2006 GREAT WALL DEER air

CL-2Clutch
Troubleshooting
Troubleshooting
Trouble Causes Repairing approaches
Difficulty in gearshift
or non-gearshiftOverlarge free stroke of clutch pedal
There is air in clutch pipe
Failure of clutch brake-wheel cylinder
Failure of clutch master cylinder
Overlarge clutch pendulum difference due to incorrect mounting, the
friction liner is stained with oil or is breaking
There is dirty or adhesive materials on spline of input shaft or clutch rib
Failure of clutch pressure plateAdjust the free stroke of pedal
Exhaust the air in clutch pipe
Change the clutch brake-wheel cylinder
Change the master cylinder
Check the clutch rib
Repair according to requirement
Change the clutch pressure plate
Disengagement of gear
box or clutch slipAbrasion of clutch guide shaft
Insufficient free stroke of clutch pedal
The friction liner of clutch rib is stained with oil or is worn
Failure of clutch pressure plate
Seize up of separation forkChange the guide shaft
Adjust the free stroke of pedal
Check the clutch rib
Change the clutch pressure plate
Check the separation fork
Clutch seize-up or
shakingThe friction liner of clutch rib is stained with oil or is worn
Failure of clutch pressure plate
Looseness of engine seatCheck the clutch rib
Change the clutch pressure plate
Repair according to requirement
Looseness of clutch
pedalThere is air in clutch pipe
Failure of clutch brake-wheel cylinder
Failure of clutch master cylinderExhaust the air in clutch pipe
Change the clutch brake-wheel cylinder
Change the master cylinder
Over-loud clutch noiseSeize up of separation fork;
Abrasion or stained spot of separation bearing
Abrasion of guide bearing
Parts looseness in clutch pressure plateRepair according to requirement
Change the separation bearing
Change the guide bearing
Change the clutch pressure plate

CL-3Clutch
Inspection and Adjustment of Clutch Pedal, Air Exhausting of Clutch
Air-exhausting of clutch
Remark: in case operation needs to be conducted for the clutch
system or if there is air in clutch, exhaust the air.
Notice : Do not stain the painted surface with brake liquid,
if any brake liquid is left, wash it away immediately.
1.
Fill the brake liquid into the oil cup of clutch master cylinder;
The oil cup of master cylinder shall often be checked and, if
necessary, added with brake liquid.
2.
Connect the ethene resin pipe to the air-exhausting valve.
Insert the other end of the pipe into the container, half of which
is filled with brake liquid.
3. Air-exhausting in clutch system
a) Move the clutch pedal up and down slowly for several times.
b) Loosen the air-exhausting valve when pressing the pedal
increasingly until there is brake liquid overflowing, then
tighten the air-exhausting valve.
c)
Repeat this operation until the bubble in brake liquid disappears.
Inspection on and adjustment
of clutch pedal
1. Check whether the pedal height is correct
Pedal height that begins from front wall board:
Dr SF
(165
5)mm
SL SK SY SJ
(190-200)mm
2. Adjust the pedal height where necessary
Loosen the locking nut and screw off the adjusting bolts until
the pedal height is correct. Then screw up the locking nut.
Pedal free stroke
3. Check whether the pedal free stroke is correct
Press the pedal lightly until the resistance generated by clutch
occurs.
pedal free stroke: (5-15)mm
4. Adjust the pedal free stroke where necessary;
a) Loosen the locking nut and rotate the push-rod until the
stroke is correct;
b) Screw up the locking nuts;
c) Check the pedal height after the adjustment of pedal free
stroke.
adjusting spot in
pedal height
pedal height
pedal free stroke

CL-5Clutch
Clutch Master Cylinder
Disassembly of oil cup of master cylinder
1. Tear down the oil cup
a) Use the pinch and hammer to tap out the spring pin with
groove;
b) Tear down the oil cup and ring pipe.
Assembly of master cylinder
1. Mount the oil cup
a) Mount the oil cup and the new ring pipe.
b) Use the pinch and hammer to tap in the spring pin with
groove.
Mount of master cylinder
1. Mount the master cylinder
Mount the fixing nuts and screw them up.
2. Connect the clutch pipes;
Connect the clutch pipes with SST
3. Connect the push-rod and mount the pin;
Encase the pin of push-rod with clamping pliers.
4. Exhaust the air in clutch system and adjust the clutch
pedal.

