2006 HONDA ELEMENT bulb

This indicator comes on when you
turn the ignition switch to the ON
(II) position with the headlight
switch of f and the parking brake set.
It should go of f if you turn on the
headlights or release the parking
brake. If it comes on at any other
time, it means there is a problem
withtheDRL.Theremayalsobea
problem with the high beam
headlights.This indicator comes on with the
high beam headlights. For more
inf ormation, see page .
This indicator comes on as a
reminder that you must ref uel soon.
The lef t or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicators do not blink
or they blink rapidly, it usually
means one of the turn signal bulbs is
burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
Whenyouturnonthehazard
warning button, both turn signal
indicators blink. All turn signals on
the outside of the vehicle should
flash. On Canadian models, this indicator
comes on with reduced brightness
when the daytime running lights
(DRL) are on (see page ).
When the indicator comes on, there
is about 1.6 U.S. gal (6
)of fuel
remaining in the tank bef ore the
needle reaches E. There is a small
reserve of f uel remaining in the tank
when the needle does reach E.
This indicator comes on when you
set the cruise control. See page
f or inf ormation on operating the
cruise control.
180
62
62
120
Canadian models only
If equippedTurn Signal and Hazard Warning
Indicators ‘‘Daytime Running
Lights’’ Indicator
High Beam Indicator
Low Fuel Indicator
Cruise Control Indicator
Instrument Panel Indicators
56

Theheadlightswereproperlyaimed
when your vehicle was new. If you
regularly carry heavy items in the
cargo area or pull a trailer,
readjustment may be required.
Adjustmentsshouldbedonebyyour
dealer or other qualif ied mechanic.Open the hood.
If you need to change the
headlight bulb on the driver’s side,
remove the f ront end of the air
intake duct by pulling it out.
Your vehicle has halogen headlight
bulbs. Handle it by its steel base and
protect the glass f rom contact with
your skin or hard objects. If you
touch the glass, clean it with
denaturedalcoholandacleancloth.
1.
CONT INUED
Headlight A iming Replacing a Headlight Bulb
Lights
Maint enance
179
AIR INTAKE DUCT
Halogen headlight bulbs get very hot
when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Remove the electrical connector
f rom the bulb by pulling the
connector straight back.
Remove the rubber weather seal
by pulling on the tab.
Unclip the end of the hold-down
wire f rom its slot. Pivot it out of
the way, and remove the bulb.Insert the new bulb into the hole,
making sure the tabs are in their
slots. Pivot the hold-down wire
back in place, and clip the end into
the slot.
Reinstall the rubber weather seal.
Make sure it is right side up; it is
marked ‘‘TOP.’’
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Push the electrical connector onto
the new bulb.
(Driver’s side)
Install the f ront end of the air
intake duct.
The f ront parking/turn signal light
is next to the headlight bulb. On
the driver’s side, remove the f ront
end of the air intake duct by
pulling it out (see page ).
1.
2.
3.
4. 5.
6.
7.
8.
2.179
Replacing a Front Parking/Turn
Signal Light Bulb
Lights
180

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place.
Testthelightstomakesurethe
new bulb is working.
(Driver’s side)
Install the f ront end of the air
intake duct.Place a cloth between the trim of
the lens and the body, at the top of
the lens. Remove the front side
marker light assembly by caref ully
prying on the trim of the lens with
a small f lat-tip screwdriver.Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
1.
3.
4.
5.
2.
3.
6.
CONT INUED
Replacing a Front Side Marker
Light Bulb
Lights
Maint enance
181
SCREWDRIVER
CLOTH LIGHT
ASSEMBLY LIGHT ASSEMBLY
SOCKET

Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Turn on the lights to make sure
the new bulb is working.
Put the light assembly back into
the body, bottom first. Push on the
top edge until it snaps into place.Open the hatch and the tailgate.
Remove the two mounting screws
with a Phillips-head screwdriver,
and remove the taillight assembly
f rom the body by pulling it back.Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Determine which of the three
bulbs is burned out: brake/
taillight, turn signal light or back-
up light.
1.
4.
5.
2.3.
4.
6.
Replacing Rear Bulbs
Lights
182
TAILLIGHT ASSEMBLY
SCREW
SCREW
SOCKET
SOCKET
SOCKET

