2006 HONDA ACCORD COUPE ignition

This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. If it comes on at any other
time, there is a problem with the
ABS. If this happens, have your
vehicle checked at a dealer. With
this indicator on, your vehicle still
has normal braking ability but no
anti-lock function. For more
info rmation, see page . This
indicator comes on for a few
seconds when you turn the ignition
switch to the ON (II) position. It will
then go off if you have inserted a
properly-coded ignition key. If it is
not a properly-coded key, the
indicator will blink, and the engine
will not start (see page ).
This indicator also blinks several
times when you turn the ignition
switch from the ON (II) position to
the ACCESSORY (I) or the LOCK
(0) position. The
left or right turn signal indicator
blinks when you signal a lane change
or turn. If the indicator does not
blink or blinks rapidly, it usually
means one of the turn signal bulbs is burned out (see page ). Replace
the bulb as soon as possible, since
other drivers cannot see that you are
signaling.
When you press the hazard warning
button, both turn signal indicators
blink. All turn signals on the outside
of the vehicle should f lash.
75
249
209
Anti-lock Brake System
(A BS) Indicator
Immobilizer System
Indicator Turn Signal and
Hazard Warning
Indicators
Instrument Panel Indicators
Inst rument s and Cont rols
59
——y

y
(%yy

This indicator is located in the fuel
gauge. It comes on as a reminder
that you must refuel soon.
When the indicator comes on, there
are about 2.72 U.S. gal (10.3
)of
fuel remaining in the tank before the
needle reaches E. There is a small
reserve of fuel remaining in the tank
when the needle does reach E.
This indicator reminds you that the
exterior lights are on. It comes on
when the light switch is in either the
or position. If you turn the
ignition switch to the ACCESSORY
(I) or LOCK (0) position without
turning off the light switch, this
indicator will stay on. A reminder
chime will also sound when you open
the driver’s door.
This indicator c omes on when the
washer fluid level is low. Add washer
fluid when you see this indicator (see page ).
If this indicator comes on when the
ignition switch is turned to the ON
(II) position and the parking brake is
released, it means there is a problem
in the high beam headlight’s circuit.
Have your vehicle c
hecked by your
dealer.
When the daytime running lights
(DRL) are on, this indicator comes
on with reduced brightness (see
page ).
This
indicator comes on with the
high beam headlights. For more
info rmation, see p age .69
70 238
Canadian models only
Instrument Panel Indicators
‘‘Daytime Running
Lights’’ Indicator Low Fuel Indicator
Lights On Indicator
Washer Level Indicator
High Beam Indicator
60
LOW FUEL INDICATOR
——y

y
(%yy

This indicator comes on when the
security system is set. For more info rmation, see p age .
The specific door indicator comes on
in this monitor if either door is not
fully closed.
The trunk indicator comes on when
the trunk is opened or if it is not fully
closed.
All the indicators in the monitor
come on for a few seconds when you
turn the ignition switch to the ON
(II) position.
If the remaining engine oil life is
more than 16 percent, this indicator
comes on for a few seconds when
you turn the ignition switch to the
ON (II) position.
This indicator reminds you that it is
time to take your vehicle in for
scheduled maintenance. The
maintenance
main items and sub
items will be displayed in the
information display. See page for
more inf ormation on the
maintenance minder.
This indicator goes of f when your
dealer resets it after completing the
required maintenance service. 174
221 Security System Indicator
Maintenance Minder
Indicator Door and T runk Open Monitor
Instrument Panel Indicators
Inst rument s and Cont rols
61
SECURITY SYSTEM INDICATOR
——y
y
(%yy

On all V6 models On all V6 models
This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position.
Ifitcomesonandstaysonatany
other time, or if it does not come on
when you turn the ignition switch to
the ON (II) position, there is a
problem with the VSA system. Take
your vehicle to a dealer to have it
checked. Without VSA, your vehicle
still has normal driving ability, but
will not have VSA traction and
stability enhancement. See pagefor more information on the
VSA system. This indicator c
omes on when you
turn on the cruise control system by
pressing the CRUISE button (see page ).
This indicator c omes on when you
set the cruise control. See page for information on operating the
cruise control.
This indicator h
as three functions:
Itcomesonasareminderthatyou
have turned off the vehicle
stability assist (VSA) system.
It flashes w hen VSA is active (see
page ).
It comes on along with the VSA
system indicator if there is a
problem with the VSA system.
This indicator normally comes on for
a few seconds when you turn the
ignition switch to the ON (II)
position. For more information, see page .
1.
2.
3.
211 211
211 175
175
Instrument Panel Indicators
Vehicle Stability Assist
(VSA ) System Indicator Cruise Main Indicator
Cruise Control Indicator
VSA A ctivation Indicator
62
——y
y
(%yy