CL-6Clutch
Clutch Brake-Wheel Cylinder
Clutch brake-wheel cylinder
Element drawing
clutch brake-wheel cylinder
springpistondust coverpush-rod air-exhausting plug
N*m
specified torque
Disassembly of brake-wheel cylinder
1. Tear down the clutch pipeline.
Remove the pipeline with SST
2. Tear down the two bolts to take down the clutch
brake-wheel cylinder
mount of brake-wheel cylinder
1. Mount the brake-wheel cylinder with two bolts;
2. Connect the clutch pipeline;
Connect the pipeline with SST;
3. Exhaust the air in clutch system.
18
2
19
1

MT-3
Troubleshooting
Gear Box
Troubleshooting
Non-use of clutch
Non-full separation of clutch
Severely warned tooth rings of synchronizing
fittings
Over-hard locating springUse the right driving approach
Checking for adjustment
Change
Change Difficulty in gear engagement
Over-low oil level
Lubricating oil of inferior quality
Non-timely oil change
Unsuitable axial location or clearance of gears
Bearing damage
Burr or collision on gearAdd oil to the specified level
Change it with the specified oil
Change the oil and damaged parts
Check for adjustment
Change
Repair or change the gear
Oil leakage, oil penetration Oil added above the specified level
Loss or missing of bolts
Vent plug trouble
Sealing element damageAdjust oil to the given level
Reassembling or fasten the bolt according to
the specified torque
Change
Change
Damage of synchronizer Overexert in gear shift
Non-use of clutch
Damage on spring collar of synchronizer
Incorrect mounting of drive shaftChange
Use the right driving approach
Change
Check for adjustment
Non-engagement of gear Trouble in controlling mechanism
Incorrect assembling the locating spring or
steel ball
Invalidation of locating spring
Severely worn gear sleeve or fork groove
Seriously worn toggle forkCheck for adjustment
Reassembly
Change
Change
Change
Burning bearing, burning gear Over-low oil level
Inferior lubricating grease
Non-timely oil change, over-dirty oil
Inter-use of differential oil or usage of
additiveChange damaged parts and add oil
Change the damaged parts and lubricating oil
Change damaged parts and lubricating oil
Change damaged parts and lubricating oil
Difficult in gear disengagement Spring invalidation of synchronizer
Warn inner groove of tooth ring of synchronizer
Tooth ring of synchronizer choked on conical
face
Toggle fork deformation or toggle fork axle
deformation
Severely worn toggle forkChange
Change
Change
Change
Change
Methods for troubleshooting
Over-loud or abnormal noise
Common Failures Causes

