2006 FIAT DUCATO ESP

10GETTING TO KNOW YOUR VEHICLE
IMPORTANTThe remote control
system frequency can be disturbed by
significant radio transmissions outside
the car (e.g: mobile phones, HAM ra-
dio systems, etc.) that could cause re-
mote control malfunctioning.
MINISTERIAL
HOMOLOGATION
In the respect of the legislation in
force in each country in the matter of
radio-frequency devices, please note
that:
– the market-specific homologation
numbers are listed in paragraph “Ra-
dio-frequency remote control” in sec-
tion “Technical Specifications”.
– the homologation number is print-
ed on the component for markets
where this is required.
fig. 6
F0D0130m
To insert the metal insert in the key
grip, keep the button Epressed and
turn the insert in the direction shown
by the arrow until hearing the click as
it locks into place. Then release the
button E.
For instructions on ordering addi-
tional remote controls or replacing
the batteries, refer to the relevant
paragraphs in the following pages. Re-
fer to “Radio-frequency remote con-
trol” in section “Technical Specifica-
tions” for the relevant ministerial ho-
mologation.
When pressing the button
E, take care to prevent the
metal insert from causing harm or
damage when it comes out. The
button E should only be pressed
when the key is away from the
body, in particular from the eyes,
and from objects that can be spoilt
(e.g.: clothes). Make sure the key
can never be touched by others, es-
pecially children, who may inad-
vertently press the button E.
WARNING

20GETTING TO KNOW YOUR VEHICLE
fig. 18
F0D0003m
The webbing must not be
twisted. The upper section
must pass across the shoulder and
chest diagonally. The lower section
must fit closely across the passen-
ger’s hips and not the abdomen (fig.
18). Do not use clips, fasteners, etc.
to prevent the belt adhering to the
passenger’s body.
WARNING
Under no circumstances
should the components of
seat belts and pretensioners be
tampered with or removed. Any in-
terventions should be carried out by
qualified and authorised personnel.
Always contact a Fiat Dealership.
WARNINGGENERAL INSTRUCTIONS
FOR THE USE OF THE SEAT
BELTS
The driver is responsible for re-
specting and enforcing the local rules
and laws regarding the use of seat
belts.
Always fasten the seat belts before
starting.
For maximum safety, keep
the back of your seat up-
right, lean back into it and make
sure the seat belt fits closely across
your chest and hips. Always fasten
seat belts, in front and rear seats!
Travelling without seat belts in-
creases the risk of severe and fatal
injury in the event of a crash.
WARNING

25GETTING TO KNOW YOUR VEHICLE
GROUP 2
Children from 15 to 25 kg can be se-
cured directly with the vehicle seat
belts. The seat has the purpose of po-
sitioning the child correctly with respect
to the seat belt so that the diagonal sec-
tion crosses the child’s chest (never the
child’s throat) and the horizontal sec-
tion fits snugly on the child’s hips (and
not the child’s abdomen) fig. 24.GROUP 3
For children from 22 kg up to 36 kg
the size of the child’s chest no longer
requires a support to space the child’s
back from the seat back.
The fig. 25shows proper child seat
positioning on the rear seat.
fig. 24
F0D0009m
fig. 25
F0D0010m
The figure is only an exam-
ple. Attain to the instruc-
tions for fastening which must be
enclosed with the specific child re-
straint system you are using.
WARNING
Children taller than 1.5 m can wear
seat belts like adults.
The figure is only an exam-
ple. Attain to the instruc-
tions for fastening which must be
enclosed with the specific child re-
straint system you are using.
WARNING

36GETTING TO KNOW YOUR VEHICLE
LOW ENGINE OIL
PRESSURE (red)
When the engine oil pres-
sure falls below the normal level. The
light comes on when you turn the ig-
nition key to MARand should go out
as soon as the engine starts.
A delay in the light going out is ac-
ceptable when the engine is idling. If
the engine has been taxed heavily, the
light may flash when idling. It should,
however, go out when you acceler-
ate slightly.vASR (ANTISLIP
REGULATION
SYSTEM) (amber)
Turning the ignition key to MAR,
the warning light turns on, but it
should go off after few seconds.
The warning light flashes when the
system cuts in, to alert the driver that
the system is adapting to the road sur-
face grip conditions.
When the system is turned off with
the specific button, the warning light
comes on without flashing.
When the system is on and an ASR
fault is detected, the warning light
comes on without flashing. Check that
the information is correct by pressing
the button once (in this way, if the
system is working and the ASR is re-
stored, the warning light will go off,
but if there is a system failure, the ASR
will not be restored and the warning
light will stay on).
In this case contact a Fiat Dealer-
shipas soon as possible.PASSENGER SIDE
AIRBAG
DEACTIVATED
(amber)
When the passenger airbag has been
deactivated by means of the respec-
tive key switch.
FV
If the warning light comes
on when the vehicle is run-
ning, stop the engine and contact a
Fiat Dealership.
WARNING
Warning light Findicates
also warning light ¬fail-
ure. This is indicated by intermit-
tent flashing, over 4 seconds, of
warning light F. In this event,
warning light ¬could be not up to
indicate restraint system failures, if
any. Stop the car and contact Fiat
Dealership to have the system
checked.
WARNING

