged through the face level vents. HXDFL539
HEATING AND VENTILATION
1
2
3
4
Page 103 of 277
1
FEATURES OF YOUR HYUNDAI
89
HXDFL541
Bi-Level
Air is discharged through the face vents and the floor vents. Floor-Level
Air is discharged through the floorvents, windshield defroster nozzle, side defroster nozzle and side ventilator. Floor-Defrost Level
Air is discharged through the wind- shield defrost nozzle and the floorvents, side defroster nozzle, side ven- tilator. If the "Floor-Defrost" mode is selected,the A/C will turn on automatically and "Fresh" mode will be activated. HXDFL543HXDFL540
Page 104 of 277

1FEATURES OF YOUR HYUNDAI
90
With the "Fresh" mode selected, air enters the vehicle from the outside andis heated or cooled according to the function selected. With the "Recirculation" mode selected, air from within the passenger compart- ment will be drawn through the heatingsystem and heated or cooled accord- ing to the function selected. NOTE:
o It should be noted that prolonged
operation of the heating in "Re- circulation" mode ( ) will give rise to fogging of the windshieldand side windows and the air within the passenger compart- ment will become stale. In addi-tion, prolonged use of the air conditioning with the "Recircu- lation" mode ( ) selected mayresult in the air within the pas- senger compartment becoming excessively dry.
o When the ignition switch is turned "ON" the air intake con-trol will change to "Fresh" mode( ) in floor, floor-defrost and defrost position. This is normal operation.
Defrost-Level
Air is discharged through the wind-shield defroster nozzle, side defroster nozzle and side ventilator. If the "Defrost" mode is selected, theA/C will turn on automatically and "Fresh" mode will be activated to im- prove windshield defrosting. HXDFL542B670C02E-AAT Air Intake Control This is used to select fresh outside air or recirculating inside air. To change the air intake control mode,(Fresh mode, Recirculation mode) push the control button. FRESH MODE
( ) : The indicator
light on the button goes off when the air intake control is fresh mode. RECIRCULATION MODE ( ): The
indicator light on the button is illumi- nated when the air intake control is recirculation mode. B670C01E