TF-3Transfer Box
Troubleshooting
Common troubles Causes Resolving approaches
Change the lubricant or supplement the
lubricant volume.
Guarantee the torque of all connecting
elements stand at the specified value.
Open the transfer case to check the
bearing and othe parts whether is weared
or daamaged,if this happened,change
the parts.
Difficulty in mechanic gearshift or
outplace gear engagement
Troubleshooting
Incorrect lubricant or insufficient
lubricant volume.
Looseness of connecting bolt or other
connecting element.
Noise from the transfer box bearing Noise, which is spreader by the transfer
box instead of clutch, engine, drive shaft
and other parts, occurs in each speed. No driving of front wheel in the four-
gear engagementDrive chain breakDisassemble and check the damage of
inner parts, and change the chain. Adjust or repair shift lever.Open the
transfer box to check the toggle fork and
guide shaft, and change the parts as
requirement.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts.Open
the transfer box to check whether the
parts is wearied or not, and, if any, change
the weary parts.Open the transfer box to
check whether the parts is wearied or not,
and, if any, change the weary parts. Overlarge loose fit clearance of the
shift toggle fork on the shift guide
shaft.
Wear of the shift toggle fork
assembly including pin and contact
roller.
Wear of the shift cam hub and the
liner.
Attainment of coupling gear Mechanic gearshift seizing at a certain
location Engagement failure of the mechanically
shift transfer boxDamage or unsuitable adjustment of
the shifting mechanism.
Damage or serious wear of the inner
shifting parts, or looseness or
attainment of the shift toggle fork
assembly on the guide shaft.
Unsuitable adjustment of shift lever.Adjust or repair the shift lever mechanism.
Change the seriously wearied parts.
Change the loose or weary parts. Refer to the vehicle manual for correct
operation.
Add the specified oil of given volume.
Open the rear cover of transfer box to check
and changer the damaged parts.
Open the rear cover of the transfer box to
check whether the sliding parts can slide
freely along the axle, if not, dismantle it and
change the damaged parts. Incorrect operation.
Lubricant of inferior quality or
insufficient volume.
Adhesive bonding of shift toggle fork.
Adhesive bonding of the sliding joint
cover, locking sleeve or gear. Mechanic gearshift failure under the
movement of shifting handleBreak or damage of the shift rocker
arm or shift lever.
Damage of the guide plate of shifting
cam;Change the damaged element.
Open the rear cover of the transfer box to
check the damaged element and change
it. Electric gearshift troubleDamage or failure of electrically
controlled element, electric module,
speed sensor, electric motor, electric
clutch, or built-in wire harness.
Damage or worn of shifting cam,
joint cover, locking sleeve, toggle
fork or shift guide axle.Adhesive
bonding shiftRefer to the vehicle usage manual to
diagnose the failure element and change
it as requirement.
Dismantle the weary or damaged parts
and change it as requirement.
Dismantle and check the free movement
of sliding element, and change it as
requirement

TF-9
5 4
3
1
6 2
1. rear body of transfer box
2. flange
3. oil seal
1. sensor bracket
2. bolt
3. speed sensor
4. o-ring
5. sensor assembly
6. bolt
7. gasket
8. rear body of transfer box2 1
5 3
4
4
6
7
8
Transfer Box
Disassembly of Transfer Box
4. gasket
5. nut
6. oil plug
Disassembly of Transfer Box
1. Brief instruction
In case the transfer box is required to be repaired for the
damaged specific element, it shall be taken apart to the degree
on which the damaged element is taken out. And the parts
taken apart from the transfer box, if it doesnít include the
damage element, can exist in the form of sub-assembly or
group instead the individual form, otherwise, the parts will be
taken apart individually.
2. Transfer Box Disassembly
Put the transfer box on the worktable and ensure the rear part
or the rear cover faces upward. Put the wooden block under the
front part of transfer box to keep the transfer box stands
horizontally. The disassembly process is as follows:
(a) Fasten the flange with the torque arm typed T-13-54-
002, screw off the nut to take down the gasket, then take
apart the flange and oil seal.
(b) Take down the two oil plugs from the transfer box body.
As for the electric gearshift transfer box, tear down the
electric shifting element according to the following
disassembly approach:
(a) Tear down the three bolts, gaskets, sensor and clip for
wire harness.
(b) Tear down the sensor assembly and take apart the O-
ring.
(c) Tear down the motor assembly.

TF-24Transfer Box
Washing, Checking, Up-Keeping and Exchanging (Washing)
1. Washing
Notice: check the metal rag around the magnet first before washing, large granule or irregular metal
granule shows the disintegratation or similar damage. Small or fine metal granule shows the uneven
or serious wear. If the metal rag is founded, notice shall be taken on damage and wear inspection
during checking the rotating parts and the element matched with the rotating parts.
(a) Common washing
Wash the parts in cleaning agent to clean away the old lubricant and deposit. Clean away the deposit in oil hole
with brush. Take notice not to scrape the metal coupling face when washing the parts cannot be cleaned with
brush.
(b) Dry the washed parts by blowing
Dry the washed parts by blowing the low-pressure compressed air (max pressure is 137.9kPa), because cloth
thread may be left during cleaning the parts with cloth. The bearing shall be held by hand to prevent it from
rotating when blowing it.
(c) Bearing lubrication
The ball bearing and needle bearing shall be lubricated with the lubricant for transfer box after washing. As
the non-lubricated bearing may cause damage when be dry. Cover the lubricated bearing to prevent dust
entering in.
Washing, Inspection, Maintenance or Change