To switch the information display
between the odometer/trip meter,
outside temperature/trip meter (if
equipped), and engine oil lif e and
maintenance item code(s), press the
Select/Reset knob repeatedly.
This shows the total distance your
vehicle has been driven. It measures
miles in U.S. models and kilometers
in Canadian models.
It is illegal under U.S. f ederal law and
Canadian provincial regulations to
disconnect, reset, or alter the
odometer with the intent to change
the number of miles or kilometers
indicated. When you turn the ignition switch to
the ON (II) position, your last
selection appears in the display.
Gauges
Odometer
Inst rument s and Cont rols
63
TACHOMETERSPEEDOMETER
FUEL GAUGE
SELECT/RESET
KNOB TEMPERATURE
GAUGE
INFORMATION DISPLAY
U.S. A/T model is shown. ODOMETER/TRIP METER/OUTSIDE
TEMPERATURE INDICATOR/CHECK FUEL CAP
INDICATOR/MAINTENANCE MINDER
——y
y
(%yy

This shows how much fuel you have.
It may show slightly more or less
than the actual amount. The needle
returns to the bottom after you turn
off the ignition. This
shows the temperature of the
engine’s coolant. During normal
operation, the pointer should rise
from the bottom white mark to about
the middle of the gauge. In severe
driving conditions, such as very hot
weather or a long period of uphill
driving, the pointer may rise into the
upperhalfofthegauge.Ifitreaches
the red (Hot) mark, pull safely to the side of the road. See page for
instructions and precautions on
checking the engine’s cooling
system.
This meter shows the number of
miles (U.S.) or kilometers (Canada)
driven since you last reset it.
There are two trip meters: Trip A
and Trip B. Switch between them by
pressing the Select/Reset knob
repeatedly. Each trip meter works
independently, so you can keep track
of two dif f erent distances.
To reset a trip meter, display it and
then press and hold the select/reset
knob until the number resets to ‘‘0.0’’.
274
Fuel Gauge T emperature Gauge
Trip Meter
Gauges
64
Avoid driving with an extremely low
f uel level. Running out of f uel could
cause the engine to misf ire, damaging
the catalytic converter.
——y
y
(%yy

µ
µ
µ
Turning the
switch to the ‘‘ ’’ position turns
on the parking lights, taillights, side-
marker lights, and rear license plate
lights. Push
down on the
lever to signal a left turn and up to
signal a right turn. To signal a lane
change, push lightly on the lever,
and hold it. The lever will return to
center when you release it or
complete a turn.
Tu rn signal
Off
Parking and interior lights
Headlights
High beams
Flashhighbeams Turning
the switch to the ‘‘ ’’
position turns on the headlights. If
you leave the lights on with the
key removed from the ignition
switch, you will hear a reminder
chime when you open the driver’s
door.
Push the lever
f orward until you hear a click to turn
on the high beams. The blue high
beam indicator will come on (see page ). Pull the lever back to
return to the low beams.
To f lash the high beams, pull the
lever back lightly, then release it.
The high beams will stay on as long
as you hold the lever back.
When the light switch is in the
‘‘ ’’ or ‘‘ ’’ position, the
lights on indicator comes on as a
reminder. This indicator stays on if
you leave the light switch on and
turn the ignition switch to the
ACCESSORY (I) or LOCK (0)
position.
1.
2.
3.
4.
5.
6.
60
Headlights On Turn Signal
High Beams
Turn Signal and Headlights
Inst rument s and Cont rols
69
——y
y
(%yy

The lights will turn on again when
you unlock or open the driver’s door.
If you remove the key f rom the
ignition switch with the headlight
switch on, but do not open the
door and get out, the lights will
turn of f af ter 10 minutes. If you unlock the door, but do not
open it within 15 seconds, the lights
will go off. With the driver’s door
open, the lights on indicator comes
on along with a lights-on reminder
chime.
This f eature turns of f the headlights,
parking lights, side marker lights,
taillights, and license plate lights
automatically under these
conditions:
If you leave the headlight switch in
the or position, remove
the key, then open and close the
driver’s door, the lights will turn
of f af ter 15 seconds. With the headlight switch OFF or
position, the high beam
headlights and the high beam
indicator come on with reduced
brightness when you turn the
ignition switch to the ON (II)
position and release the parking
brake. They remain on until you turn
the ignition switch of f , even if you
set the parking brake.
The headlights revert to normal
operation when you turn them on
with the switch.
Automatic Lighting Of f Feature
Daytime Running Lights
Headlights
70
——y
y
(%yy