2006 GREAT WALL SAFE wheel

SA-17
Ball stud
Inspection on Ball Stud
1. Check the lower ball stud to see whether it is excessively
loose or not.
(a) Prop up the front of the vehicle with jack and then support
it with the bracket.
(b) Tread down the brake pedal after verifying that the front
wheel are in straight line.
(c) Move the arm vertically to check the lower ball stud to see
whether the clearance is overlarge.
Max vertical clearance : 0.5mm
2. Check the upper ball stud to see whether it is over-loose.
Move the wheel vertically to check whether the clearance of
the ball stud is over large.
3. Check the rotating performance of ball stud
(a) Take apart the ball stud.
(b) Shake the ball stud several times forward and backward
before mounting on the nut, as shown in the drawing.
(c) Rotate the nut continuously with a torsion meter, which
rotates the nut round per 2 to 4 seconds, and read the
reading of the torsion meter after the fifth round.
Fastening torque (running)
Lower ball stud: (0.1-4)N
m
Upper ball stud: (0.1-4)N
m
Disassembly of Ball Stud
1. Tear down the steering knuckle.
(see the SA-14).
2. Take apart the lower ball stud from the lower arm; and
3. Take apart the upper ball stud from the upper arm. Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Ball Stud)

SA-20
(f) Screw up the adjustable nuts so that the protruding length
of the bolt is equal to that before tearing down.
(g) Mount on the wheel and dismantle the bracket, bounce
the vehicle several times so as to make the suspension in
place.
(h) Screw up the adjustable nut to regulate the ground
clearance.
2. Tighten the locking nuts according to the specified torque.
Tighten torque
(83
5)N
m
3. Mount on the dust cover.


Mount of Torsion rod Spring
Notice: the torsion rod spring marked with
L
(left) or

R
(right), do not mount the springs at the incorrect
location.
1. Mount the torsion rod spring, pedestal arm and torsion arm;
(a) Coat the lithium base grease on the spline of torsion rod
spring.
(b) Align the wide-teeth parts and then mount the pedestal
arm on the torsion rod spring.
(c) Align the wide-teeth parts and then mount the torsion arm
on the torsion rod spring.
(d) Mount the torsion rod spring on the side of torsion arm
and mount on the pedestal arm on the adjusting bolts.
(e) Screw up the torsion arm nuts according to the specified
torque.
Fastening torque
(83
)N
m Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Torsion Rod Spring)
front

SA-23
3. Mount the guide lever on the lower arm
Fastening torque
(96
0)N
m
4. Link the transverse stabilizer rod with the lower arm.
Fastening torque
(23
3)N
m
5. Mount the vibration damper.
6. Mount the ending part of the drag rod:
(a) Link the drag rod end to the steering knuckle arm, mount
and screw up the nuts according to the specified torque.
Fastening torque
(91
0)N
m
(b) Lock the nut with the new split pin.
7. Mount the torsion rod spring.
8. Check the Alignment of Front Wheel.
(See the page SA-3)
Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Lower Arm and Vibration Damper)

SA-25
2. Mount the upper arm
(a) Mount on the upper arm and the regulating gasket.
(b) Screw up the bolts according to the specified torque.
Fastening torque
(96
0)N
m
Remark: Mount back the gaskets of the same thickness in the
same number on the original locations.
3. Connect the upper ball stud and upper arm together.
Fastening torque
26N
m
4. Check the Alignment of Front Wheel
(See page SA-3)
Suspension System and Automobile Axle (Dr/2WD)
Front Suspension (Upper Arm)

SA-26Suspension System and Automobile Axle (Dr/ 2WD)
Front Suspension (Guide Lever)
Guide Lever
Disassembly of Guide Lever
1. Mark the assembly mark on the guide lever.
2. Tear down the front fixing nuts from the guide lever.
3. Tear down the guide lever from the lower arm.
Tear down the nuts that fix the guide lever on the lower
swimming arm, and then tear down the guide lever.
Mount of Guide Lever
1. Mount on the front fixing nuts
Mount on the front fixing nuts and meanwhile align the
assembly marks on the guide lever.
4. Screw up the fixing nuts according to the specified torque,
(a) Dismantle the bracket so that make the vehicle bounce
sever times to put the suspension in balance.
(b) Screw up the front fixing nut.
5. Check the Alignment of Front Wheel
(See Page SA-3) 2. Mount the guide lever on the bracket
(a) Mount the washer and liner on the guide lever, and then
mount the guide lever on bracket.
(b) Mount the sleeve ring, the liner and the washer on the
guide lever.
(c) Screw up the fixing nuts with finger.
3. Mount the guide lever on the lower swing arm.
Screw up the fixing nuts according to the specified torque.
Fastening torque
(96
)N
m
assembly mark
assembly mark