Reinstall the socket into the light
assembly by turning it clockwise
until it locks.Place a cloth and insert a small
f lat-tip screwdriver between the
lef t edge of the lens and the
housing. The lens will come down.
Testthelightstomakesurethe
new bulb is working.
When reinstalling the taillight
assembly, f irst place the two pins
in the holes in place. Tighten the
two mounting bolts.
Pull the bulb straight out of its
socket. Push the new bulb in until
it bottoms in the socket.Turn on the parking lights and
check that the new bulb is
working.
Put the lens back into the light
assembly, right side f irst. Push on
the lef t edge until it snaps into
place.
1.
2.
6.
7.
3.
4.
5.
Lights
Replacing a Rear License Plate
Bulb
Maint enance
183
SCREWDRIVER
CLOTH
HOUSING
LENS
LENSBULB

Open the hatch. Remove the light
assembly cover by pushing in on
the tabs on both sides and pulling
the cover down.
Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.Testthelightstomakesurethe
new bulb is working.
Put the socket back into the light
assembly, and turn it clockwise to
lock it in place.
Put the cover back onto the light
assembly. Push it on until it locks
in place.
1.
2. 3.4.
5.
6.
Lights
Replacing a High-mount Brake
Light Bulb
184
COVER
TAB
TAB
BULB
SOCKET

CONT INUED
BatteryCharging System ...........................
Indicator .54,209
............................
Jump Starting .205
..............................
Maintenance .193
............................
Specif ications .223
..............................
Bef ore Driving .123
..................................
Belts, Seat .10,20
...........................
Beverage Holders .87...................................
Body Panels .178
..................................
Booster Seats .45
Brakes ...........
Anti-lock System (ABS) .149
.............
Break-in, New Linings .124
....................
Bulb Replacement .182
...........................................
Fluid .177
.........................................
Parking .83
.................
System Indicator . 54,211
........................
Wear Indicators .149
.............................
Braking System .148
.................
Break-in, New Vehicle . 124
..
Brightness Control, Instruments . 63
........................
Brights, Headlights .62
Bulb Replacement ..........................
Back-up Lights .182
..............................
Brake Lights .182
................
Front Parking Lights . 180
........
Front Side Marker Lights . 181
.................................
Headlights .179
............................
Specif ications .223
....................
Turn Signal Lights . 180
..............................
Bulbs, Halogen .179
................................
Bungee Cords .135
....................................
Accessories .130
ACCESSORY (Ignition Key .......................................
Position) .69
..............
Accessory Power Sockets . 87
....................
Additives, Engine Oil . 171
.............................
Airbag (SRS) .11, 23
...
Airbags, Additional Information . 23
...
Additional Safety Precautions . 29
.............................
Airbag Service .28
How the Side Airbag Of f ......................
Indicator Works .28
..
How the SRS Indicator Works . 27
How Your Front Airbags .........................................
Work .24
...
How Your Side Airbags Work . 26
........................
SRS Components .23
................
Air Conditioning System . 91
............................................
Usage .91
.......................
Air Pressure, Tires .188
.........................
Normal Driving .188
......................................
Antif reeze .173
Anti-lock Brakes (ABS) ...............................
Indicator .55, 150
...................................
Operation .149 ..............
Anti-thef t, Audio System . 116
.
Anti-thef t Steering Column Lock . 69
......................
Armrests, Front Seat .74
..................................
Audio System .94
...
Automatic Seat Belt Tensioners . 21
.............
Automatic Speed Control . 120
..............
Automatic Transmission . 143
..........................
Capacity, Fluid .222
...............
Checking Fluid Level . 175
.......................................
Shif ting .143
.
Shif t Lever Position Indicator . 143
................
Shif t Lever Positions . 143
....................
Shif t Lock Release . 146
......................
Auxiliary Input Jack .112
Index
A
B
INDEX
I