37GETTING TO KNOW YOUR VEHICLE
EOBD ENGINE
FAILURE CONTROL
SYSTEM
(petrol versions only) (amber)
In normal conditions, the warning
light will come on when the ignition
key is turned to MARand should go
out as soon as the engine is started.
The initial lighting up shows that the
warning light is working properly.
If the warning light either stays on or
comes on while travelling:
1. Fixed light- warning of a fuel
feed/ignition system failure which may
increase emissions in exhaust or cause
possible drops in performance, poor
handling and high consumption.
In such conditions, you can contin-
ue driving but you should not tax the
engine and you should moderate the
speed. Prolonged use with the warn-
ing light on can cause damage. Contact
a Fiat Dealershipas soon as possi-
ble. The warning light will go out when
the failure disappears. In any case, the
system will store the error.
2. Flashing- warning that the cata-
lyst can be damaged (see “EOBD sys-
tem” in this chapter).
If the warning light starts flashing, re-
lease the accelerator pedal and slow
the engine until the warning light stops
flashing. Continue driving at moderate
speed, preventing the warning light
from coming on again. Contact a Fi-
at Dealership as soon as possible.INJECTION SYSTEM
FAILURE
(diesel versions) (red)
When there is a fault in the injection
system.
The warning light should come on
when the ignition key is turned to
MARand go out after a few seconds.
The warning light will stay on or come
on when travelling to indicate imperfect
operation of the injection system with
possible loss of performance, poor han-
dling and higher consumption.
In these conditions, you can contin-
ue driving but you should avoid de-
manding efforts from the engine or
high speeds. Contact a Fiat Dealer-
shipas soon as possible.
Prolonged use of the vehicle with the
warning light on can cause damage to
the engine, especially in the event of
misfiring. The vehicle can only be dri-
ven for a short period of time at low
speeds.
Occasional and brief lighting of the
warning light is meaningless.
UU
Contact a Fiat Dealer-
ship as soon as possible if
the
Uwarning light ei-
ther does not come on when the
key is turned to MAR or comes
on, with fixed light or flashing
light, when travelling. Warning
light
Uoperation can be checked
by means of special equipment by
traffic agents. Always comply
with the road traffic regulations
in force in the Country where you
are travelling.

56GETTING TO KNOW YOUR VEHICLE
DEMISTING AND/OR
DEFROSTING THE REAR
WINDOWS
Press button (.
You are advised to switch the button
off as soon as the rear windows are
clear.VENTILATION
Control settings to obtain the re-
quired ventilation.
1)Centre and side vents: complete-
ly open.
2) Air temperature knob: pointer in
the blue sector.
3) Air recirculation slider: pointer at
Ú.
4)Fan knob: pointer at the required
speed.
5)Air distribution knob: pointer at
O.AIR RECIRCULATION
With the slider at Òthe internal
air is recirculated.
IMPORTANT This function is par-
ticularly useful when the outside air
is heavily polluted (in a traffic jam, tun-
nel, etc.). You are advised against us-
ing this function for long periods, how-
ever, especially if there are a lot of pas-
sengers in the vehicle as it could lead
to the windows misting up.

57GETTING TO KNOW YOUR VEHICLE
CLIMATE CONTROL
SYSTEM
CONTROLS fig. 81
A- Fan knob.
B- Air temperature knob (mixing
hot and cold air).
C- Air distribution knob.
D- Air recirculation slider to cut off
outside air.IMPORTANTThis function speeds
up the air cooling in summer. It is par-
ticularly useful when the outside air
is heavily polluted (in a traffic jam, tun-
nel, etc.). You are advised against us-
ing this function for long periods, how-
ever, especially if there are a lot of pas-
sengers in the vehicle.
E- Climate control system on/off
button.The Panorama and Combi versions
are equipped with a climate control
system consisting of a main system and
a supplementary system (optional) fig.
82set on the left-hand wall near the
first row seats.
fig. 81
F0D0205m
fig. 82
F0D0074m

62GETTING TO KNOW YOUR VEHICLE
fig. 87
F0D0132m
fig. 88
F0D0134m
fig. 89
F0D0136m
“Heat now” function fig. 87
To turn the heater on manually,
press timer button 8. The display and
warning light 1will stay on while the
heater is in use.
Programming the heater
Before programming the heater, set
the clock.Setting the clock
– Press button 4: display and warn-
ing light 9-fig. 88will light up.
– Within 10 seconds, press button 5
or 7to select the correct time.
Keeping button 5or 7pressed will
fast forward or backward the clock.
Reading the clock fig. 88
To read the clock, press button 4:
current time will be displayed for ap-
proximately 10 seconds. Warning light
9will come on.Programmed heating fig. 89
Heater ignition can be delayed from
1 minute to 24 hours. Three different
times can be programmed but only
one will be used.
To program starting time:
– press button 6: either symbol 10
or the previously programmed time
and number 3 (corresponding to the
preset function recalled) will light up
for 10 seconds;