2006 FIAT MULTIPLA dashboard

182
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
FOR CHECKING AND RESTORING PRESSURE ONLY
The compressor can be also used just for restoring pressure. Disconnect
the quick connection and connect it directly to the tyre valve; in this way
the cylinder is not connected to compressor and the sealing fluid will not
flow into the tyre.
CYLINDER REPLACEMENTPROCEDURE
To replace cylinder proceed as follows:
❒disconnect connection (A);
❒turn counter-clockwise the cylinder to replace and raise it;
❒fit the new cylinder and turn it clockwise;
❒connect connection (A) to the cylinder and fit the transparent tube (B)
into the proper space.
FOE0716m
FOE0721m

183
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
Where possible, have the lamps changed by Fiat Dealership. Correct operation and aiming of external
lights are essential for safe driving in compliance with law regulations.Halogen bulbs must be handled touching only the metallic part. If the transparent bulb is touched
with the fingers, its lighting intensity is reduced and life of the bulb may be compromised. If touched
accidentally, rub the bulb with a cloth moistened with alcohol and allow to dry.
IF A BULB BURNS OUT
GENERAL INSTRUCTIONS
❒Before changing a bulb check the contacts for
oxidation.
❒Burnt bulbs must be replaced by others of the same
type and power.❒Always check headlight aiming after changing a bulb
to ensure they are safe.
❒When a light is not working, check that the
corresponding fuse is intact before changing a bulb.
For the location of fuses, refer to the paragraph “If a
fuse blows” in this section.
Alterations or repairs to the electric system not carried out correctly and without
taking into account the system specifications may cause failures and the risk of
fire.WARNING
WARNINGHalogen bulbs contain pressurised gas, in the case of breakage they may burst.

184
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
TYPES OF BULBS
Different types of bulbs are fitted on the car.
A Glass bulbs
Press fitted.
To remove them, pull.
B Bayonet connection bulbs
Remove from the bulb holder by pressing the bulb
and rotating it anti-clockwise.
C Cylindrical bulbs
To remove them, release them from their contacts.
D Halogen bulbs
To remove, release the locking spring and take out
the bulb.E Halogen bulbs
To remove, release the locking spring and take out
the bulb.
IMPORTANT The headlight inner surface might be
slightly misted: this should not be considered irregular
but a natural phenomenon due to low temperature
and the air humidity level. Misting will disappear as
soon as the headlights are turned on.
Drops inside the headlight mean water infiltration:
contact Fiat Dealership.
F0E0622m

185
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
12V-5W
12V-55W
12V-55W
12V-21W
12V-5W
12V-55W
12V-21/5W
12V-21W
12V-21/5W
12V-21W
12V-2,3W
12V-5W
12V-10W
12V-10W (*)
12V-1W
12V-5W W5W
H7
H1
P21W
WY5W
H1
R5W
P21W
P21W
P21W
–
W5W
C10W
C5W
–
W5W A
D
E
B
A
E
B
B
B
B
A
A
C
C
C
A
Bulbs Ref. figure Type Power
Front side lights
Dipped beams
Main beams
Front direction indicators
Side direction indicators
Front fog lights
(where provided)
Rear light cluster
- side/taillights
- reversing light
- fog light
- direction indicators
Third brake light
Number plate light
Front ceiling light
Rear ceiling light
Vanity mirror light
Boot light
(*) 12V-5W in versions with sunroof.

186
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
IF AN EXTERIOR LIGHT BURNS OUT
For the type of bulb and power rating, see “If a bulb burns out”.
FRONT LIGHT CLUSTER
The front light cluster contains sidelight, dipped beam, main beam
direction indicator and fog light bulbs.
To change the bulbs of the sidelights, dipped beams, direction indicators
and front fog lights it is necessary to remove the cover (A) releasing the
catch (B).
The bulbs are arranged inside the light cluster as follows:
C: dipped beams
D: front fog lights
E: sidelights
F: main beams
G: direction indicators
After replacement, refit the covers correctly checking that they are
properly secured.
F0E0644m
F0E0645m

187
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
MAIN BEAMS
To change the bulb, proceed as follows:
❒turn cap (A) counterclockwise and remove it;
❒disconnect the electric connector (B);
❒release the bulb holder catch (C);
❒remove the bulb (D) and replace it;
❒refit catch (C), reconnect the electrical connector (B) and refit cap
(A) turning it clockwise. Cap vent (H) shall be set from the top
downwards.
DIPPED BEAMS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the catch;
❒disconnect the electric connector (F);
❒release the bulb holder catch (E);
❒remove the bulb (G) and replace it;
❒fit the new bulb, making the outline of the metallic part coincide with
the grooves on the reflector, then hook the bulb holder catch (E) and
reconnect the electrical connector (F) ;
❒refit the protective cover correctly.
F0E0646m
F0E0647m
F0E0648m

188
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
DIRECTION INDICATORS
Front
To change the bulb, proceed as follows:
❒remove the protective cover releasing the catch;
❒turn the bulb holder (A) counterclockwise and remove it;
❒remove the bulb (B) pushing it gently and turning counterclockwise
(“bayonet connection”);
❒replace the bulb;
❒refit the bulb holder turning it clockwise, checking that it is secured
correctly;
❒refit the protective cover correctly.
Side
To change the bulb, proceed as follows:
❒push the lens (A) by hand in running direction to compress the catch;
❒remove the unit;
❒turn the bulb holder (B) counterclockwise, remove the snap-fitted
bulb (C) and replace it;
❒refit the bulb holder (B) in the lens then position the unit making sure
the catch clicks into place.
F0E0649m
F0E0650m

189
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
FRONT SIDELIGHTS
To change the bulb, proceed as follows:
❒remove the protective cover releasing the catch;
❒remove the snap-fitted bulb holder unit (A), take out bulb (B) and
replace it;
❒refit the snap-fitted bulb holder unit (A);
❒refit the protective cover correctly.
FRONT FOG LIGHTS (where provided)
To change the bulb, proceed as follows:
❒disconnect the electric connector (C);
❒release the bulb holder catch (D);
❒remove the bulb (E) and replace it;
❒fit the new bulb, hook the bulb holder catch (D) and reconnect the
electrical connector (C).
F0E0651m
F0E0652m