2006 FIAT MULTIPLA lock

25
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
ACCESSING THE MAIN MENU
The main menu can be opened from the standard display when the car is stationary. Press the button according to
MODE 1.
Use buttons
âand ãto navigate.
Either the standard display or the menu which was open before the button was pressed according to MODE 1 will
reappear after a waiting time longer than 10 seconds (no operation for ten seconds). All settings which have not
been stored will be lost. Settings confirmed by MODE 1 will be stored.
Standard display
TRIP B
TIME
DAYLIGHT
SAVING TIME
CLOCKMODE
12/24
LANGUAGE
DISTANCE
CONSUMPTION
TEMPERATURE
BUZZER
SERVICE
SETUP OFF
See the chapter “Warning lights and messages” if a fault mes-
sage appears on the display. If there are two or more faults,
the respective messages will appear cyclically on the display.
To eliminate the warning message from the configurable mul-
tifunction display, press the button according to MODE 1
once for all messages. If the message “INERT. SW. ACTIVE”
appears, you will firstly need to reset the inertia switch (fu-
el cut-off switch) as shown in the respective paragraph. Go
to a Fiat Dealership if the message “CONFIG. ERROR” ap-
pears.
Q
Standard display Next menu
See
INITIAL
TESTâAre
you mov-
ing?NO
YES

30
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
DAYLIGHT SAVING TIME
Proceed as follows to switch the daylight saving time function (which corresponds to + 1 hour with respect to
normal winter time) on and off:
Menu
Next menu
Back to
standard display
â
ã
â
ãR
Q
R
Q
With DAYLIGHT SAVING ON, the system will
automatically switch to and from daylight sav-
ing time without needing to set the clock by
means of the TIME function described above.
See
ACCESSING
THE MAIN
MENU
Back to menu
â

31
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CLOCKMODE 12/24
This function is used to display the time by a 12 hour or 24 hour clock. Proceed as follows to make the setting:
Menu
Next menu
Back to
standard display
â
ã
â
ãR
Q
R
Q
See
ACCESSING
THE MAIN
MENU
Back to menu
â

41
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SEATS
FRONT SEATS
Moving the seat backwards or forwards (where provided)
Lift the lever (A) (on seat internal side) and push the seat forwards or
backwards: in the driving position the arms should rest on the rim of the
steering wheel.
Driver’s seat lumbar adjustment (where provided)
This gives better support to your back. To adjust, turn the knob (C).
Adjustment and lowering of seat back
Lift the lever (B) and adjust the slope of the seat back.
F0E0629m
Only make adjustments when the car is stationary.WARNING
Once you have released the lever, check that the seat is firmly locked in the
runners by trying to move it back and forth. Failure to lock the seat in place could
result in the seat moving suddenly and the driver losing control of the car.WARNING

43
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
Centre sliding seat (where provided)
Lift the lever (A) and push the seat forwards or backwards. After
releasing the lever, make sure the seat is correctly locked on the runners.
Moving the seats
To increase the boot load capacity the seats have two positions (three
for the centre seat).
To move the seats forward from the standard position, use the special
anchorages on the floor.
To set the centre seat in the most forward position (maximum load
position), bring the centre front seat fully forward and tip the seatback
over.
At this point, refit the rear seat, positioning the seat back as shown in the
figure in its most forward position.
The central seat can be moved backwards by 100 mm.
A - all forward position
B - standard position
C - all backward position
F0E0016m
F0E0232m
F0E0015m

44
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
HEAD RESTRAINTS
FRONT SEATS
To improve passenger safety, the height of the head restraints can be
adjusted. They will automatically lock in the position required.
To raise grip it at the base and pull upwards.
To lower press it downwards from above, keeping button (A) pressed.
When you release the button, check the restraints are firmly locked in
place.
REAR SEATS (where provided)
Only the rear seat head restraints can be removed.
To remove the head restraints:
1 - lift to the first notch
2 - press the two buttons (A) and (B) and remove the head restraints.
The special head restraint configuration interferes intentionally with the
rear passenger back correct positioning in order to oblige the passenger
to raise the head restraint for its proper use.
Remember that head restraints should be adjusted to support your head and not
your neck. Only if they are in this position will they be able to provide effective
protection in the event of a rear-end shunt.WARNING
F0E0231m

45
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
STEERING WHEEL
It can be adjusted vertically.
1) Move lever (A) to position 1.
2) Adjust the steering wheel position.
3) Return the lever to position 2 to lock the wheel in place again.
F0E0018m
All adjustments must be made when the car is stationary.WARNING

63
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CEILING LIGHT
FRONT CEILING LIGHT
Switch (A) turns the ceiling lights on/off.
Switch (B) controls the spot light.
According to the position, you can have the following conditions:
❒with switch (A) in centre position, ceiling lights (C) and (D) will turn
on when front doors are opened;
❒with switch (A) moved to the left, ceiling lights (C) and (D) are off and
will not turn on when opening or unlocking the doors;
❒with switch (A) moved to the right, ceiling lights (C) and (D) remain
on.
Switch (B) turns the following lights on separately:
❒map light (C) if moved to the left;
❒map light (D) if moved to the right.
IMPORTANT Before getting out of the car, make sure that both switches
are in centre position; ceiling lights will turn off when doors are closed,
saving the battery.
F0E0065m
F0E0236m