2006 FIAT DUCATO ESP

186TECHNICAL SPECIFICATIONS
E- Maximum vehicle weight fully
loaded
F - Maximum vehicle weight fully
loaded with trailer
G - Maximum vehicle weight on
front axle
H - Maximum vehicle weight on rear
axle
I - Engine type
L - Body version code
M - Smoke opacity index (for diesel
engines).
This plate is fastened to the front
crossmember in the engine compart-
ment A-fig. 3.BODYWORK PAINT
IDENTIFICATION PLATE
The plateA-fig. 4 is set on the left-
hand inner side of the bonnet.It bears the following data fig. 5:
A - Paint manufacturer
B - Colour name
C - Fiat colour code
D- Respray and touch up code.
fig. 3
F0D0188m
fig. 4
F0D0189m
fig. 5
F0D0025m

214TECHNICAL SPECIFICATIONS
ENGINE
GENERAL FEATURES
Engine code
Cycle
Number and layout of cylinders
Diameter x stroke mm
Total capacity cm3
Compression ratio
kW
Maximum power output EEC HP
corresponding ratio rpm
Nm
Maximum torque EEC kgm
corresponding ratio rpm
Spark plugs
Fuel
2.0
RFL
Otto
4 in line
86x86
1998
9.5 : 1
81
110
5700
168
17.1
3700
RC9YCC
RFC52LS
Unleaded
petrol
95 RON2.0 JTD
RHV
Diesel
4 in line
85x88
1997
17.6 : 1
62
84
4000
192
19.6
1900
–
Diesel for
motor vehicles
(EN590
specifications)2.3 JTD
F1AE0481C
Diesel
4 in line
88x94
2286
19 : 1
81
110
3600
270
27.6
1800
–
Diesel for
motor vehicles
(EN590
specifications)2.8 JTD
8140.43 S
Diesel
4 in line
94.4x100
2800
18 : 1
93.5
127
3600
300
30.6
1800
–
Diesel for
motor vehicles
(EN590
specifications)2.8 JTD
POWER
8140.43 N
Diesel
4 in line
94.4x100
2800
18 : 1
107
146
3600
310
31.6
1500
–
Diesel for
motor vehicles
(EN590
specifications)

219TECHNICAL SPECIFICATIONS
UNDERSTANDING TYRE
MARKINGS
The following are the necessary in-
dications to understand the meaning
of the markings on the tyre.
195= Nominal width
(S, distance between side
walls in mm).
70= Height/width ratio (H/S,
as a percentage).
R= Radial tyre.
15= Rim nominal diameter in
inches (Ø).
C= Letter identifying tyres
for light-duty
transportation.
103/101= Load rating (carrying ca-
pacity).
Q= Maximum speed rating.6= rim in inches (1)
J= rim drop centre outline
(side projection where the
tyre bead rests) (2)
15= rim nominal diameter in
inches (corresponds to di-
ameter of the tyre to be
mounted) (3 = Ø)
H2= “hump” shape and number
(relief on the circumfer-
ence holding the tubeless
tyre bead on the rim) Maximum speed rating
Q= up to 160 km/h.
R= up to 170 km/h.
S= up to 180 km/h.
T= up to 190 km/h.
U= up to 200 km/h.
H= up to 210 km/h.
V= up to 240 km/h.
Maximum speed rating
for snow tyres
Q M+S= up to 160 km/h
T M+S= up to 190 km/h
H M+S= up to 240 km/hUNDERSTANDING RIM
MARKINGS
The following are the necessary in-
dications to understand the meaning
of the markings on the rim.
Example: 195/70 R 15C 103/101 QExample: 6J x 15 H2
fig. 6
F0D0031m

227TECHNICAL SPECIFICATIONS
VAN WEIGHTS
Weights (kg)
Version 11 (*)
Kerb weight
(including fuel,
spare wheel, tools
and accessories):
Payload including
driver (1):
Maximum admitted
loads (2)
– front axle:
– rear axle:
– total:
Towable weight:
– trailer with brakes
– trailer without brakes
Maximum load on ball coupling
(trailer with brakes)
Maximum load on roof
(1) If special equipment is fitted (tow hitch, etc.), the unladen vehicle weight increases, thus reducing the specified payload.
(2) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.
* The figures given refer to panelled and glazed vans with medium and short wheelbase, both high and low sided.2.0
1695 ÷ 1780
1120 ÷ 1170
1600
1600
2865 ÷ 2900
2000
750
80
1002.0 JTD
1755 ÷ 1840
1060 ÷ 1145
1600
1600
2900
1600
750
80
1002.3 JTD
1825 ÷ 1910
990 ÷ 1075
1600
1600
2900
2000
750
80
1002.8 JTD
1850 ÷ 1935
965 ÷ 1050
1600
1600
2900
2000
750
80
100