SA-28Suspension System and Automobile Axle(SF/2WD)
Front Suspension
locking ring
cushion block nut
locking ringcushion blockupper arm
transverse stabilizer rod
bolt
transverse stabilizer rod gasket

rubber
snubber washer
restrictor tube
Brake
caliper
steering knuckle
brake oil pipe bracket
steering
knuckle arm
brake shell
dust cover

oil seal -front hub
front wheel
bearing(inner)
front wheel hub and
front brake discstop washer
lock plate
front hub bearing
(outer)
steering knuckle nut

liner
lower
ball stud






Parts that cannot be reused after being used:specified torque
N
m
135-155
23
2925
29 70-90
132-152
20-26
180 127-147132
152123
shock absorber


steering knuckle
outer flange cap
Front wheel hub and steering knuckle
Element figures
SF2WD
stabilizer rod gasket

stabilizer rod gasket

rubber snubber
washer
stabilizer rod gasket

stabilizer rod gasket

SA-29
Front Wheel Hub
Disassembly of Front Wheel Hub
1. Tear down the brake caliper.
(a) Tear down the brake Bundy tube from the brake caliper,
and block the Bundy tube line with a cork.
(b) Tear down the brake caliper from the steering knuckle.
2. Tear down the steering knuckle outer flange cap.
3. Tear down the front wheel hub and brake disc.
(a) Open the lock plate with a screwdriver.
(b) Tear down the steering knuckle nut with the SST tools to
take out the. lock plate
(c) Tear down the other steering knuckle nut with SST tools
to take out the stop washer and the steering knuckle outer
bearing.
(d) Tear down the front wheel hub and the brake disc
assembly.
4. Tear down the front hub, oil seal, front hub bearing
(inner) inner race and roller assembly.
(a) Pry out the oil seal.
Notice: the deformed oil seal should not be reused.
(b) Take out the front hub bearing (inner) inner race and
roller assembly.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)

SA-30
5. Front hub bearing outer race inspection and change
(a) Check each bearing
Wash the inner and outer races of each bearing, and check
them whether they are wearied or damaged.
(b) Tear down the outer race of each bearing.
Tap out the bearing outer race with copper bar and
hammer.
Notice: bind the dismantled inner and outer races of
bearing together to prevent from mixing.
6. Front brake disc inspection and change
(a) Check the wear situation of front brake disc.
(b) Tear down the bolts that connect the front wheel hub and
front brake disc.
(c) Connect the front wheel hub and front brake disc and
screw up the bolts with moment spanner to the specified
torque diagonally
Fastening torque
(70-80)N
m
(d) Conduct the dynamic balance test on the dynamic balancer,
the amplitude value displayed should not be above 13.5g
under the condition that the measuring rotating velocity
is 796 r/m and the locking rotating velocity 786 r/m,
otherwise, tap in the counter balanced clip, which is 4g
each, at the corresponding location, the number of the
clip should not be more than 4.
(e) Tap in the new bearing outer race with the special service
tool.
Notice: the inner and outer races of bearing should be
changed in set.
Assembly of Front Wheel Hub
1.Mount on the inner race and roller assembly of front hub
bearing (inner) as well as the front hub oil seal.
Coat the lithium base grease of 4 to 5 mm on the inside surface of
the bearing outer race and front wheel hub, and plaster the
lubricant in the front hub bearing (inner) and the roller assembly.
Coat a little lubricant on the lips of oil seal of front wheel hub, and
then tap the oil seal of front hub in place with special service tool.
Notice: do not coat the lubricant on the front brake disc face.
Suspension System and Automobile Axle (SF/2WD)
Front Wheel Hub and Steering Knuckle (Front Wheel Hub)