228TECHNICAL SPECIFICATIONS
Weights (kg)
Version 15 (*)
Kerb weight
(including fuel,
spare wheel, tools
and accessories):
Payload including driver (1):
Maximum admitted
loads (2)
– front axle:
– rear axle:
– total:
Towable weight:
– trailer with brakes
– trailer without brakes
Maximum load on ball coupling
(trailer with brakes)
Maximum load on roof
(1) If special equipment is fitted (tow hitch, etc.), the unladen vehicle weight increases, thus reducing the specified payload.
(2) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.
* The figures given refer to panelled and glazed vans with long, medium and short wheelbase, both high and low sided.2.0
1695 ÷ 1865
1435 ÷ 1510
1750
1850
3245 ÷ 3300
2000
750
80
1002.0 JTD
1755 ÷ 1840
1435 ÷ 1505
1750
1850
3300
1600
750
80
100
2.3 JTD
1725 ÷ 1995
1305 ÷ 1475
1750
1850
3300
2000
750
80
100
2.8 JTD
2.8 JTD POWER
1850 ÷ 2020
1280 ÷ 1450
1750
1850
3300
2000
750
80
100

229TECHNICAL SPECIFICATIONS
Weights (kg)
Version MAXI (*)
Kerb weight
(including fuel,
spare wheel, tools
and accessories):
Payload including driver (1):
Maximum admitted
loads (2)
– front axle:
– rear axle (3):
– total:
Towable weight:
– trailer with brakes
– trailer without brakes
Maximum load on ball coupling
(trailer with brakes)
Maximum load on roof
(1) If special equipment is fitted (tow hitch, etc.), the unladen vehicle weight increases, thus reducing the specified payload.
(2) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.
(3) See “Cold tyre inflation pressure”.
* The figures given refer to panelled and glazed vans with long and medium wheelbase, both high and low sided.2.0
1765 ÷ 1915
1585 ÷ 1735
1850
2120
3500
2000
750
80
1002.3 JTD
1895 ÷ 2045
1455 ÷ 1605
1850
2120
3500
2000
750
80
100
2.8 JTD
2.8 JTD POWER
1935 ÷ 2070
1430 ÷ 1565
1850
2120
3500
2000
750
80
100

230TECHNICAL SPECIFICATIONS
PANORAMA WEIGHTS
Weights (kg)
Short wheelbase version
Kerb weight
(including fuel,
spare wheel, tools
and accessories):
Payload including driver (1):
Maximum admitted
loads (2)
– front axle:
– rear axle:
– total:
Towable weight:
– trailer with brakes
– trailer without brakes
Maximum load on ball coupling
(trailer with brakes)
Maximum load on roof
(1) If special equipment is fitted (tow hitch, etc.), the unladen vehicle weight increases, thus reducing the specified payload.
(2) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.2.0
1925
8P + 431 kg
1600
1600
2900
2000
750
80
1002.0 JTD
1985
8P + 371 kg
1600
1600
2900
1600
750
80
1002.3 JTD
2055
8P + 301 kg
1600
1600
2900
2000
750
80
1002.8 JTD
2080
8P + 276 kg
1600
1600
2900
2000
750
80
100

231TECHNICAL SPECIFICATIONS
Weights (kg)
Medium wheelbase version
GRAND VOLUME
Kerb weight
(including fuel,
spare wheel, tools
and accessories):
Payload including driver (1):
Maximum admitted
loads (2)
– front axle:
– rear axle:
– total:
Towable weight:
– trailer with brakes
– trailer without brakes
Maximum load on ball coupling
(trailer with brakes)
Maximum load on roof
(1) If special equipment is fitted (tow hitch, etc.), the unladen vehicle weight increases, thus reducing the specified payload.
(2) Loads not to be exceeded. The driver is responsible for arranging the loads so that they comply with these limits.2.3 JTD
2195
8P + 561 kg
1750
1850
3300
2000
750
80
100 2.0
2065
8P + 691 kg
1750
1850
3300
2000
750
80
1002.8 JTD
2220
8P + 536 kg
1750
1850
3300
2000
750
80
100